So helpful. Done in about 15. Cheers

Hi there. South African here. And my Toyota hatch back looks similar to what have on here . Will give it a go and see how it goes.

for horn pad top, on wire spring ,push in and up, bottom, push in an down, for yellow cable junction, noe need to cut ties its simply on the right side just pull it out

Awesome video. Thanks!

The rear regulators don't have a cable to cut if it's stuck in the up position. Any tips on how to get the window down on a rear door?

You just saved me $350 bossman, appreciate you!

Why do they have to make it so fucking hard to do the simplest repair

Don’t relay on forklift hydraulics under load sht happens to new equipment let alone that beast

You didn't actually show the button being replaced. You showed how to take the door lining off and how to put it back on.

Beautiful.

How can you say if it's the motor or the gear? I have the same problem, but if I lift the glass with my hands and simultaneously push the window switch, it goes up, till a certain point, where it will again need the help of me lifting. Thank you.

Thank you so very much for this video. My local dealer quoted me $250USD for the labor alone. I bought the handle for about $10 online and installed it myself in about 10 minutes thanks to your video. I didn't have to unhook the electrical connectors as there was enough slack in the wires. I rested the bottom of the door panel on the speaker and unscrewed the old broken handle. Really easy to do alone, or easier with a little help.

18:26 nope that's not it man... you def destroyed the plastic bracket

14:39 you have to align the arrow with the little dot on the back site of the pump acutally. there is a tool for it also, torque spec 100Nm if anyone needs it and found this comment

whos done a 5.0 one? Cant get it out??

Love the sandals man; great vid very helpful thank you

Thank you on showing how to remove door handel.

Him laughing at the fact all that coolant draining out LMAO

Once again- thanks for doing these types of videos . They take the ‘ guess work ‘ out of the job👌

Not a PjPk Ranger .... Vid is PX--on If you clean the MAP every 20,000km all is ok

Cannot golet the front clip off ti save the life of me

Good tutorial bud.well done.nice and straight forward way you described every part of the job.thank you mate!!! I'll be back...lucas

Advice anyone, before i undertake this job. Intermittant alarm (no rhyme or reason to it). Dashboard shows passenger door open (locking sound when electonrically locking car doesnt sound correct alot of the time) Is this likely to just be a corroded passenger side door actuator?

Excellent video! We are not very handy and were dreading this fix, but it went super smooth thanks to you 😊

I got a ridiculously high quote to get mine fixed . Found this video on youtube, ordered the part from your website. Just replaced it myself in about 20 mins. It was very easy. Thankyou for the video!

I’ve bought two replacements and the button for driver window doesn’t work, the one with Auto on it. This button still works on the original switch unit but but doesn’t work at all on the two I bought. On the two I bought, all of the other buttons work fine.

Where is the 2003 Pajero evaporation file please?

I just need that little magnet thing i don’t want the screw to fall

98 hilux diesel 4wd engine compartment much tighter looking and different AND the 100amp fuse is shot - how does this change the alternator replacement plan if any?

Thanks man couldn’t of explained it any easier

Thanks. You're a legend.

Those bolts are not 12mm, they are 8mm with heads that fit a 12mm socket.

Those bolts are not 12mm, they are 8mm with heads that fit a 12mm socket.

Can you show me how to flash it on the Hyundai Metz

Duuuuuude, thank you sooooo much! I would never have worked that out. 🎉

Thanks for the video. When you compare both models, behind, it seems one connector is male and the other female. Are they the same?

Kill the music

Greetings from UK great tutorial very clear instructions 👍

got to the bolt where you said was rusty, yea thats as far as i got🤦🏽‍♂️😂

Thanks for sharing help me out👍

Hiya, after following all the steps I just couldn’t get the external handle of our i800 off. Is it slightly different? Another bolt or did I just need some more force? TIA

Дякую за відео.все просто і зрозуміло

Very helpfull THX

You must reconnect the door key tumbler rod for driver-side doors.

Good job man 👍

This video solved my problem. But Toyota charged me NZ$381 fir the switch. So, I got extra 3rd party part for emergency, which is less than NZ$80.

And to anyone ordering, with these guys I can guarantee quality product as I place my order at 1:20PM I was e-mailed same day with a tracking number.

👍👍👍👍

a mechanic quote me 700dollar for a genuine parts and the installation. crickey!

Thanks for that, came in handy when changing mine.