Why would anyone reuse a cotter pin? I got an assortmant of 200 or so for like 4 bucks.

stuck it where?

Vanished lmaoo😂

Have you tried using an old garden hose for conduit to protect your wires?

10:35 Of course it comes out where the bearings are.

Maybe start with cleaning your yard. Do some hardscaping and plant some grass seed. Probly ought to wash the house too

Amen

I was a mailman in Northern California for 33 years. After a big storm, a camphor tree on my route was removed. I can still smell it. Yum!

The creature hungers for pine stump

Would an auger and a stick of dynamite make it easier?

Nice work.

🎉🎉🎉🎉

3 seconds with a spool gun and done. Dude spent 20 minutes and a bottle of argon for a 3 inch crack.

Where did u get the motor? Need one for my stump grinder.

And from approx 7 min onwards if the jack slips you end up with 2 broken ankles and some crushed nuts. I found the video to be very helpful non the less. Thank you.

Is it a pain in the a ?? I’m wanting to get a small boat trailer with no tittle

I'm building a teardrop on an old pop up trailer with no title. Ty for this info!

That's actually better than a bearing buddy. That distributes new grease behind both bearing and then more or less symmetrically pushed old grease out to be removed and evenly repacked with fresh grease. I couldn't personally argue for or against that symmetry in the inner bearing but if you were to pump grease you would see it come out of the outer bearing symmetrically dirty grease first. In fact its super obvious that you haven't been maintaining these. bad tread wear and no visible grease behind the rubber seal. you should start with bearing preload by shaking the wheel when you lift it and spin it. You'll git 'er done.

I wish i could find a full metal deal like that for 200$..

Tiggin! Tig on!

"Firearm or Fireworks?" We play the same game in Chicago, but not just on the 4th of July.

In georgia they aren't even title youve got 2 choices register it as a homemade trailer which the process sounds similar to here as what you're describing except they only require that you "permanently affix " the homemade trailer ID tag which becomes the VIN for the trailer in georgia the other alternative if you buy a trailer in georgia that was made by a manufacturer then you just need a bill of sale with the VIN on it

Springs are to weak or spring spacing is off….. wire worn over axle, is it bottoming out on wood floor?

I just hooked up a 30k btu duel fuel heater and the pilot lights will not stay lit after multiple tries and holding pilot control valve down for 60 secs. And still not staying lit. This means it will never light the bricks. It's going back to the store tomorrow.

For somebody that's cold you talk too much get to the point your typical KZfaq you talk a whole lot about nonsense instead of getting to the point

Nice

Nice work

Good video 👍

Replace with nylon coated cable. Vinyl coated is useless. Harder to find, and more expensive, but way way more durable.

You can just hear the engineer going in circles while designing this. "Can't be metal on metal, the cable will fray." Rubber roller. "Can't be metal on rubber, the cable will wear through." Plastic sheathed cable. "There we go, look at that problem we just created and fixed all in one sitting, sure hope the tolerances on this test sheet are wrong and the first thing to wear off won't be the exposed plastic sheathed steel wire making this whole thing a waste of time and a pain for anyone who buys it.

That finish is mid tho......

That’s because you used 1/8” tubing.. should have used at least 3/16”

Pine wins . Ya blades need sharpened everytime

Clown: “why do we over engineer things? So they break in operation” 😂

Lol typical wannabe welder trying to flex: this is why you should never trust a KZfaq tutorial. This is why my business thrives. if you’d designed this properly it would have never ripped apart. Why did you weld thick metal to thin metal, clown? I’d fire you just for suggesting that we use any less than 1/4” wall for that square tubing on a front hitch. You’re unfit as a fabricator if you think 1/8 or 3/16 was enough. You don’t own a welding shop. You have a welder and charge people for poorly made garbage. Lol wonder why none of these I’ve ever built have ever broken…

They make front tow hitches that bolt on and retain the front tow hooks, rated for 6k lbs

That motor needs all the sheet metal cover on it. The right had cover the covers the spark plugs is missing. It will run hot. The covers direct air over all the fins

Respect awesome

I think Kobalt has a lifetime warranty on hand tools. Should be able to take it in and say it’s broken for a replacement

Number one that design of shovel is actually a cold shovel, but should be made of steel. Some idiot thought they would use aluminum to make it lighter and easier to handle. However the aluminum is not strong enough to withstand the weight of most materials. Snow included. And I hate to say it. But unless it is light. Fluffy powder snow, it's gonna be heavier than those wood chips. Those shovels are garbage for shoveling snow even if it is light fluffy powder. When made of steel, that design of shovel is excellent for loose material such as coal gravel or wood chips

Try out the Bully Tools Coal shovel or the Razorback shovel of the same style you have.

There’s a difference between working hard and being a slave to your job.

How is the V465D coming alone? Did you get the PTO unit off?

How much would a job like this cost i ask because i need something like this done to my 5x8 utility trailer so i can put motors and transmision to haul away to the scrap yard?

Sounds about right lol

Sad to see a beautiful stump get ground up.

Song name please?

That's not grinding!!

Nice work

Lmao 😂This is my average day