A few disables lower and I'd think this was hank hill

I recently just drained mine but when I closed it, it still drips a little bit any advice?

Hi ,we need leather cutting machine

Very helpful. I just bought a 5 in 1 that I’m restoring.

Hu I got a compass 2014 it's been very good until last year now the steering and breaks feel sluggish and sometimes feels like the car is pulling like half a ton with just me in it

I repaired this with an AO3416 mosfet. Works like a charm so far. Hope it helps others, this mosfet is cheap, it would be a shame to throw away your shaver.

Needed this !!

I have this. Never used it. I’m glad to see your vid. Ty . I think it takes 3 cups to make a loaf of bread. Not sure

Do you have to add more water?

Hell won't be big enough to hold all of the engineers.

Thanks Hank hill.

My dad had one on the farm when i was a kid ..wish i knew what happened to it...made me a nostalgic..

50 years ago as kids we had one of those and would drive around and spray people who were walking, 😂😂

Alright... i thought that was the cover of the valve. Thats a big ass doohickey....

a-1 video !! good explanation, what's' the part # for the bigger bearing ? can't find it, also can you remove front section to get to big bearing ,with out dropping steering column ?

Amazing the technique that you use to sharpen the unit bit, can you please provide me the type of bit you used on the dremel tool.

I have that problem.

Thanks I definitely needed this!❤

Cant find this code scanner anywhere. And lose that music, its very distracting..

How to get the sewer off on the ignition switch off?

Thank you so much

By the time I drank a 1/5th I got tired of the bs and looked it up lmfao

Please comment and give a thumbs up and subscribe if you like this. Thanks.

Michoacan

Yes i would believe how much work it is.I'm on my 2nd OBS Ford F150, this one has been horribly abused too. It is a lot of work, but also a lot of learn as you go.

Made in mexico and Canada see The padern that is the best people in The us won't work hard any more.

Waiting on the next episode! Great to see actual footage that’s not the tourist spots

It is nice to see videos with everyday views of a country like Mexico without the party life or resort type videos.

John Doe how to, You're the best! I just had to subscribe!

WTF DOES IT SAY ON THE HANDLE?!?🤪

I use my step drills reliably up to 3/8 in 0.125-0.140 annealed tool steel. You’ll probably, using a drill press, need to change your speed while going larger

Well that sucks because I ordered the same one a couple years ago and I'm just now realizing that it actually had all the extra parts with it. Only thing? Yes. Got was? A. Generator I had to provide my own oil. Didn't. Get? No wheels no handles. No nothing to late now I guess. That really sucks😅 my luck it could rain 100 dollar bills and I walk out and get pelted with penny's.

WHIRLPOOL WHY oh WHY

Manufactueres make working on cars intentionally harder. As a mechanic it really pisses me off.

The key must be in the RUN Position in order to push the locking pin up so you can remove the Key Cylinder out. It's all explained in the Haynes Repair Manual. What's most important that the actuating rod and the Ignition Switch are in the proper location. It's also explained in the Manual... Good video Sir ..😊

Had this issue with mine and was able to fix it by cleaning both sides of the circuit board with 90% alcohol. Mine had water that got into the housing over time

Hey I have 01 sub outback can find starter relay. Please help 😢

Thanks

RIP i just found out that my shaver was turned on after fully charged yesterday and it cant be turned off...same after depleting battery and let it dry. Any solution for that?

Great video! Re-assembling my 1995 F150 was driving me nuts, this video made it simple. Thanks!

Even if you fix their crappy circuit, the motor will burn out because they undersized it and didn't use a big enough gear ratio, so it's over loaded. I'm thinking about modifying one to take a proper motor, gear ratio, and maybe 18650. We shouldn't have to, though. This isn't a complex product to engineer. It should just work basically indefinitely.

Mine works well I just bought a mockmil for the kitchen aid it's a stone mill.

5 volts is all you need for this. I used 4 AA NiMH batteries in series. I did this on a 1993 Econoline and it got my brakes working well. The wiring on the RABS module is different in Econolines. All the RABS wires have two colored insulation. I connected (-) to the black/white wire, it being the ground for both solenoids. I alternated between applying (+) to the yellow/light green wire (dump solenoid) and the pink/light green wire (isolation solenoid). These being solenoids, polarity can be reversed. During the standard brake bleed, I smacked the calipers and drum brakes with a plastic mallet to free up any air bubbles stuck to the walls. I couldn't find an extra RABs connector, so I cut off my connector, wired it to my extension cord, did the RABS bleed, then soldered the plug back to the RABS. In hignsight, I should have also soldered some connectors in parallel so I can do this bleed again without cutting and mending wires again. I highly recommend getting a copy of your vehicle's electrical troubleshooting manual. That's what I used and so did John Doe How To. Thanks John!

🎉 I'm not subscribing to anything man all I need is one time use. Just need to know how to put the car and retainer back in my 9796 Ford F-150

Mines just done the same, seems to be a common problem. Shame as it was a great shaver. I wish the customer service was better. Thanks for the video, very helpful.

Mine just started doing it tonight.

Cannot understand your convoluted explanation

Hi, that transistor is labelled AQH, although, under the camera, it looks like A0H. It might be a PNP or NPN transistor from Chinese manufacturer Galaxy Microelectronics. They have very similar marking for several of their SOT23. They have lots of them but no search by marking feature. My pitbull is working fine but, since yesterday, without display. Cheers

Thanks John I thought the same thing . ridiculous

Thank you, learned something new and saved me a trip. All the while picturing Billy Bob Thorton. Apologies if I’m the first to say that.