Пікірлер
@crazyrussiankid2865 14 сағат бұрын
Thanks man this was helpful
@braddomangue185 Күн бұрын
Awesome to the point video. Thanks bro!!!
@crankitt825 Күн бұрын
Glad it was helpful! Don’t forget to like and subscribe!!
@randal580 Күн бұрын
We’re can i order a transmission rebuild kit for a 2018 ranger 500
@crankitt825 Күн бұрын
Thanks for watching. Your best bet for transmission parts will probably be the Polaris dealer. I will be afraid of using aftermarket parts for that. It’s to much work to go back and do it again. Hope that helps you out.
@DEADPOLES Күн бұрын
Stator assembly needed
@crankitt825 Күн бұрын
Thanks for watching. I will be sure to Make one next time I get one in the shop.
@DEADPOLES Күн бұрын
All good I do the same thing a ktech from tx been swamped lately was trying to remember if you had to pull swing arm.. remembered in your video 👍
@gobraphil Күн бұрын
Great video! You just get to the details. Is this the same process for an xp900?
@crankitt825 Күн бұрын
Thanks for watching. We try to make them as simple as possible. I can’t say by memory if they are identical but the should be very similar.
@gobraphil Күн бұрын
They appear to be very different lol. I’m having to pull off the intake. Still awesome video!
@crankitt825 Күн бұрын
they are different. I’m not for sure if I have a video on the 900 transmission. If you can’t find one try looking up the transmission on the 1000s models. They should be similar. Hope that helps you out.
@laramiechesnutt8665 2 күн бұрын
Great video! Very detailed. Thanks!
@crankitt825 2 күн бұрын
Glad it was helpful! Be sure to like and subscribe to our channel.
@laramiechesnutt8665 2 күн бұрын
This was great! Thanks!
@crankitt825 2 күн бұрын
Glad you enjoyed it! Be sure to like and subscribe to our channel.
@drmarkintexas-400 2 күн бұрын
🏆🛠️⭐😎 Thank you for sharing this
@crankitt825 2 күн бұрын
No problem 👍 glad you enjoyed it. Be sure to like and subscribe to our channel.
@drmarkintexas-400 2 күн бұрын
🏆🛠️⭐😎 Thank you for sharing this
@crankitt825 2 күн бұрын
Your very welcome. Don’t forget to like and subscribe to our channel.
@christianarsenault6544 2 күн бұрын
Sweet videos
@crankitt825 2 күн бұрын
Thanks!
@BrianMason3636 2 күн бұрын
I’m,a try this tomorrow thank you for sharing my friend!
@crankitt825 2 күн бұрын
You’re very welcome!! Be sure to like and subscribe to our channel.
@rondawson583 2 күн бұрын
Thanks for the vid. This is something I will not attempt, enjoyed watching though.
@crankitt825 2 күн бұрын
Thanks for watching be sure to like and subscribe to our channel.
@CharlieKeelan 3 күн бұрын
Thank you for your posts. We have a honda rancher like this one that is shifting gears on its own. When it goes to the 4th gear it will kick into 5. Is this a clutch problem? Thank you for your help.
@crankitt825 2 күн бұрын
Is the machine throwing any codes? If not I would definitely check my clutch and shifting forks. Hope this helps you out and thanks for watching. Be sure to like and subscribe!!
@danielrowe2962 8 күн бұрын
If Honda recon doesn’t move while in gear would both clutches prevent it from moving?
@crankitt825 8 күн бұрын
If either clutch goes out it will prevent the atv from pulling however 90 percent of the time it’s always the pads on the clutch basket. While you have the primary clutch off check the pads on it also. If the pad is worn and you can see metal then I would replace that one also. Thanks for watching and be sure to like and subscribe.
@jamesandrews1130 9 күн бұрын
I was curious about flost bowl too. And they day not to read the comments.😊
@crankitt825 9 күн бұрын
Sorry I don’t understand. Thanks for watching!!
@leannstark543 10 күн бұрын
I replaced my battery, before it would not turn over at all. Now it tries to crank but won’t. (And yes, it has gas 🫢)
@crankitt825 10 күн бұрын
Thanks for watching. Sounds like the carb needs to be cleaned or possibly rebuilt. Hope that helps you out.
@trev9177 11 күн бұрын
i know this video is a year old but i got a rzr 1000 xp pro throwing two codes according to the little info i have researched it has to do with the throttle side but i still am having a hard time troubleshooting some help would be greatly appreciated
@Paigecowan1031 11 күн бұрын
How do you reset the screen?
@crankitt825 11 күн бұрын
Thanks for watching. Once you fix the issue the screen will reset itself.
@Jerold-bu3ul 13 күн бұрын
Cant believe a polaris wheel bearing would go bad.
@crankitt825 13 күн бұрын
lol, all the time if you don’t keep them grease. Thanks for watching. Be sure to subscribe.
@TheRichard4098 14 күн бұрын
I have a question that maybe you can help me with, I thought it was my neutral switch that was bad, because when I put it in neutral the light would not come on and it would not start. so i replaced it, but still did the same thing, so then I checked relay for it and put a new one on and still does the same thing, it is getting fire to switch from the wire, and the bulb is fine and that also gets fire. then I noticed if I hold down the foot shifter I can hear it get contact with something and then neutral light comes on and it will start.. but if you let shifter go then it comes back up a little on its on and does not make contact then with what ever it is making contact with and then again no neutral light and no start... Do you no what I can do to fix this , even though this video is for a 350 mine looks the same its a 1997 yahama kodiak 400 4x4
@TheRichard4098 14 күн бұрын
I have a question that maybe you can help me with, I thought it was my neutral switch that was bad, because when I put it in neutral the light would not come on and it would not start. so i replaced it, but still did the same thing, so then I checked relay for it and put a new one on and still does the same thing, it is getting fire to switch from the wire, and the bulb is fine and that also gets fire. then I noticed if I hold down the foot shifter I can hear it get contact with something and then neutral light comes on and it will start.. but if you let shifter go then it comes back up a little on its on and does not make contact then with what ever it is making contact with and then again no neutral light and no start... Do you no what I can do to fix this , even though this video is for a 350 mine looks the same its a 1997 yahama kodiak 400 4x4
@crankitt825 13 күн бұрын
Hi and thanks for watching. Take the wire off your neutral switch and ground it to the battery. If everything goes to working then I would say the switch is faulty or what trigger the switch in the side cover isn’t lining up. Hope this helps.
@TheRichard4098 13 күн бұрын
@@crankitt825 ok i will try that when I get outside in a few, I did put a new neutral switch on it that I purchased, and it did the same thing as the old one. I learned that if i keep my foot on the shifter bottom left on engine then the neutral light comes on, but if i take foot off and the shifter arm goes up a little on its on then the neutral light goes off and will not start again, I can hear something make contact at the bottom around the shifter when I hold it down, but I have no clue what it is making contact with the rod that the shifter bolts to does not seem to have nothing around it as it goes into engine.... and been unable to find anything online that has to do with this issue at all.
@crankitt825 13 күн бұрын
could be a bent shifting fork on the clutch side (right side). If my first suggestion doesn’t work then I would check on that. On stuff like this that doesn’t usually happen it’s just a search and look until you come across it. Hope this helps.
@TheRichard4098 13 күн бұрын
@@crankitt825 I tried the ground to wire but was no light showing up for neutral. I bet its just not getting contact somehow on the inside, cause sitting I can change gears then go back to neutral and no light then i take my foot and lift up barely on the foot shifter and the light comes on. I bet it would be a nightmare to fix if i have to take it apart to fix that problem.
@crankitt825 13 күн бұрын
the light should have came on when you ground the neutral safety switch wire to ground on the battery. If it didn’t I would suggest you check all your grounds coming off your wiring harness. Make sure they are all clean and getting a good connection and try grounding the neutral safety switch wire again.
@crabzyagent272 14 күн бұрын
what does it mean the symbol when its blinking
@crankitt825 14 күн бұрын
A flashing wrench symbol alerts the operator that the preset service interval has been reached. Thanks for watching be sure to like and subscribe!!
@ambrycerbr 15 күн бұрын
Thank you for taking the time to make this video? Now, I feel confident enough to do this on my machine which should save me a bunch of money.
@crankitt825 15 күн бұрын
Your welcome, glad we could help. Be sure to like and subscribe.
@andrewdaniels9698 15 күн бұрын
Excellent video, just what I needed to see. I also took your recommended links. Thanks very much.
@crankitt825 15 күн бұрын
Glad we could help you out. Thanks for watching and be sure to like and subscribe to our channel.
@andrewdaniels9698 15 күн бұрын
@@crankitt825 I have. The least I could do.
@TheJNALife747 16 күн бұрын
will a bad voltage regulator not allow the battery to charge?
@crankitt825 16 күн бұрын
Yes a bad voltage regulator will not charge the battery. Thanks for watching!!
@TheJNALife747 16 күн бұрын
@@crankitt825 thanks 😊
@TheJNALife747 19 күн бұрын
I have a 600 mule and it will not start unless I jump it with another battery? Any ideas? Will this theory help me?
@TheJNALife747 19 күн бұрын
Also it’s a brand new battery
@crankitt825 19 күн бұрын
Yes, if you know the battery is good try this method. If it pass this method then I would probably have my starter tested. Thanks for watching. Be sure to like and subscribe.
@TheJNALife747 18 күн бұрын
@crankitt825 awesome thanks for all your help
@crankitt825 18 күн бұрын
your welcome
@TheShockLoad 20 күн бұрын
Great video. I dont have the patience to make videos like this. One life hack. Heated the bearings slightly with a torch and they hand fit onto shafts, also heated the alum case around bearing seating areas and case went on by hand also. It dont take much heat!
@crankitt825 20 күн бұрын
Thanks for the tip and for watching my videos.
@LipsandLashesMusic5689 20 күн бұрын
Wish this would’ve been in focus
@crankitt825 20 күн бұрын
Sorry for the glare!! Thanks for watching.
@floydroebuck7782 22 күн бұрын
How about a very slow Idle speed? Same thing most of the time?
@crankitt825 21 күн бұрын
Is it throwing any errors codes? If not clean throttle body and try resetting your IAC sensor.
@WilliamCarnes-v9y 22 күн бұрын
Thanks for the video!!!
@crankitt825 22 күн бұрын
You’re welcome and thanks for watching!!
@StarknightMT_official 25 күн бұрын
Hello, Are you interested in testing our products? We would like to invite you to test the Camo Seat Cover for your 2023 Polaris Ranger XP 1000,
@crankitt825 24 күн бұрын
Thanks for watching. We are a mechanic shop that works on ATV and UTV. We don’t own a Ranger 1000.
@StarknightMT_official 22 күн бұрын
@@crankitt825 Hi, thanks for letting me kow. Have a good day!
@bengreen7383 25 күн бұрын
Hey, I thought that was the cdi box???
@dorianfulton7168 25 күн бұрын
Great content, thanks for the really crisp editing.
@westleywoods497 25 күн бұрын
What does it mean if you screw that in and transmission still doesn’t pull?
@crankitt825 25 күн бұрын
Sounds like transmission problems. It should manually put it in second gear when that is screwed all the way in.
@SteveVia-e4i 26 күн бұрын
Man I really appreciate the brevity of your videos. You are able to save your viewers a lot of time they would rather not spend listening to music or watching brand/ego boosting videos. Thank you bro.
@grant9509 28 күн бұрын
I have a 2007 or 2008 Ranger 700, right now it’s idling fine, sometimes requires a little throttle to get it to crank. But once it’s running, when I try to engage the throttle, it bogs down to where it almost dies out. I pulled the spark plugs and found they had a significant amount of carbon on them and I’m replacing them. I checked the fuel pump and it works fine. Does anyone have suggestions for this issue?
@crankitt825 27 күн бұрын
Is it throwing any codes? How much fuel pressure does the fuel pump have?
@grant9509 27 күн бұрын
@@crankitt825 after I turn the key on 3 times, it says “wait” then doesn’t show a code
@crankitt825 27 күн бұрын
no codes, that’s good. All sensors are working correctly. How much fuel pressure does your fuel pump have?
@grant9509 27 күн бұрын
@@crankitt825 well I figured it out. Apparently one of my kids put the parking brake on. As soon as I released it, the engine ran fine! Thank you for the advise though!
@crankitt825 27 күн бұрын
great glad you got it figured out. Be sure to come back and watch our other videos. Be sure to like and subscribe to our channel.
@hankhurless5446 29 күн бұрын
Took my muffler off and knocked the honey comb out (that’s what I call it anyway 😂) put it back on and threw this code 3056.
@crankitt825 29 күн бұрын
Thanks for watching!! Check your 02 sensor. Hope this helps.
@stephenjordan2689 Ай бұрын
I have a big bear I just put a new carb on it runs fine idling but when i put it in gear and give it gas it Boggs down, also I have 3 lines on carb fuel, overflow but what is the other line, your help would be appreciated
@crankitt825 Ай бұрын
Hi and thanks for watching. The 3rd line is a vent line. Make sure your jets in the carb are install correctly. If so then it sounds like to me your loosing vacuum. Replace the top and side diaphragm. Hope this helps. Be sure to like and subscribe.
@CB-lg8qf Ай бұрын
Can anyone tell me where the small breather line comes from that goes into the air filter box? The one that is located on the passenger side. I know where the other one comes from but don’t see it on my recently bought atv. It had its air box removed and I don’t see any line that goes to that passenger side.
@crankitt825 29 күн бұрын
What size and model Ranger do you have?
@obspowerstroke1864 Ай бұрын
What is the proper way to get all the air out of the coolant system on these 800s I’ve been having issues with getting all the air out of my system and I’ve bled it on the bleeder valve on the head and raised the front end up to put the air to the radiator and none of it is getting all the air out
@crankitt825 Ай бұрын
Hi and thanks for watching. That is the proper way on burping the coolant. If you’re still getting air, I would go to the part store and get me a coolant pressure test. This will let you know if you have a bad radiator, any loose water connection, or a bad head gasket. Hope this helps you out.
@thomascollins3200 Ай бұрын
Thank you for sharing
@crankitt825 Ай бұрын
Your very welcome!! Thanks for watching.
@Jackie_44 Ай бұрын
Hey if possible how do I change the clutch on one of these
@crankitt825 Ай бұрын
If you’re experiencing slippage try adjusting the clutch. That will fix it in most cases. Thanks for watching.
@brianhammond81 Ай бұрын
How can you delete the code without a scanner
@crankitt825 Ай бұрын
Hi and thanks for watching. Once you fixed the issue the codes will clear themself.
@brianhammond81 Ай бұрын
@@crankitt825 oh ok thanks
@crankitt825 Ай бұрын
your welcome
@crankitt825 Ай бұрын
I would test the stator and if it passes then I would change the rectifier (voltage regulator). Power from the stator goes to rectifier and turns the power from ac to dc voltage. A bad rectifier might be causing the short. Hope this helps. Thanks for watching and be sure to like and subscribe.
@TBD0621 Ай бұрын
What would cause the black wire on the stator to smoke hot while using the starter button on the handle bar? stator grounded out?
@Baconfat11 Ай бұрын
Glad I saw this video. I was about to start on wiring. You fixed my problem in 30 seconds
@crankitt825 Ай бұрын
So glad we could help!! Be sure to like and subscribe!!
@danielanaya7813 Ай бұрын
How do you pull the flywheel
@crankitt825 Ай бұрын
Thanks for watching. I hope the video helped you out. For one on one online help consider joining our membership. It’s a great way to get information on how to diagnose and fix your machine. ( once you remove the nut off the flywheel you will need a flywheel puller for that machine to remove the flywheel)
@legorgio Ай бұрын
How do you change it from kilometers to miles plase?
@mighty_Buttercup Ай бұрын
Would you have any suggestions on what to troubleshoot on a Polaris Ranger 800. It was just randomly shutting off, the battery tested as bad so replaced the battery and now it wouldn't start at all. Tested the new battery and it is fine and is installed correctly. There are no lights, no clicking when you turn the key, just completely dead. Thank you
@crankitt825 Ай бұрын
Thanks for watching. To start with I would check to see if I had power going to my key switch and coming out when I have it in the on position. If you don’t then the key switch is bad. Hope that helps.
@mighty_Buttercup Ай бұрын
@@crankitt825 Thank you. It's my mom's Ranger and my dad knew how to fix anything under the sun but he recently passed away and KZfaq has become my only tool to try and help her out because I'm totally clueless but can follow directions lol I appreciate the suggestion, I will try it out next time I go out there. 🤞
@crankitt825 Ай бұрын
your welcome, be sure to like and subscribe to our channel.
@jungleify Ай бұрын
thanks good vid! I'm thinking of putting a snowplow on my 2x4 Ozark 250. You think it will perform well plowing snow with some sandbags on the rear?
@crankitt825 Ай бұрын
Thanks for watching. Glad we could help you out. These are great quads but I wouldn’t think it will be big enough to push snow.