Come on boys and girls! Put your EV charger at the top of the panel not the bottom: 1. Voltage Stability: The circuits nearest to the main breaker (typically at the top of the panel) may experience slightly less voltage drop, as they are closer to the incoming power supply. This can be beneficial for delicate or power-hungry devices that require stable voltage levels. 2. Power Factor and AC Noise: Sensitive loads, such as EV chargers or other high-demand equipment, can be more susceptible to noise and power factor issues. Placing them near the top of the panel reduces the chance of interference from other circuits, which may introduce noise or harmonics into the system. 3. Load Balancing: It’s also good practice to distribute high-demand loads evenly across the panel to avoid overloading one side. However, placing sensitive loads higher up can help in maintaining better overall system performance.

Regarding the Redi sealant used for the Redi flashing…Can I use this Redi sealant on the heads of cement backer board screws??? Or should I just cover them with thinset?

Drywall saw causes lots of dust and debris. So another reason to wear eye protection,….

Drywall saw causes lots of dust and debris. So another reason to wear eye protection,….

Wear GOGGLES….LITTLE DEBRIS fell OUT into EYE. I tryed to irrigate it . But eventually CAUSING ME TO go to E\R ROOM by Uber…….WAS A LITTLE PIECE OF METAL AND WOOD……. AND BLOWN IN INSULATION., LEARN FROM OTHERS MISTAKES. Hurt like helll…….…………

Great job

NOT a great way to do the hatches! A better method is to do the hatches first and leave a 1/4 - 1/2 inch lip over the edge of the hatch where you can, this provides a clean square edge either by a virgin board with only the tongue cut off or a nicely clean cut piece. If the hatch is slightly out of square, which most are not you may have to sand the edge slightly flush to the hatch. Then butt your adjacent pieces against those edges with a thin piece of poster board as a spacer to allow some even space around the hatch. Once you match the floor around the hatch the edges will be very clean and look much better than using a saw, grinder or vibrating saw to cut open around the hatches. Hatches are a necessary evil within boat floors but you can make them look much cleaner than this method.

Keep them videos coming!! You helped me tear down my old bathroom and rebuild it from studs. I work in healthcare and never attempted it but it came out pretty good using your videos as reference. Thank you.

It's awesome to see the difference in sizes and great vid on the install

WHOA WHOA WHOA, when did you get a roof! big jump from last video!

using them as you speak, walls come in 2 weeks for foundation/ basement! also keep in mind if you like high ceilings its less than a $1000 per foot height. i started with 8' for my basement an quickly went to 10' when i found that out. wanna say it was $830 per one foot higher wall

Another comment mentioned this, but towards the end I’m not seeing what those screws are going into other than just drywall which doesn’t work. It is where you say how incredibly tight those screws get.

Yeah never use a grinder again.

By the time you put that piece of rubber on there, I’d have the toilet seated.

How much do they pay for doing this??

Just time pass for long video

ready for more videos

It is evident and well-explained. If someone complains, they should buy and test one of these trucks themselves.

Which package involves the muffler delete -- the sport exhaust or the track package?

One of the best and easiest trick to clean your popcorn machine. Saves time and money. Don't over think it people, it works...... Thank you.....

use a grinder with a cutting blade

Where did you get the beams? How much a a linear ft. How did you determined the size? Any info?

The Redi sealant used with Redi flash…can I use this sealant for screw holes? Or is it better to use thinset?

I'm going with the epoxy.

push fit could have been easily fixed

Thank you, I knew nothing about M copper.

This is the same dealer my 2019 Sprinter has been to 4 times in the last 4 months. The Def system constantly having issues. Just got it back from them saying that it needed some module update. Now the ac blows only maximum hot air all the time. It's gotta go back again!!!!! This diesel V6 is the most reliable engine ever before the DPF system was added. I have another sprinter with 300K. Only issues were the DPF system. Repeatedly. They have an extended blue tech warranty for that system, so it's fixed free every time, but the down time sucks.

What size grommet do you use for the cut outs in the junction box?😅

thanks

Dealer wanted $566 .00 to install mine😳

Very good!

Perfect brother. Much respect!

Its all about pipe preparation. Not even taking in the cost of the fittings, those plumbers who spend 2-3 K on a batt. operated pro press tool find it hard to admit that it is not the best, even if you can get the same result with a shark bite. All about prep.

A fellow beat owner from VA 🫡

U saved my life i didnt know what to do on a job i just got im handy man but this video saved me now i can do it with confidence

Was the 7 pin round plug already installed from factory? My sprinter has a wire zip tied up in rear bumper area, but is a square plug. Not the seven pin round plug. I have a 2016

What a piece of gold this video. I plan to do this type of niche for my own house. Since I don't have as much experience, I'm simply not going to make it as complicated. What is your suggestion? Mosaic and then just cut in with large tile on the flanks?

Can these be used in Europe? Minimum pain: The battery can be charged by any existing USBc charger, so no additional charger needs to be carried and we can use battery packs. Medium pain: Charger needs a plug adapter. Max pain: charger needs a transformer.

If I may ask 2 questions…first..would you use redi-poxy on the area just above shower pan tile as prep for where wall tiles meet pan floor tiles? 2nd what thinset would you use on cement board walls to adhere 4x12 marble tile?

what happens if you check ohm resistance and there is an issue?

What kind/type of thinset and grout do you use to install Marbel tile onto shower walls

As a rule as an industrial plumber foreman: I only use Viega propress fittings and I only use type L copper. I have never had a problem.

Installing a 30" floating vanity now. You are right, the plumbing is an issue and not all the dimensions are given ( the rear opening). I am going to have to cut a rear support to make this work. And yes, the top doesn't snug to the wall.

Nice little shower with a shower pan that looks like 20 years old because I didn't care enough to protect it during construction!

Propress tools need calibration every so often. Probably some plumbers don't get their press re-calibrated as required and the machine doesn't press sufficiently.

Thanks for the new video! I’m looking forward to seeing what other content you post! Always good to learn as much as you can!

Do you always do a 50-50 pattern

Good explanation till you find pipes in the ceiling and then you have to cut a bigger piece of drywall since the Panasonic fan box is bigger than the small one I initially installed to move over the obstruction. Different scenarios in an apartment building. Not easy as it seems in a house

Also have a caliber recall and some updates apperley

Being a plumber by trade the only thing that levels a toilet is a flat floor. Good tile job etc. Usually I need to shim and calk a toilet to keep it from wobbling.