how would you know how much refrigerant to put in there if you don't know what's in the system presently? to properly do this job, it requires a machine that will pump out all the refrigerant and then put in what's in the spec for a particular vehicle
@markpwebbКүн бұрын
Thanks man!
@brianolllo3 күн бұрын
Hey man thanks for the video but quick question. My 2003 Ford F-150 Air Conditioning works but it doesn’t give out cold air though, only warm. Is there anyway that I could maybe fix it?
@TheDonutman446 күн бұрын
Hey thx a lot Sir! Switched mine out thx to your easy video to follow! God Bless!👍🙏
@justinbrown46227 күн бұрын
I honestly didn't know that caliper pisten screwed in and out. I've always had and worked on cars that were just straight in and out. I popped the brake reservoir lid off and just used a flat screw driver to screw it back in. Went smooth. Thank you.
@Xddtakataka8 күн бұрын
Is it Better sintetic blend or full sintetic?
@gunwrites622213 күн бұрын
I can do the work, just could not make the videos. I'd have to edit out too many old Anglo-Saxon words!
@thomasfixit79317 күн бұрын
lol
@donnachandler992117 күн бұрын
Should have cut the line short then use a socket
@christiana691718 күн бұрын
Awww Glove? Cute
@brun031918 күн бұрын
How much was it at Honda?
@sithtony44911 күн бұрын
Like 15$ for my civic probably the same for the accord
@markvankoughnet123621 күн бұрын
what kind of epoxy did you use?
@normanjannisch875225 күн бұрын
Just had this happen on my 5th wheel trailer. com Turns out myGMC has a 20 amp fuse in the main fuse box under the hood. I changed the fuse and now have marker lights again
@codyisarat27 күн бұрын
Just did the same job on my 08 f150. However, the rotor/hub assembly would not turn very freely after being torqued down. The passenger side rotated perfectly free as yours did in the video. Any ideas why my driver side will barely spin once the axle nut is torqued to 300ft lbs? Both sides were tested without brakes installed. I did use a torque wrench. Not an impact.
@Nunya-_-26 күн бұрын
Pretty sure the actual spec is 296 but not sure if torquing it to 300 would cause problems like that
@codyisarat13 күн бұрын
@@Nunya-_- nah it ended up being a bad wheel bearing out of the box… thanks acdelco😂 new rotor/bearing installed and spins freely.
@thomasfixit79317 күн бұрын
Glad you got it replaced!
@tbone692427 күн бұрын
Thanks for this...I have replaced tons of brake pads, but it has been over 10 years ago now, so it was nice to get a quick refresher without having to waste time on a 30-minute video.
@thomasfixit793127 күн бұрын
Glad it helped!
@jackwixom604929 күн бұрын
Mines is burnt out on drivers side too
@Adub86Ай бұрын
Three different bolt sizes??? Uhhhhggg fooooorrrrrrrddddd!!! Whyyyy!!?
@nickv4073Ай бұрын
Practically no one bothers with removing the little drain plug on the oil filter housing. I never do. If it ain't leaking, its fine. Just go straight to removing the entire housing. Save time.
@anthonymagee5725Ай бұрын
My cpu is telling me to check gauges so would thr pcm be an issue?
@jerrymiller5978Ай бұрын
My passenger side brake light was not working. I sprayed contact cleaner on the rv plug and truck connector. That did the trick. Thanks!
@thomasfixit7931Ай бұрын
Good to hear it was an easy fix
@Pound4Pound23Ай бұрын
Thanks
@thomasfixit7931Ай бұрын
Welcome!
@texomatinker414Ай бұрын
I got mine done and have a tip to share for getting the bottom cover back into the steering wheel assembly. Looking at the top of the flange that needs to be inserted, notice the excess of flange beyond the hooks at the top. Leaving the hooks, cut off the excess following a line that will leave only half of the flange at the bottom. It will then snap into place easily without compromising the integrity of the piece.
@thomasfixit7931Ай бұрын
Thanks for the info!
@jamesfukai6064Ай бұрын
The engine cover bolts are different on the front and back do you happen to know which ones went which way?
I drove a 1997 ford f150 4×4 stepside with a 4.6 engine for 475k. Regular maintenance and motorcraft semi synthetic oil every 5k mile. Tranny started to shudder and blew a head gasket after 15 years of driving out of state to work.
@thomasfixit7931Ай бұрын
475k miles is awesome!
@texomatinker414Ай бұрын
Great job! You do better with one hand while shooting video than I'll be able to do with my 76 year-old mitts, but you've convinced me I should be able to get the job done without pulling the steering wheel. I really didn't want to mess with that.
@thomasfixit7931Ай бұрын
You got this!
@johnnybolen5701Ай бұрын
Thanks for the video, my light was on, and when I give it gas my Air conditioner would stop blowing. Many thanks for your video. I will have to con my son into fixing it for me.😂
@thomasfixit7931Ай бұрын
Sounds like a good plan!
@tenthousandwordsАй бұрын
It's $280 if I ask our local small engine mechanic to fix it. Now you have restored my faith in myself!
@thomasfixit7931Ай бұрын
You got this!
@tenthousandwordsАй бұрын
Every year Thomas has to teach me again how to do it with the correct tools. Thanks!
@thomasfixit7931Ай бұрын
Glad I can help!
@essiecoolman2738Ай бұрын
Really good job explaining thank you
@thomasfixit7931Ай бұрын
Thanks!
@BumpingNastysАй бұрын
Great. Love youtube
@javierochoa432Ай бұрын
For those people wondering why they keep replacing their alternators it’s bcuz of the amount of oil leaking into the alternator I had the same problem
@melodysellАй бұрын
Thank you for this video! My alternator has that same grease caked all over it. Did you find out what leak caused it on yours?
@The495marauderАй бұрын
I’m getting uneven vent air conditioning temperatures. The passenger side seems to be fine. But the drivers side is blowing warm air. My drivers side actuator goes up smooth and effortless for heat however for the ac it goes down far enough for the air to blow but hesitates and stops. Does that indicate that it’s stuck and the actuator is bad???
@thomasfixit7931Ай бұрын
You may just need to charge the a/c system. Check out my other a/c video
@joefabela9267Ай бұрын
Gonna try this and I'll come back to let ya know if it worked 😅
@The495marauderАй бұрын
Any updates? Which car are you the replacing the part on?
@straydawg461Ай бұрын
I have a 12' PJ utility trailer that on drivers side the front running light on trl. and the running light on its front fender do not light up with two different vehicles. All the other running lights work on that side and other side including rear lights function. Do I have a ground problem or wire problem? Any advice?
@thomasfixit7931Ай бұрын
So half the running light work on one side?
@straydawg461Ай бұрын
@@thomasfixit7931 Yes the very front drivers side marker light and the front marker light on the wheel well fender don't work. But the DS rear wheel well marker light on fender and DS rear marker light and ALL the other lights work. So 6 total out of the 8 side lights and all of the other rear lights and blinkers work.
@KeshabOli-rz8mcАй бұрын
Very useful, thanks
@thomasfixit7931Ай бұрын
Glad it was helpful!
@bluyetiinc7553Ай бұрын
Great video. One of my turn signals is blinking really fast. Is it likely to be the connector?
@thomasfixit7931Ай бұрын
standard bulbs or LED?
@brianfletcher7449Ай бұрын
Could you use a floor jack to pry the swaybar up? Have a 2001 F150 I got from my dad when he passed a couple years ago and the linkages need to be replaced.
@thomasfixit793127 күн бұрын
You shouldn't need to
@guyandottewhiskers2331Ай бұрын
All my lights work except for left break light I’m stumped
@thomasfixit7931Ай бұрын
Did you change the bulb? Sometimes it is bad, but doesn't look blown
@JamesNichols-uh8zk2 ай бұрын
I just changed mine on a 2008 f150 4.6 liter i did not need the tool for the fuel line it had a clip on each end that holds it in place
@cyrusdiaz95222 ай бұрын
I love you
@emoneyblue2 ай бұрын
Perfect, how to video thank you brother. I just finished mine with your help.
@thomasfixit7931Ай бұрын
Glad it helped
@ashleykuchta19482 ай бұрын
Yes I have
@mdbassin62672 ай бұрын
good video - noticed my bow light was not working last night - pulled it apart and the cap on end of bulb was separated - ordered some replacement LED off of amazon
@thomasfixit7931Ай бұрын
Thanks
@lc54942 ай бұрын
watched many videos on this topic, but this was the only one that clearly showed a trick to install the spring/hose clamp. Thanks a lot.
@thomasfixit79312 ай бұрын
Glad it helped!
@1heavyelement2 ай бұрын
thanks brother. you are the only video i found where a smoking solenoid is mentioned. my mower is 8 years old. i'm just replacing the whole carburetor. p.s my mower is a poulan pro 17.5 HP which is made by husqvarna. just an fyi if anybody in the future reads this.
@thomasfixit79312 ай бұрын
Welcome! Glad the video helped!
@MsReed-wx2ho2 ай бұрын
Thank you soo much
@thomasfixit79312 ай бұрын
You're welcome!
@JuniorWarrior4Christ2 ай бұрын
Thx you my Brother , you save Me some $$ to replace ! 👍
@thomasfixit79312 ай бұрын
Welcome! Glad to hear!
@ebayhlf2 ай бұрын
When you put the hub back on after installing the new bearings and seal does it take alot of pressure to get the seal back over the seal surface? or does the seal just rest against it? im having hell trying to get it back on i ripped the rubber off the seal trying to get it back on...thanks