Were did you buy the Steering shaft ? I have a Dakota like this need to replace steering shaft, and thank U vary much for taking the time to post this video.
@BigThomTattoos3 күн бұрын
Miss Mr. Jones videos 😢 I have based a lot of my Dart build off of Mr. Jones...I have the FiTech 1200 and can't remember, Do I need a fuel regulator? 🤔
@TheGasTap2 күн бұрын
You don’t. It’s in the FiTech. 😊
@Formerlywarmer9 күн бұрын
I’ve had a dozen between the two never had it even seen a cracked head. Like I say heat kills and I don’t let my stuff get hot either.
@CrOssXoVer310 күн бұрын
Ive had to replace 3 on my dakota, one of them i had to redo because it just gave out again ,maybe 2 years is what it lasted. Every time i just hear something drop somewhere and regulator is busted. Any idea what could be my issue? Read about cleaning stuff and replacing weathring etc, any video suggestions or part names?
@TheGasTap10 күн бұрын
Maybe cheap parts we have today. I would lube the window runs with silicon spray.
@dyer2cycle10 күн бұрын
How to lower a 72-93 Dodge truck..Don't!..why lower it? looks much better stock ride height, and a lowered pickup is going to bump and drag on everything...makes me both sick, and sad, to see so many of the survivors of these older trucks get lowered, big wheels with rubber band tires, and similar modifications..they'll never make trucks like that anymore, why screw them up?
@TheGasTap10 күн бұрын
Your opinion doesn’t matter to me. I love my truck.
@TheGasTap10 күн бұрын
Get off my channel if you are a negative person. We don’t need you. We are all positive here.
@dyer2cycle10 күн бұрын
@@TheGasTap Glad to get off!..with an attitude like that, you won't have a channel for long..plenty of others where folks are glad to discuss differing tastes and opinions!
@dyer2cycle10 күн бұрын
@@TheGasTap Not a negative person...just don't understand these fads...glad you love your truck...
@TheGasTap9 күн бұрын
My apologies. When you sad sick and sad, that sounds negative.
@wanderingdaze701812 күн бұрын
Been doing some research on how to lift my b series van. You think if I use the lower control arms from these trucks will give me a couple of inches of lift?
@TheGasTap12 күн бұрын
It would but the problem is the bolt size is smaller on the d series. Not sure if you could sleeve the B van holes to make it safe. I’d love to have a lifted B Van!!
@Steve-cs3tt13 күн бұрын
I have a question. If the rack & pinion is bad would it make the steering turn worse than manual steering ? Great video, thanks, Steve
@TheGasTap12 күн бұрын
That sounds like a pump issue unless the rack has bad gears. But you would probably feel the gears grinding. Probably a pump issue.
@whojackson14 күн бұрын
If anyone is having trouble getting that locknut and bolt off, just cut it off with a hyper tough mini sawzall ($40) and go to the hardware store and ask for that same bolt and nut. I tried numerous other methods to get it off but the mini sawzall was what worked in the end.
@jaysonyang144114 күн бұрын
Those street fire cdi boxes are complete junk, I’ve had two failed me and said no more! First one died before the warranty ended and replacement died shortly after
How much did you drive before getting the alignment?
@TheGasTap15 күн бұрын
Straight to the shop the next day. 10 miles maybe.
@RonaldLewis-py6yt19 күн бұрын
Nice share, we build engines daily we turn the block up side down and install the bearing aligning the feed holes next install the camshaft to make sure it turns freely then move forward!!
@user-cg9ly4wg2s19 күн бұрын
FYI those little pumps like the one on your tailgate are garbage. The outlet side is pressed in with an o ring and it can pop out easily.
@TheGasTap19 күн бұрын
I’ve been using them for 12 years. Now that I have a bigger feed line I’ve had no issues.
@tonydetailing0821 күн бұрын
Hello sir, I have a new batch of polishing machines recently. Would you be interested in helping me test them?
@TheGasTap20 күн бұрын
Shoot me an email or message me on Facebook or Instagram. [email protected]
@tonydetailing0820 күн бұрын
@@TheGasTap Got it, I sent you an email.
@williamjwarren373522 күн бұрын
Any updates on mr jones?
@TheGasTap20 күн бұрын
He’s here at camp. I don’t drive it much since it’s so hot here. I need to do an update video.
@williamfish2423 күн бұрын
Put big tire
@TheGasTap9 күн бұрын
Ok
@derekdebord1992Ай бұрын
I bought my new 18 in black max chain saw at Walmart yesterday for 91 dollar
@TheGasTap29 күн бұрын
😮
@franklinZacАй бұрын
More big red videos
@3DdemonАй бұрын
Thanks for your video. I have one of these lift. Yesterday after I unloaded my scooter I pressed the button to send up, started going up but it did not fold close. Still the thing that comes down to hold the scooter still coming down without the scooter on the platform. How do you adjust it? thanks.
@jonathanmorris8677Ай бұрын
just a question what if you want to run ac on v belt style will the cheap intakes work ?
@TheGasTapАй бұрын
I haven’t tried it but since it most resembles the LA intake, I would assume so.
@CarlosLopez-tt5pyАй бұрын
Great video well explain thanks
@williambriggs5024Ай бұрын
Ok, 3 things: 1: You need to start and end the test from the same location. You don’t know how much more downhill you were going there versus coming back. 2: You need to fill up from the same pump, start and finish. The automatic shutoff on pumps vary a lot, so stick with the same pump. 3: This stopped working for gas vehicles since they added ethanol. It still works for diesel. My old Supercharged Riviera got a 4 mpg boost on the highway with acetone. But it disappeared when they added ethanol. 😢
@tonyjohanningsmeier559726 күн бұрын
You can also increase the tire pressure to max that the tire manufacturer recommends. This info is usually on the sidewall of the tire. Another thing is to go to a taller tire, this will bring the engine rpm down when making the same speed and you will get the best results during cruise condition. Tall skinny tires have less rolling resistance than wide tires.
@BulkshitАй бұрын
Not a lot on the electrical stuff. Good but ,Basic, very basic.
@oligoonАй бұрын
useful vid - enjoyed seeing ur dog helping out!
@TheGasTapАй бұрын
Thank you!
@biblequestionsanswered6572Ай бұрын
Great instructions and helped me get mine done.
@TheGasTapАй бұрын
That’s great!! Thank you!!
@doomman700Ай бұрын
I can tell you this, make sure you have the octane covered until you nail down the requirements
@papelariaavenidaavenida1955Ай бұрын
Good Mornig teria comomandar um jogo de maquinad de vidro da dakota sport
@bryancano9300Ай бұрын
Simple video and straight to the point Thanks i subscribed and liked
@TheGasTapАй бұрын
Thank you!
@carlcarlamos9055Ай бұрын
Would the police wheels from the later Diplomats fit your car? Thanks. Take care.
@TheGasTapАй бұрын
Should. I believe it’s the same bolt pattern.
@carlcarlamos9055Ай бұрын
This is a long time after you’ve done this, but it looks like you still answer questions. Are the super stock springs wider than the originals? I know you are mainly interested in drag racing, but how does the car handle on turns, now that you have changed the suspension?Thanks much and take care. Hope you have good results with that car.
@TheGasTapАй бұрын
They are the same width. They are pretty stiff. They ride good. I have a little tire scrub in corners. The tires barely fit.
@RobbyRoss-ng4dkАй бұрын
When you reinstalled the cap on the back of the motor, how far did you hit it in? Do you take it as far as it can go? I'm doing one myself and not sure if it needs to contact the cam or sit flush with the outer edge of the block
@leonelplascencia2990Ай бұрын
Really nice truck
@TheGasTapАй бұрын
Thank you!!
@j6collins914Ай бұрын
I just did mine with a cross measurement that was off by 3/8” is that acceptable?
@TheGasTapАй бұрын
Give the manufacturer a call. You will have a little alignment issue but I’m not sure if you are in tolerance or not.
@poopooboudreaux12 ай бұрын
What is the cross tube called and what does it do? Thanks!
@TheGasTapАй бұрын
It’s just an air crossover since the boots are sealed.
@CraftyRoseDentalinstructor.2 ай бұрын
I got a saddle cover that the sun broke down in less than a year ........ sadly that is the reality .... the good old time quality is gone forever...... they call it progress the one i got to AVOID is one that has black stretch like nylon that wraps over top of seat and head rests..... who needs head rest for bench seat????.... i still have the old one from 20 years ago under neath as filler ...... the newer ones are junk and they wont last . be sure you get the right size 3 sizes mini truck , mid size and full size using a Mexican rug is a good option... more work but it will last 10 years ,,,,,,,,,,,,
@jeffbonner18692 ай бұрын
I just bought a FITech unit and noticed that the TPS sensor housing extends below the gasket surface of the throttle body unit. (about 1/16 inch) So, if the unit is bolted on right out of the box, the TPS unit will be distorted unless you notch the base gasket to allow clearance for the TPS housing to "hang down". This could explain why you had a fast idle (TPS not allowing the throttle blades to return fully) and why the TPS percentages are off. (distorted housing) I took my Dremel and ground the TPS sensor housing flush with the base surface of the throttle body. I have not tested it yet but expect no issues. I also alerted FITech of the issue. Just say'in
@legofreak888844442 ай бұрын
Etelbrock or Huegs sell an intake manifold for the magnum
@user-tr2cx7kb1l2 ай бұрын
How the fuck you get all that,,never mind
@user-tr2cx7kb1l2 ай бұрын
Im new,good stuff ,im with you,real time
@user-tr2cx7kb1l2 ай бұрын
What are you putting in ,rx7
@TheGasTap2 ай бұрын
Planning on a turbo 360.
@user-tr2cx7kb1l2 ай бұрын
Or better
@user-tr2cx7kb1l2 ай бұрын
Oh your trying to run 9.00s
@user-tr2cx7kb1l2 ай бұрын
Yo cool shit
@voodstoc2 ай бұрын
Thanks so much for showing this! Saved me so much time and headache.
@TheGasTap2 ай бұрын
That’s great!! You’re welcome!!
@Moparmojodojocasahouse2 ай бұрын
Cool
@steveburlingame19352 ай бұрын
Wats your horsepower
@TheGasTap2 ай бұрын
Est. 440
@CHARLESTHOMPSON-rv4gn2 ай бұрын
4 min into the video and Im already seeing im MISSING PARTS DONT BUY !!! DONT BUY !!!!!!
@TheGasTap2 ай бұрын
I’d recommend contacting the manufacturer.
@CHARLESTHOMPSON-rv4gn2 ай бұрын
printed instructions sucked.. all the parts just came in a bag ,, very dissapointed.
@amariodom48582 ай бұрын
i wish my fuel pump was that loud… let errbody know who’s the boss haha
@brandonyoder332 ай бұрын
I’m just wondering where you found the entire vent window assembly, I can’t seem to find any for my 87 V25