Very very, very, very, very bad

Regular wd-40 strips the lubricant from the torsion springs - see above for example. Instead, use a *white lithium grease* (also a wd-40 product) or if in a pinch, a viscous silicone lubricant. White lithium grease is less fluid and needs to be worked into a mechanism, use more than you think, get one with a bendable nozzle for control, wipe up excess

Beautiful doors. Great craftsman.

Thanks.

Where tf did I end up lol

you must set the left side 1st, then the right hand side.

Umm

I didn’t know which video to put my comment on, but this one is as good as any. I just finished installing the second new door on my two car garage and I can’t be happier. Ordered two classic steel doors from Clopay via Home Depot with the best insulation, hardware upgrade, insulated privacy windows, EZ Set torsion springs, and hanger kits. Had to reframe with new 2x6s as the old doors (1974) were not done well. New doors arrived about four weeks after ordering. Faster than expected. Was nervous to DIY this, but after watching some videos, I thought I can do that. Everything I needed was provided and the instructions were clear. Made some rookie mistakes with the first one, but nothing major. The second one was way easier, and both doors look fantastic. High quality doors and components at a very good price. I would recommend Clopay to anyone looking to upgrade their garage doors. Thank you!

oh duhh you only left out the part of how to remove the !#*@! spring. Should be titled Step 1 of 10 steps; 1. How to Release Standard Garage Door Torsion Springs.

This is to short of a video. We need more details

That last garage door in this video. What model is it?

❤️ that’s our house in the top pic! Thank you for featuring us.

Ok now how do we close it 😂

That was indeed very cool

You should.

That is absolutely amazing..

And you don't show the inside of the door - why? Because you're hiding the fact that the foam is just stuck to the back of the front sheet metal, rather than a sandwich where it's finished sheet metal panels on BOTH sides?

Go ahead and clean the reverse safety sensors with robin alcohol make sure that the sensors are facing to each other

I washed mine today, luckily I dont' think the neighbors saw me.

Love this video straight to the point, and exactly what I needed!!

Thanks for nothing good sir.

🤦🏼‍♀️

Bro said absolutely nothing! Lmao

Something tugged and pulled a wire apart inside of my motor. I had to splice it back together. It was associated to a sensor that controlled where the position of the door open and closed.

Why are you intentionally making useless youtube videos?

seems like there's a lot of "pro" installers in the comments that are feeling a bit threatened.....

Sure would be nice if clopay would do a 6/7/8/9 panel door install because the instructions on a 7 panel doors stink

Thank you for your very clear how to.

i'm trying to frame an 8' roll up into the end of my greenhouse, but I don't know how wide to make the frame or jamb? If it is an 8' door, is it just 8'? i measured from the end of the axle pole to opposite end and it is 102", or 8.5'. Any help is much appreciated!

He’s standing right in front of it

Will the shaft still be locked in place after loosening the set screws, or do you have to keep it from spinning with the pipe wrench?

What a waste of my time

Helped me.

Thank you for the help

Does that method work for the Sherwood type inserts? I’m trying to pull my inserts out but it feels it break

Thanks.

I’ve been installing garage doors for 8-9 years and this is NOT HOW YOU INSTALL A GARAGE DOOR

Exactly what I needed - joined a Facebook group turned out it was Trade Only - Boy did I encounter some downright rude SOB’s - they didn’t like it when I asked what university course did you major in as an Garage door installer - Seriously rude people when all I needed was someone to show me this video- I get it and understand the safety wires - idk what’s wrong with this trade my trade I’m more than willing to be proactive and save someone from injury in propane or compressed gasses and I have a pile of tickets and willing to help anyone for the sake of the industry- All I’ve heard all day is Call a professional or your on drugs - it’s a feckin roller door with two springs it’s not like setting four camshafts on a Range Rover V8 - of which I can do lols

Just the video I was looking for. Best part of KZfaq is how to videos like this one!

Clopay is all we sell. Aim Garage Doors, Inc. Harrisburg, PA area.

Thank you for this video!

Man, i'm on my 5th time watching this video. Just don't want to screw anything up.

What's the purpose of recording the measurements? It seems like the "you will need them later is not fully explained". Even in the directions i'm reading now in my manual they say to record the measurements and then nothing else about it.

This is the BEST little DIY video I’ve seen on here. Short, to the point, no ads, no talking. Ten thumbs up!

Beautiful.

Why do these houses have to be ridiculously large? All I see is wastefulness of resources.

'promo sm' 😎

I want to invest in a real company but I have never had the chance, I know you're your products and the quality, all I have is gold and a true want to make it, let me know know

Only thing I'm concerned about is how much head room it needs now of its a new build you can account for it but it's a fascinating product