Just cleaned my gun for the first time! Thanks bro! Easy and made me more confident lol

nice video and amazing cleaning gear. But according to SIG you mounted the spring the wrong way: the open side of the spring faces the guide rod. (video link for reference: kzfaq.info/get/bejne/pruGabeQrKiahKM.html) if you have the open side fazing the muzzle side , you risk pushing it through every time you mount it.

My Kimber 1911 stainless is super rigged. I regret getting this gun what a disappointment

Is it made in 'Merica & does it have a lifetime warrenty?

As a first time owner, I appreciate you posting this.

I want that bundle you got how much did it cost ? In total

I like your set up. Want to buy one.

Good job but be a little more specific.... even the smallest error or misplacement can cause a nightmare...... like the quick vid but maybe just put 10 more seconds in for details 👍

There's better and easier way to clean a gun than this. And I never leave excess oil on the gun, UNLESS I'm storing it long term. That was too much oil left on the barrel.

Seriously 255.00 for a gun cleaning mat. By time your done buying all your stuff in the video you can buy another gun

What a horrible design, SIG is way better.

I’m 12. My dad bought me an 870 for my birthday. This is really informative. Thank you a lot.

Amazing instructions and to the point.

so what did he use to clean the piece? CMP, SLP, CLT I missed it

Nice, straightforward video! Thanks

How much is it currently??

Where did you get that pad, pouch??

Don’t forget to remove the choke tube and clean the treads and then apply some choke tube grease on them and reinstall the tube. That way it won’t rust in the barrel and you’ll never be able to remove it.

Awesome video !! Thank you

Do I use the same technique for a 9 mm

Is the guide rod plastic vs. metal? Thanks.

I have a problem. I racked it. Pulled the trigger. Pulled slide back some. Pulled down on takedown lever. The recoil rod slid forward. I accidently go of the takedown lever. The gun locked. I can't rack it. I can't pull the slide back. It is frozen. Any suggestions?

Bruh pushing in the tabs still won’t release it

The video will forget to tell you your probably gonna fight the assembly link for over an hour. Getting that lined up for the pin to go in is literally so hard. It just flops around with nothing to hold it. So you just kinda pray I lines up. If your unlucky like me you’ll be spending an hour or more putting it back together.

You made it easy, thanks very helpful

sponsored by CLP.

Next time can you please talk faster.

I have a brand new Remington 870 field master I have only shot 7 target loads through it and I went to clean it and the patches keep on coming out a brown color and I let the break free clp set for about 25 minutes and I repeated this for 3 times and they are still coming out brown I used the bronze brush in between the patches and it doesent help but I looked inside the barrel with a bore light and it looks completely clean

I just bought a Browning citori cx white. My manual calls for grease to lubricant the hinge pin and locking bolt.

How do you clean the gun cleaning tool case?🤔😉

CLP in the firing pin, or in that general area?! Not good!

Exactly what I was looking for! Thanks

The best tool to clean any firearm is baby wipes. I'm telling you!

How to clean inside buckstock ?

I'd strongly argue against lubing a Glock as shown in this video. A Glock is manufactured to essentially run just about dry. Over lubing or greasing will cause fouling build up that will eventually cause trigger issues. It will also void your warranty. Follow Glock lubing instructions to the letter for optimum performance of your firearm.

You might want to mention that when replacing the spring that the curved end goes down into the recess of the barrel and not the flat side. Very thorough explanation, thanks!

Thanks... My dad always recommended looking on KZfaq to review how to clean a gun, even if you've done it before. I'm gonna admit that i've been remiss in deep cleaning my Browning Lightning sporting-clays edition Citori that my dad got me when I was finally serious about skeet... He passed away in 2021, sad to say I haven't cleaned the choke tubes since... oh well, it's getting done now. Not like I even shoot anymore, too busy instructing lol

my 21sf is squeaking like nuts after 100 rounds (dirty as hell ammo) using this as my tutorial

By far the best video on cleaning

2 things that ive heard mixed things on that you did in this video. I thought you werent supposed to let CLP touch night sights as itll break them, and I thought you were supposed to be careful with getting clp into the trigger mechanism since its hard to clean out and accumulates gunk easier. Just curious but wanted to know what people thought on that

I need a gun cleaning kid like that...

Love the grips on there. What brand are they?

I recently acquired a 1975 Citori and I can not tell if there are choke tubes or not. How can I tell for certain?

Might be one of the best breakdown videos I have seen, love the rolland the tray....well ok, all of the products used

Porque nomedejan enojas si están conformes ideacinformes. Aganlo defrente ya. Es verdad son de dónde viene lamakdad eso nadamás les gusta Aser. Pero nolesgista nada k les agauno porque asen caritas osebalen de uyras personas.

GREAT video!!!

Best most smooth yet informative video ever. Very professional, what a knowledgeable and articulate dude.

I got the this gun for Christmas, same color too. Waiting on 4 more mags to be delivered then will be taking it out.

Thanks

Perfect 👍🏾