Hey, can you give me DMX 512 to the SPI decoder which can work with this LED group (WS2815), I try to create a DIY pixels mapping but it's always difficult for it to work. Thank you for this video she helped me
@LEDStripStudio22 күн бұрын
Our small SPI LED controller can convert DMX512 to any SPI signal (including WS2815): www.ledstripstudio.com/spi-led-controller/
@raphaelakpan298027 күн бұрын
How can I be part of this, I am in Nigeria
@LEDStripStudio26 күн бұрын
Hi, you have to come to visit us in Bratislava/Slovakia on 21-22 August
@tsindaalpha7583Ай бұрын
H.U.G.E
@TheOpusChristiАй бұрын
Magical
@michaelatongmfomor8008Ай бұрын
Please can anyone help me figure out this! Please 🙏🏻🙏🏻🙏🏻🙏🏻
@michaelatongmfomor8008Ай бұрын
Hi thanks for this video I follow exactly your steps but my pixel bar light still not receiving data
@LEDStripStudioАй бұрын
hey, hard to tell. the tutorial is for pixel strips/or SPI pixels in general, when you are using some king of Art-net to SPI decoder ( like SPI Matrix ) so it can be thousand different reasons ( perhaps only few, but you get the idea ) but I strongly suggest to check resolume forums - resolume.com/forum/
@DK-vx5co2 ай бұрын
Can one power a strip from only the middle? I have not found an answer to this.
@LEDStripStudio2 ай бұрын
you definitely can. keep in mind the voltage drop. it can even have some benefits, though from our experience its usually bit harder to do it compared to when you power the strip from the start.
@DK-vx5co2 ай бұрын
@@LEDStripStudio Thanks. What is harder? Soldering? I think I have the soldering down pretty well. Do you have any videos on this? I may have missed them.
@LEDStripStudio2 ай бұрын
@@DK-vx5co to access the point in the middle of the strip compared to the start. and yes, soldering in such point, when the strip is already in the profile, is challenging - kzfaq.info/get/bejne/ftugaaR7l8XYgKc.html - maybe this one, for beginners.
@tsindaalpha75832 ай бұрын
This is absolutely amazing !! Well done ,i subscribed to see more
@firestarter99453 ай бұрын
thanks for the video. i have a question though. can i solder / bridge the GND with backup signal DIRECTLY on the LED strip? (WS2815) And then connect it with just one wire to the controller?
@LEDStripStudio3 ай бұрын
kzfaq.info/get/bejne/b5mVd72qmZ7MiWg.html - yes you can! with this specific IC that is what we are actually doing
@firestarter99453 ай бұрын
@@LEDStripStudio Thanks! :)
@ArshadKhan-cr2yk3 ай бұрын
Hi I need your help
@djdjdjersan4 ай бұрын
Please tell me some spi DMX controll but has sound active mode that i can trigger different sound mods, and can trigger pre created scenarios. Something like govee or twinkly light controller. Some simple spi but not with Bluetooth and smartphone, with DMX i need.
@LEDStripStudio3 ай бұрын
hi! pre/created shows you can create in our software and then play from the PC. check out our SPI Matrix :)
@djdjdjersan3 ай бұрын
@@LEDStripStudio So as i understand you don't have product as i describe. İ don't want to get in artnet or alternatives, and as I'm, there is many people don't want to get in that addressing. I don't know how hard to make that kind controller but it will clean for many people many problems with led strip in clubs bars, disco's or Mobil DJ systems. Many people will get it cuz it's 1000 time easy for some line strip users. Most places are not really screen style led friendly and for 40 meter line strip really don't want to get in ic led adressing or any extra program.... But anyway thank you very much for answer....
@erroos4 ай бұрын
What’s app name?
@shawnk78634 ай бұрын
"Promosm"
@LEDStripStudio4 ай бұрын
DMX as trigger while using DMX Synchronization is now an AVAILABLE! We have added this functionality so that you can now use DMX as your trigger for the animations.
@dhirajmaru15644 ай бұрын
Can you guide which app is used or how to use for coding led suits
@LEDStripStudio4 ай бұрын
LED Strip Studio Software :) check out our page and download the free demo if you want!
@victorwestmann5 ай бұрын
What about connecting a LED strip to an Athom controller?
@LEDStripStudio5 ай бұрын
Hi, there are many controllers in the world and we can test all of them unfortunately. Anyway, if it can generate DMX, Art-Net or http commands, you should be able to use all our LED strip controllers (thus LED strips) using Athom.
@Gofernpower6 ай бұрын
What is the power supply method of this LED?
@LEDStripStudio5 ай бұрын
you can either power the strip directly from the Reactivo, or you only lead data line plus ground and power separately strip and the device. voltage range is 5-24V
@djdjdjersan6 ай бұрын
Hi!! I dont know how i can describe but i need something like, goove controller or spi music controller that i can control with dmx in order to control dimm - blackout - single color control rgb - strobe - but most important able to be calling preprograms as chases and soundactive modes. like this small china led controllers but dmx controlled. Im using Soundswitch as dmx program. or do you have any advice? or can you advice some platform i can find more information or can ask questions about that led stuff ?
@LEDStripStudio5 ай бұрын
hi, thx for the question. we currently don't have live sound to effect feature in either software or in hardware. a workaround is grabbing the content from your monitor / kzfaq.info/get/bejne/e7qYZs2rtZjYdXk.html Another option is to create Music synced show, though this is for a specific song. You can then use DMX to recall the effect from the software which will also play your sound. Pure standalone solution would involve 3rd party device, such as ImageCue - it can play sound and trigger your effects at the same time from your controller.
@rajeshprasad61767 ай бұрын
Nice🎉
@grupasc7 ай бұрын
Czyli takie podłączenie spowoduje ze kopia zapasowa będzie działać bez problemu tak ?
@LEDStripStudio5 ай бұрын
Tak :) though it is worth noting that this is for the strip type that we are using.
@PraveenSharma-be1du7 ай бұрын
Can we export animation bin file to transfer on an IC
@Sg_movies.homies8 ай бұрын
Hey I am new to this stuff Can you give me a rough layout to What to learn ? Step by step
@LEDStripStudio7 ай бұрын
hey. what it is that you want to achieve? Reactivo is a nice little controller that you can have lots of fun with. Pretty powerful for that size and price tag. And I can ONLY recommend this page for starters - https:\ eactivo.lighting
@OffTheHorizon8 ай бұрын
How many led strips can you connect the reactivo pixel controller?
@LEDStripStudio8 ай бұрын
as many as 1024 pixels, e.g. 17m of strip that has 60 diodes/meter. or 6 Art-net universes
@JesseDalba8 ай бұрын
Will it play doom?
@LEDStripStudio8 ай бұрын
Now that is a good question :D will try
@EnderHeroics8 ай бұрын
do you have to buy the 225$ remote for this to work
@LEDStripStudio8 ай бұрын
Yes, you need a controller, which converts the screen data and powers the strips.
@cucciolo1828 ай бұрын
wow thats sick
@user-pl6ch8il3c9 ай бұрын
I get that you guys understand what is happening, but it's hard for others to understand what's happening here. there is no real structure to the way you are presenting the information. You guys seem to have the information I am looking to lear, but I feel like I wanted into the middle of a conversation you guys were already having.
@LEDStripStudio9 ай бұрын
Got it! Thx for feedback. Which topic are looking to learn more about?
@user-pl6ch8il3c9 ай бұрын
@@LEDStripStudio , No worries at all. Thanks for being open to the feedback. You guys have great information to share!
@malachiorgad96899 ай бұрын
This is ws2812 ?
@LEDStripStudio9 ай бұрын
Basically,yes.
@LeroyvanAerleDCH5 ай бұрын
Where can I found the led panels? We now got big dots on our ceiling (8 years old)
@beatboxxdannyschwarzboxing97689 ай бұрын
Could you explain why your outputs start at universes 1, 7, 13, and 19 whereas I have the same device and in the configiration the universes for each output start at 1, 8, 15, 22?
@LEDStripStudio9 ай бұрын
Sure, the 1, 8, 15 and 22 are not fixed universes. You can set the device (SPI Matrix) to e.g. use just universe 1 for output 1, use universe 2+3 for output 2 and so on. And as it is set in the device, we have to use it in the mapping. By default, the outputs are set to use 1-7, 8-14, 15-21 and 22-28 for output 1, 2, 3 and 4.
@erberon8210 ай бұрын
finally 🙏.Im using exactly this setup and was struggling about the connection.
@ishowuart1711 ай бұрын
i use H802RA with resolume & ws2811...it only can hanlde 170 pixel or 8.5meter led strip. So how to use 30 meter in one port h802RA
@LEDStripStudio11 ай бұрын
I'm sorry, we don't use H802RA, so you must ask the producer of the device.
@theclayj11 ай бұрын
LETS GOOOOO
@ditomaggio111 ай бұрын
This was the most anticipated feature thanks guys you are doing a great job !
@LEDStripStudio11 ай бұрын
Thank you, we try :) ...
@user-he3xk9in5r11 ай бұрын
Do you guys supply to Nigeria?
@LEDStripStudio11 ай бұрын
Hi, yes, we ship worldwide. You can check our eshop here: ledstripstudio.com/shop/
@user-he3xk9in5r11 ай бұрын
Pls I need to learn more.
@manukalias Жыл бұрын
Very nice installation and effects, Love from India 🇮🇳🇮🇳🙏🙏
@joshuapenrose Жыл бұрын
This is great work -- I love it! What is the fabric you used to diffuse the light? Thanks!
@LEDStripStudio Жыл бұрын
Thank you, we're happy to hear you like our job. We use projection canvas as diffusor.
@manukalias Жыл бұрын
Superb 😍😍
@shackled1502 Жыл бұрын
sorry im kinda late to the video but, can someone explain why injecting power at the end doesn’t break the cables? because if you plug it in the wrong polarity it’s going to break right?
@LEDStripStudio Жыл бұрын
if you would change + and GND then yes, you would probably fry some pixels. so it is important to follow the correct pinout.
@adamarabas1445 Жыл бұрын
Znám vás hodinu a myslim si, že jsem váš NEJVĚTŠÍ fanoušek😊
@LEDStripStudio Жыл бұрын
To sme radi 😁😁👍👍
@akilight Жыл бұрын
Do it require any key? Or with the use of Artnet it can work?
@LEDStripStudio Жыл бұрын
Of course you need some license for Madrix.
@brandonashburner7967 Жыл бұрын
What type of lightbulb have you used here?
@LEDStripStudio Жыл бұрын
ledstripstudio.com/shop/product/edison-cct-white-light-bulb/ Let me know if you need more information on [email protected]
@roro.py2 Жыл бұрын
How to apply this animation
@LEDStripStudio Жыл бұрын
Hi, apply where?
@ProjectileObjects Жыл бұрын
But there are also addressable LED DMX512IC strips?
@LEDStripStudio Жыл бұрын
Yes, there are. But we are not fans of those as well. It's just too many cables for pixel LED installations. More details here: ledstripstudio.com/why-is-it-even-more-stupid-controlling-digital-led-pixels-using-dmx/
@ProjectileObjects Жыл бұрын
@@LEDStripStudio @LED Strip Studio I read that article and in no way does it cover 5 pin digital DMX512 LED strips. The DMX512ICs receive DMX data communications directly. You can wire a 3 pin DMX or RJ45 cable directly to the strip. Additionally, they run in parallel, not Serial (SPI) and any number of LEDs or ICs can die on the strip without stopping the flow of data. SPI has a single break point, and dual break point for 4 pin PCBs with backup data line. I'm not a fan of DMX, but for professional long term installations SPI has some risks. Once again, this is 5 pin PCB DMX512IC chips I am talking about. Not DMX to SPI
@LEDStripStudio Жыл бұрын
170 LEDs limitation is really a problem, once you want to use e.g. 10000 LEDs in installation. That's our point of view. Of course you can find some benefits using DMX... either way, we just don't think it's practical.
@ProjectileObjects Жыл бұрын
@@LEDStripStudio I understand that point but most 24V are 6LEDs per pixel/IC, and most control boxes still use Artnet to DMX. The $200 box I typically use has 8 universes, so that's 1360 ( or 8160 LEDs / 136 Meters). And still to the point. If you are running 10000 LEDs from a single Artnet to SPI box and you have a break point 100 pixels in, then you'll have 9900 non-functional LEDs until you fix the break point. I wouldn't take that change running anything architectural where a lift or crane would be required to do the repair.
@LEDStripStudio Жыл бұрын
That's exactly why we use SPI Lamps for: ledstripstudio.com/spi-signal-splitter/
@jenabMaNI Жыл бұрын
Hello I have question , how to buy or take beautiful health and mana bar in dota2
@LEDStripStudio Жыл бұрын
Hello. U need a controller such as Reactivo, setup your Screen Grabber in the Reactivo software and you are good to go :)
@juliomartinnovoavela1095 Жыл бұрын
Por favor necesito el software
@LEDStripStudio Жыл бұрын
Hi, sure, please go to ledstripstudio.com/addressable-led-pixel-mapping-software/
@juliomartinnovoavela1095 Жыл бұрын
Amigo necesito un software para colornie dmx controller cuál me recomiendas por favor
@juliomartinnovoavela1095 Жыл бұрын
Yo soy de Perú y como me envías el software
@LEDStripStudio Жыл бұрын
@@juliomartinnovoavela1095 We don't use DMX controller. But if you mean SPI LED controller, you can check our LEC3 device: ledstripstudio.com/ethernet-spi-pixel-controller/
@LEDStripStudio Жыл бұрын
@@juliomartinnovoavela1095 Software can be purchased on our web, no need to send anything.
@andrejshevcov901 Жыл бұрын
🤣🤣😅the end is Brilliant!!
@LEDStripStudio Жыл бұрын
Yes, we like to have fun here 😁...
@dannywilson9336 Жыл бұрын
What software are you using?
@LEDStripStudio Жыл бұрын
This is our software - LED Strip Studio - ledstripstudio.com/download/lss3.zip
@guidoargel9414 Жыл бұрын
The software works with HD108 16-bit LED Strips to? Or only 8-bit leds?
@LEDStripStudio Жыл бұрын
According to the specification "The protocol of the HD108 LED strip is the same as the APA102 LED strip light." - thus it should work with our controllers. But the question is related more to controller than the software. If the controller supports HD108 and can receive Art-Net, you can use it with LED Strip Studio software.