Ive just had the very same issue and come accross this video. Being just about to go to work , yes I panicked untill I saw this which worked exactly as you say. A big thanks to you!
@krisfix1983Күн бұрын
@@adrianmitchell2635 you are welcome. Anytime
@user-ng3yg1fd4c7 күн бұрын
WHAT WAS THE SOLUTION
@colinstickland3130Ай бұрын
I am not telling you. Trade secret
@erdeijill84382 ай бұрын
Hi there! I got a we 1.4 petrol 2009 mk5 golf… it makes kida the same noise.. not sure what could that be… any help?
@krisfix19832 ай бұрын
Hi .this noise can come for a few reasons. First check swirl flaps noise can be similar , second put some valve lifter solution and drive it for a while to see if something is changing. If nothing changes remove the lifters cover and see if are playing. Thanks
@erdeijill84382 ай бұрын
@@krisfix1983 Where do i poor that solution in to?
@krisfix19832 ай бұрын
@@erdeijill8438 in oil
@erdeijill84382 ай бұрын
@@krisfix1983 great! Thank you! Will try it! Hopefully fixes the noise…
@charliepretorius75473 ай бұрын
Mine 1.4 16v sounds like a diesel in morning
@krisfix198315 күн бұрын
Common problem on this .
@mateenadnan45843 ай бұрын
Hi Sir I need Your Help Any Contact number
@nattyp78014 ай бұрын
My mini is a ‘12 & the oil filter is on top……
@RazvanRaita4 ай бұрын
This was helpfull thank you....
@krisfix19834 ай бұрын
You welcome. Anytime
@RafaTe-wn7sc4 ай бұрын
Hello! I have Reno Kajdar 1.2 turbo from 2018 and the mechanic told me he found metal shavings on oil filter so i want to ask your advice what to do thank you.
@krisfix19834 ай бұрын
Hi mate. Any unusual noises like chain rattle?
@RafaTe-wn7sc4 ай бұрын
@@krisfix1983 Thank you for reaching out Mate. There No unusual noise on the engine and also it doesn't take oil have no smoke but i think the first owners doesn't change oil regularly.
@krisfix19834 ай бұрын
@@RafaTe-wn7sc drain the oil and replaced. Before put a new oil and filters flush the engine to remove oil residual..be Verry careful with this engines make the oil service on time. No more than 5k between oil service. This is my advice
@RafaTe-wn7sc4 ай бұрын
@@krisfix1983 Thank you so much I really appreciate your effort to answer my questions I hope you will make a detailed video based on my question. Thank you again
@itzsaif25755 ай бұрын
Ive got a really bad one my engines making tapping noise n misfiring i replaced the spark plugs n done a full service on it. I have a video of it if i could send u it
@krisfix19834 ай бұрын
Check the timing chain.
@krisfix19834 ай бұрын
Swirl flaps, coil pack,or chain snapped
@krisfix19834 ай бұрын
Check the compression as well
@itzsaif25754 ай бұрын
@krisfix1983 thanks is there any way for me to send u the vid?
Forgot to mention .there is one metal pipe wich have a bracket on turbo. Right side 8 ml size ..you welcome
@R3VollveR6 ай бұрын
@@krisfix1983I managed to take everything besides the front intercooler pipe, I can see there’s a clip there on the plastic, how do I take that one off as I don’t want to damage it?
@krisfix19836 ай бұрын
@@R3VollveR the one on top the egine? Have 2 clips .with a screwdriver pull easily on both sides and you can take it out..don't take them off just pull like 1 cm and unclipp de hose
@R3VollveR6 ай бұрын
Thank you very much I managed to replace the turbo using your tutorial 👍
@krisfix19836 ай бұрын
@@R3VollveR you welcome ( cu placere
@R3VollveR6 ай бұрын
Hi mate, I got the same car my turbo failed and I’m trying to replace it could you do a video on how to do it please? All the bolts are in the back and can’t get to them do I need the engine out?
@krisfix19836 ай бұрын
Hi mate.i will do my best to make a video to explain you maybe tomorrow. You don't need to remove the engine .you need to remove the hose from air filter goes to turbo , wiring clip , the clamp holding the turbo to manifold wich have 10 mils size if I am not wrong..on turbo there are connected 3 metal pipes 2 on top wich have 2 bolts/each 13 size and 1 on bottom with 2, 8 size bolts wich are heavy to remove as no to much space .for me was easy to remove turbo as I had to remove the manifold ..sorry I hope you understand what I am explaining. After you remove all this be careful as looks like is welded is so hard to take it out from manifold ..a heater gun heat to manifold and after hit turbo easily to comes out
@R3VollveR6 ай бұрын
@@krisfix1983Are all bolts accessible from above or I need to get down under? Do you have a Facebook page to get in contact with you? Thanks 🙏
@krisfix19836 ай бұрын
@@R3VollveR send me your number to.contact you. After you can delete the message
@krisfix19836 ай бұрын
Dont get down under..all from top
@Professional_Youtube_Commenter6 ай бұрын
sure its not swirl flaps?
@krisfix19836 ай бұрын
You can see in video mate .not swirl flaps. Hydraulic lifters
@Professional_Youtube_Commenter6 ай бұрын
@@krisfix1983 wheres the after video, you said you'll make an after video so we can see the difference.
@tedy2009tedy7 ай бұрын
I ordered a new barrel for my vivaro 2005 because last year I have changed the wires with the switch for about 3 times. Now the problem I've got is that the new barrel does not fit properly. Firstly I had to file down the security pin and now it slides in but not all the way. It's a pain... for me 😅
@krisfix19837 ай бұрын
Tell me!! i know how painful can be 🤣
@gabrielasiminei94047 ай бұрын
Swirl flaps
@toppertruthio7 ай бұрын
Doesnt the new barrel and key have to be programmed into the vans computer.?
@krisfix19837 ай бұрын
Maybe new ones .not this one .this is vauxhall /opel Vivaro 2012
@toppertruthio7 ай бұрын
@krisfix6794 OK thanks I have this problem and mines a 2oo4 so I'm guessing it'll be ok
@erichaynes80607 ай бұрын
new blade old fob@toppertruhio
@radiorocksolidradiorocksol91127 ай бұрын
can you explain, my barrel just stopped turning today frost ?
@toppertruthio7 ай бұрын
@@radiorocksolidradiorocksol9112 your comment doesn't make sense
@user-dh4us5rs9e7 ай бұрын
How do you see fuse for radio because those fuse have numbers
@davidrutherford33459 ай бұрын
No need to take off the glue bottom panel. Get your hand in and push the connector to the left itll come off the panel and the wires are long enough to pull out and connect the plugs outside the panel. Then just push them back under.
@krisfix19839 ай бұрын
Thanks mate
@AndreiHanceariuc9 ай бұрын
Is this an eazy job? Can you replace them without dismantling other engine parts? I have the same noise on one of my friend's car
@krisfix198315 күн бұрын
Sorry for late reply..easy if you done this before. But you need to remove some parts
@aussieninjatv1529 ай бұрын
got same noise on my Z14XEP, does the noise get louder when you give gas and fades away when on clutch?
@howwwwwyyyyy10 ай бұрын
Slave cylinder on a td4 is inside the bell housing, well done land rover
@howwwwwyyyyy10 ай бұрын
Nice one, tells me in the Haynes the whole system is sealed and doesn't tell you where the slave and master cylinders are
@grimreaperbadboy11 ай бұрын
Swirl flaps knackered?if it is take vacuum pipe off the valve put a screw to block the vacuum pipe
@krisfix198311 ай бұрын
Hydraulic valve lifters mate this was the problem. There is a video posted with the problem..swirl flaps was removed and all checked
@bigdickdarra3372 Жыл бұрын
Romanian power yes mate asa e
@krisfix19837 ай бұрын
😅😅
@adrianprime6294 Жыл бұрын
What's the water bottle filled with, brake liquid or?
@krisfix1983 Жыл бұрын
Yes mate.brake fluid dot 4
@adrianprime6294 Жыл бұрын
@@krisfix1983 thanks
@howwwwwyyyyy10 ай бұрын
Water water 😂
@isbath Жыл бұрын
Hi, i have tapping noise on corsa d sxi 1.4, only happens when warm. Cold it's bareable, but when it gets hotter starts getting worse.
@krisfix1983 Жыл бұрын
Hi..add some hydraulic lifters solution and drive it .see of something is changing.
@isbath Жыл бұрын
@@krisfix1983 Hydraulic Valve Lifter ?
@krisfix1983 Жыл бұрын
@@isbath yes .if not working needs replacing
@runeliinteriors1612 Жыл бұрын
Go and buy *Valve Concetrate Lifter* throw it in the oil and drive abot 20mins it will fade away instantly
@krisfix1983 Жыл бұрын
To late for this mate
@bikerlad3138 Жыл бұрын
It doesn’t at this stage I tried it in my Z10XEP noise only went once new tappets and chain installed
@sweetsweet-wi1ih Жыл бұрын
Trying to find out what fixed it?
@sweetsweet-wi1ih Жыл бұрын
Can't find the other video?
@krisfix1983 Жыл бұрын
Unfortunately the customer decided to leave the car and buy another one ..sorry
@vig_Indomitable Жыл бұрын
Does this model have bluetooth?
@krisfix1983 Жыл бұрын
No.after 2011 shape probably
@vladimirstojanovic9664 Жыл бұрын
Is this knocking noise only on cold start or not?
@krisfix1983 Жыл бұрын
Permanent
@sasaberec8679 Жыл бұрын
Do you know where is right window fuse located ?
@krisfix198312 күн бұрын
Find a fuse diagram for Mercedes vito and you can find the location
@mattkemp1902 Жыл бұрын
Just picked up a 2015 corsa, makes a slightly less aggressive noise than one in the vid you put up the other day. Is this 1.4 the same as the one in the other vid where it's running and clicking away? It sounds like the injectors in mine, rather than valves (hoping anyway). Cheers
@krisfix1983 Жыл бұрын
Hi mate...First remove top cover and move the lifters one by one and if you see play on them be sure the noise is coming from there..remove the cover , coil pack all bolts around and check .if everything is OK there and nothing is playing check the intake manifold swirl flaps. You can see a vacuum on right side with a pipe on it .that one adjust the swirl flaps in intake manifold. If the noise goes away problem is from there .please send me a video if is possible.noise can come from injectors as well if not to loud.
@mattkemp1902 Жыл бұрын
@@krisfix1983 Thanks, great advice. Will have a play and take it to the garage if I get stuck
@paragoninternational705211 ай бұрын
I have same problem Corsa D 1.2
@krisfix198310 ай бұрын
@@paragoninternational7052 this is a common problem on this engines.1.3 diesel much better
@Mattlawton-ft6ew6 ай бұрын
No i think yours is normal they do click abit
@riesszbeast5241 Жыл бұрын
i have same problem with my astra. i’m waiting for next video to see how to remove lifters.
@krisfix1983 Жыл бұрын
Hi .really sorry but the customer didn't want to go further to be fixed. Soo no video
@DanSmith276 ай бұрын
@@krisfix1983I have one fully broken and rocker hit into spark plug well, so got to repair hole and replace. I really need advise how to take out cam without taking entire chain off
@krisfix19836 ай бұрын
@@DanSmith27 unfortunately you need to take the chain out to remove the camshafts. You need a blocking Timing tool find on ebay around £15 and you can remove the chain without problems
@DanSmith276 ай бұрын
@@krisfix1983 ah I thought I could lock the sprockets at top and take the one cam out, it’s the exhaust side, that sucks!
@krisfix1983 Жыл бұрын
Customer bring this to me today with this famous ticking noise . First of all this is the most common problem with this engines . This noise is coming from injectors area soo is nothing to do with lifters or timing chain Follow this steps to find the problem: 1 .check the timing chain just to be sure there is no play or noise on it 2 .check intake manifold swirl flaps 3. Check throttle body 4. Injectors 5.egr valve 6. Ignition coil pack and sparkplugs Soon next video to find the problem and sort it .suspect injectors and order part for it I hope this helps HIT LIKE AND SUBSCRIBE BUTTON FEEL FREE TO ASK .I AM HERE TO HELP .GOOD LUCK GUYS 👦
@thedigicoach5098 Жыл бұрын
Yes but how do you access it to look and change the correct fuse?
@SIMBA-gd9xu Жыл бұрын
How do you open the bonnet or hood
@krisfix1983 Жыл бұрын
Hi mate..passenger side under glove box left close to door ..pull it .most of them red colour
@gantoniom9615 Жыл бұрын
You are the Best You You helped me alot 🙏🙏
@krisfix1983 Жыл бұрын
Thanks mate
@LA-zw3jw Жыл бұрын
Hi where can we locate the ECM please computer
@krisfix1983 Жыл бұрын
Hi..I will send you a photo with location
@lazharzhari93902 жыл бұрын
Ou fusible d'affichage vitesses au tableau Vito 111cdi svp
@krisfix198312 күн бұрын
Search fuse diagram Mercedes vito and see wich one is it .thanks