I ran into this problem on *2* of these GE dishwashers today! One was consistently giving a “FTD” Failure to Drain code mid-cycle, and the other was giving an “H20” code when it began filling at the beginning of the cycle. Both were fixed by following your instructions! I found the FTD-problem sensor just had some crud inside the white elbow part and some crud around the black part. H20-problem sensor had a whole bunch of gunk nearly clogging up the white elbow part and lots of stuff around the black part. Cleaned both completely and both started working! Didn’t need to replace either of em! A tip: make sure the black piece snaps back into the white piece. It will leak if you don’t…! Great video-thank you for making my day as a tech much easier :) A tip to anyone reading this-use LESS detergent if possible. Avoid pods, use powder and don’t go overboard at that. I’m convinced excess detergent is behind this problem to some degree…

Does this work on a 2019 CX-5?

How to install more? All apps in the tweaks.

Thank you this is exactly the video I needed 👏

I'm on 70.00.100A in a 2019 Mazda CX5 and I'm confused about the "firmware must be updated before installing the updated USB hub". Do I only need to update the firmware to 74 or is there something else I need to do?

To bad they dont make these a little more powerful, because they are so quiet its nice to use without hearing protection.

I used canola spray and tapped with a rubber mallot lightly. Worked very well. Manageable enough for this small lady to do by herself

So I just did the rear coils and it took about 3 hours with a break in the middle. I removed the throttle body so I wouldn't have to disconnect the coolant lines going to it. The only difficult thing I found was get access to the EGR valve bolds so used a 1/4 socket with a wobbly with a 1/4 extention through the break valve pipes with a second wobbly and adapter to a 1/2 ratchet. Pretty easy overall.

2018 chevy spark manual transmission, while replacing the shifter cable i noticed the lever at the top of transmission is loose. And infact was not the shifter cable at all. I manually put the lever into 1st ,2nd 3rd,4th,5th but none of the gears seem to engage.With engine off. Any ideas what it might be?

This worked!!! thank you!

So, I think I can do this but I want to clarify that it is important to have the engine off during this process. I just don't trust my battery enough to last 20 minutes- up to 40 minutes. So I'd much rather have my car run the entire time, rather than have it shut off mid-update.

2004 galant same location?

Perfect video! Thank you!

What if it’s stuck in the open position? Having a hard time figuring out how to start the up adjustment from the down position while keeping the door engaged to the opener.

I just ordered the 18 pod kit and had no idea what do when it arrived. This video and the comments have answered so many questions I had. Thanks so much! I'm looking forward to getting started very soon!

Will this work with version 70.00.335?

Killobyte, thank you for putting to this test. Just wondering, have you experienced any undesirable or unintended consequences to making this change? Did you backup your existing firmware prior to making this change in case something went wrong during installation? I'd hate to have to go hat in hand to the local Mazda dealer to have them fix problems.

So since you clearly know, nothing about growing anything the light settings are not for fruits, vegetables, and flowers. It’s for vegetative growth, and fruiting and flowering process of growing.

16 and 12 works nice with wheels and 2x4's Started the evening looking at the price of portable scissor lifts. I know what I'm doing in the morning.

Is that stock height or has the ND been lowered? Beautiful ND btw

In your opinion do think the product maybe clogged with buildup?

Thanks for doing this, works great! Have you tried any of the other toggles? Would like to be able to read text messages at speed and not seen if enabling touch screen will allow this now.

Soft top may be problematic for people with shoulder pain.

Hola, existe versión 74.00.324 ADR, será posible que la tenga?

Too much pad stall.....not recommended

Thanks! Not washing the dishes by hand tonight, and grateful for it.

Thank you very much. I have been chasing an oil leak. I just found that its coming out from under the dist. I think its bottomed out and there's a gap. I will now shim it then install a new gasket. Instead of just a new gasket. Then I can finish my work on the advance curb. Thank You

Hello, thanks for the video, I didn't understand if I can upgrade my 2021 ND 2.0 in Italy with the link in the description... thank you

So good. I have a matching 2019 SRC RF club, and I followed your instructions and updated this morning. Drove the car around today for a bit just to touch the screen. Works with stock interface and Apple Car Play perfectly. So simple. Such a huge change. It’s hard to explain how significantly this one little update-which was easy to do-improved an already incredible car. Thanks for posting it all!

just wonder to know will it works if not upgrading the firmware? existing runs 70.x

If anyone tested this procedure with 70.00.367 EU N, let me know.

Soft top baby! Less noise with the top down. I think I would have built the RF as a coupe, it’s a sexy looking thing, but ST for me every time, it’s cheaper, lighter and they are built for top down, it’s a sports car and opening and closing done manually is the way to go. I had a Boxster S with motor driven soft top, give me the manual version every day. Good honest video, I don’t think security is an issue, if somebody wants in, they get in, but yeah a soft tape needs care and storing outside means it needs more than if you are garaging it.

Excellent. Has there been any updates on a way to disable Gracenote?

Thank you! So far so good. Saving so much money!

So can you use the touchscreen at speed with Apple CarPlay and Android Auto as well?

Two gens of soft top - garage = RF. Just do not like the bulbous look of earlier hard MX tops.

Hi there, thanks for your video. I just bought another MX5, 😂 an ND3 ST. Do you avoid any rubbing or clearance issues with the tyre sizes you are running?

Leather grip to turn helps.

Mine was jamed and required tools to open. Sst wool in lil baffle. Going in with new pcv.

You will have to drive my car next event! Great seeing you 👍

Just so you know, this video is still very relevant and helpful. The replacement process of a hot cartridge on a 25+ year old faucet that still looks like new was a challenge because the cartridge was exactly like this one rather than a newer cart. shown in most of the other videos, including one on the Fister site. Fortunately, others had mentioned the swap of the old brass fitting on the new cartridge but the supplied instructions were very incomplete. Finally figured out using the new upper and lower gasket and got the job done. Found this video after the fact and appreciate the validation that I was on the right track. For others who may need help with part numbers on older PF faucet/cartridges, the Fister site will identify model names and cartridge number of older models not archived in their search database if you send a pic of the faucet.

We have been struggling with this for weeks and I came across your video Happy to have a dishwasher full of clean dishes again! Thanks so much!

i don’t understand the wiring

Great video, instructions worked flawlessly on the '20 MX-5 RF. I am interested in your comment on being able to enable touchscreen while moving. Waiting for that video!

One very important thing you did not mention is Driving visibility that soft top wins in this category as well.

I was dead set on the RF for a few years. Yes, years. Now that I'll finally be getting one in January 2025 (hopefully no big news on 2025/26 models), I changed my mind about a month ago and will likely go ST because of the classic feel and look. I've been waiting for my daughter to graduate from college as I'm helping her to pay for everything and she will graduate in December so I'll have the freedom to go Zoom-Zoom old style.

I have a 2018 cx9. Can you help me please?

Thank you for the instructions. I'll have to upgrade it. My 19 Mazda 6 is on firmware 70.00.200 ΝΑ N and it reboots itself pretty often and Android Auto doesn't always boot either

sir, this video was pricelessly helpful. i watched literally 3mins and 1sec and my marriage was saved! 😅 thank you so much, and may GOD bless you abundantly!

So what abbot cars in Europe?