A hard stop is more accurate, a dial does not account for bearing clearance, which is taken up by compression !
@eaglehyzer38293 ай бұрын
Well, hmmm I'll take that in consideration and run that across to Johnny .. What I can say is that process has shown lots of horsepower on the dyno over the years ..
@henryserrano651010 ай бұрын
Why when finding TDC at degree wheel 19.5 degree, the piston is below the deck surface and is use as reference ?
@MiGG_Aus Жыл бұрын
Is this the same for twin cam engines?
@richardrichard4394 Жыл бұрын
Reher Morrison the best, impressed they have some video's, loved when they had Tech on CHP magazine always correct but not many secrets Airflow that's the ticket Thanks for this stuff
@markochs2495 Жыл бұрын
As good as it may sound. Those 56 Chevrolets did not move that quick
@joeylee6422 жыл бұрын
I wish i could get the pdf file to print those cam pages to write down my measurements
@shaneshane13792 жыл бұрын
Damn fools! That 265 aint small bore. Just short stroke. 😋
@nitrofumes20122 жыл бұрын
At least the ‘56 had a real oil filter. Wasn’t a spin on yet but those canister filters were pretty good. The 55 had that add on filter on the top of the intake manifold.
@frednichols29782 жыл бұрын
Thank you for showing the example for us visual learners.
@mikef-gi2dg2 жыл бұрын
I can hear the only an LS will do crowd saying.....FAKE NEWS!!!
@mikef-gi2dg2 жыл бұрын
HELL YES!
@johnshackelford69652 жыл бұрын
Sherly Muldowney The Californians Discount Warehouse
@thedobermangang35032 жыл бұрын
got a question for u my brother....i got 1990 k5 blazer 5.7 just got the enging rebuild still have the swirl port heads on it and its pretty mush stock i have high perfomace intake im eliminating the computing trying to make my mine up if im going to go with a carb or some efi sniper..i have 700r4 trans and 4.10 gears and up graded my torque convert to a 2000 to 2400 stall ..it has a up grade cam in it howard cams ratter 188005-09 lift .525/530 and duration .050 ; 227/235 centerline 103 i want to no is that a good cam to go with them swirl port heads and would i be able to hear the cam..i dont no to mush about cams..i no the vortec or aluminum heads would have been better but the engine was already build already..i do have headers 3 inche pipes all the way back
@cecilandrews74792 жыл бұрын
I would like to see an engine on the Dyno with timing dot to dot. Then degree the Cam To see what the gains are if any.
@richardrichard4394 Жыл бұрын
All depends on the accuracy of the cam when CNC''D Advance or Retard and engine output and being R&M sky the limit
@fairytail69392 жыл бұрын
advance 3 degrees
@elinino52753 жыл бұрын
Reher-Morrison😲😲
@sweetness34km3 жыл бұрын
Beating it up
@kevinhuneycutt96913 жыл бұрын
That's a burnout.
@barnabyjones51613 жыл бұрын
Perfection
@appalachiancookingwithbren14113 жыл бұрын
what did you put it in -- like to see some more.
@ER-dj3bw3 жыл бұрын
Hi, would that formula work with a 4 in line Kawasaki ZX7R motorcycle engine? Great video!
@eaglehyzer38293 жыл бұрын
I would think it would , you might call and talk to Johnny a Reher Morrison and see what he has to allow about it ... 817 467 7171
@rayadouno78113 жыл бұрын
Man this was REALLY GOOD, I wish he had closed with a more detailed explanation as a conclusion. Being a first time for me, it leaves me thinking what next.
@strongme804 жыл бұрын
So which way do you turn the adjustable camshaft gear if you find the lobe centerline being off based of off the cam card? This video didn't really explain that.
@TheRoadhammer379 Жыл бұрын
clockwise
@garrettcarpenter33194 жыл бұрын
I dont know that engine sounds alot bigger than 265 with that small of bore and stroke but it might be due to the dual carb settup and camshaft setup it sounds wicked
@johnnymula23054 жыл бұрын
Ive seen a few how to degree a cam videos. This ones the best in giving full detail on setup and procedure. Thanks!
@joeestes81144 жыл бұрын
Awesome video! Thanks for sharing!
@inthefastlanebro4 жыл бұрын
I need it
@charlesmartin73474 жыл бұрын
This was a good video and I'm not complaining but next time backup the camera so we can see everything the dial gauge and the wheel and the direction of the man turning the wheel . Leaves out the guess work for dummies like myself . I'm visual so I can mimic what you're doing. But thanks for sharing your knowledge. Blessings and more Blessings
@MrFredsAdventures4 жыл бұрын
I'm new to this stuff...trying to learn. It looked like the piston was not all the way up at TDC. Is the angle or am I missing something?
@raymondpanzera87104 жыл бұрын
You are correct , the piston is not truly at TDC ,you take the measurement just before/after the piston reaches TDC because of piston dwell....every engine has piston dwell , that amount of crank degree can vary greatly. which is why you take the measurement just before and just after
@raymondpanzera87104 жыл бұрын
Way better video .kzfaq.info/get/bejne/a99-Z7Gq0su5ZWw.html
@CallofDoobie5854 жыл бұрын
❤️
@superfuntime31074 жыл бұрын
They had the goods the whole time back in the day.
@superfuntime31074 жыл бұрын
1:34 Could you explain that differently ? How is the locating dowel position relative to the base circle of the cam lobe determined ? Is it installed before grinding ? I would think yes as it would act as a dog to spin it between centers yes ? I should watch a video on how a cam is made.
@GG-rj4oj4 жыл бұрын
When the cam is made , the dowel is installed prior to the cam being ground. A drive is fixed to the dowel end. The cam grinding process / profile is then completed. The dowel is the datum. You sometimes read the cam is ground 3deg advance. In that case the drive end (usually supported in a chuck) is then clocked the 3deg and the grind process begins. I hope this helped.
@StormCentre885 жыл бұрын
Nice N Nasty
@joeblough705 жыл бұрын
Always quality at R&M. Straight shooters & powerful machinery.
@appalachiancookingwithbren14115 жыл бұрын
hell yea.
@davidh12495 жыл бұрын
858 horsepower from a naturally aspirated 436 cubic inch engine That is impressive to say the least.David Reher and the guys at Reher-Morrison really know how to build a high horsepower bullet.
@realbass43025 жыл бұрын
what a bad mother shut your sweet
@fordsaretampons6 жыл бұрын
What did it make?
@eaglehyzer38296 жыл бұрын
It made a little over 550hp....
@rudydog4206 жыл бұрын
Wow! 550 hp out of a 56 265? I just bought one same year with mild cam headers duel quad carbs 500. Not sure what alse has ben done to it yet. I wonder how many hp I will get out of it I'm guessing 275 ish??? What do you thank? isn't the corvette motor.