1000mm/s: RELAXED TESTING on Voron Ferrari!

Рет қаралды 559,257

2 жыл бұрын

I started with a V0.0 Kit from Aliexpress (now it's 0.1, which is better in any respect)*:
Formbot Voron V0.1 Kit (AliExpress) bit.ly/39kfWdC
LDO Voron V0.1 KIT (Caribou3D) bit.ly/3KBxqzL
Recommended Kits for bigger DIY printers:
Voron 2.4 Kit (AliExpress) kit bit.ly/3PklmWE
Voron Trident Kit (AliExpress) bit.ly/3yxMaNe
STL files, instructions and BOM on the recent upgrades:
247printing.gumroad.com/l/247...
Support my work at Patreon:
/ 247printing
My Instagram and Twitter - more about my doings and behind the scenes:
Instagram: / 247printing
Twitter: / 247_printing
Watch the print at 1100mm/s:
• Shorts
💚Pizza, Beer and Coffee helps me going on💚
paypal.me/247printing
💚Thanks to all who support/ed my work💚
---------------Settings:
Filament: ESUN ABS+ - a great choice filament for strong parts and easy printing
amzn.to/3Bi0x7k
T_Hotend = 290C
T_Bed = 90C
Requested Speed: 1000mm/s
Acceleration: 35.000 mm/s²
square_corner_velocity: 15mm/s
Nozzle: 0.4mm
Layer Height: 0.1mm
Line width: 0.4mm
Volumetric flow: 40mm³/s
Lengths of straights: 65mm
Lengths of printing @ REAL 1000mm/s: 35mm
Xxxx ALL DESIGNS AVAILABLE SOON xxxX
@ Voron Users / Thingiverse
******UPGRADES STAGE 1 on my Voron V0 - VIDEO DEEP DIVES and ANALYSES incoming:
For years now, I use BigTreeTech/BIQU products - very much recommended:
(I was sponsored with an Octopus Board V1.1, TMC2209, 70W Heater and PT1000 thermistor)
Get the Octopus Board here:
bit.ly/31kKCrj
-MOTION (Part 1: Video Deep Dive incoming)
Nema14 spec Voron V0.1 @1.7A (OMC 14HS20-1504S)
amzn.to/3kBO5tm
F623 bearings instead of toothed idlers
amzn.to/2UktSgZ
WD40 specialist dry lubricant for rails (PTFE)
amzn.to/3ziGaF4
Gates-LL-2GT 6mm belts
amzn.to/3kCaAht
- EXTRUSION: (Part 2: Video Deep Dive)
Slice Engineering Mosquito Magnum (5% off!): www.sliceengineering.com?p=rkjO5IsbY
VolcoMosq Block (+9mm melt): • How did I end up with ...
E3D Hemera (Bowden config)
amzn.to/3zdvAzk
Capricorn Bowden Tube
amzn.to/3kBrgWE
50W heater (24V)
amzn.to/2UmOIwa
PT1000 temp sensor
amzn.to/3ivfdY2
Boron Nitride Paste @ heater, thermistor and heat break
amzn.to/3kvPem6
- COOLING (Part 3: Video Deep Dive)
4010 blower fans (24V), updated toolhead
amzn.to/3irazKT
optimized air ducts for part cooling with aluminium tape insulation
amzn.to/3zhbuEs
External Static Cooling: 4x4020 fans (24V)
amzn.to/3zcap0D
4x40mm heatsink at AB stepper motors
amzn.to/3irvLAh
2x 4020 / or 4010 fans (5V) at heat sinks (stepper motors)
amzn.to/3wOmfMJ
25mm axial fan (5V) for stepper drivers
amzn.to/3eDf4AW
- Software / Firmware / Controllers (Part 4: Video Deep Dive):
Klipper
www.klipper3d.org/
Raspberry Pi Zero W (Mainsail)
amzn.to/3xR9l21
Raspberry Pi 3B (Input Shaping and Octoprint)
amzn.to/2UwIMAu
Alternative: Raspberry Pi4:
amzn.to/3kBt4io
Simplify 3D: multi processes used
www.simplify3d.com/
-------------------------------------------------------
My modest video gear*:
iPhone 11 Pro: amzn.to/2VZYswJ
Smartphone video rig: amzn.to/3iriub5
GoPro Hero 9: amzn.to/2UZI9Q5
FLIR ONE PRO: amzn.to/2UWAe67
Similar to the soft boxes I use: amzn.to/3xRes2d
Similar to the tripod I use: amzn.to/2V1I6mw
*Amazon links are affiliate links at no extra costs for you!
#JoinTheSpeed
#247printing
#volcomosq
#SpeedBoatRace

Пікірлер: 627

@247printing 2 жыл бұрын

All details in the video description👍 Watch THE FULL PRINT of this here: kzfaq.info/get/bejne/l8uYdqqS0eCYnac.html

@brimful-cookie5947 2 жыл бұрын

what heater did you use for the mosquito magnum

@247printing 2 жыл бұрын

@@brimful-cookie5947 it’s a 50W heater cartridge here, but I am considering a more powerful one because of the external cooling

@brimful-cookie5947 2 жыл бұрын

@@247printing thanks.

@brimful-cookie5947 2 жыл бұрын

@@247printing i love your videos and im building a voron because of you.

@247printing 2 жыл бұрын

@@brimful-cookie5947 wow thank you - gives me honest goosebumps reading that! You won’t regret the choice - I had so much fun and so many learnings with the Voron!

@alphastratus6623 2 жыл бұрын

How to avoid warping: print the whole part before the bottom layer gets cold.

@247printing 2 жыл бұрын

Indeed! Speed helps against warping - don’t give a chance to internal stresses of the part 😬 - print at „warping speed“😂

@alphastratus6623 2 жыл бұрын

@@247printing I know, that's the whole point of the comment. It's funny because it's true.

@247printing 2 жыл бұрын

@@alphastratus6623 we agree! Thanks for commenting !

@DardanelleNews 2 жыл бұрын

How about "super glue." Works for me. Print on glass so you can scrape it off but glue your part down in about 4 to 6 places. It's worth it.

@247printing 2 жыл бұрын

@@DardanelleNews I stopped using adhesive stuff since I use structured or PEI coated spring steel on magnets. But for glas it’s perfect indeed! 3Dlac was my go to here - perfect adhesion, you don’t need much and you can remove it with water 👍

@xavierlara8389 2 жыл бұрын

This is a good illustration of how the client imagines the 3D printing process.

@247printing 2 жыл бұрын

Because it’s a so called „rapid“ prototyping process 😬

@DreainCZE 2 жыл бұрын

@@247printing its True tho even ať 25mm/s its still way faster than making a form

@247printing 2 жыл бұрын

@@DreainCZE absolutely! And for single rapid prototyping parts on design iterations it totally makes sense to have a fast printer

@alejandroalcocerzurita4668 2 жыл бұрын

That's true!!! Jajaja

@joachimtheboss5326 2 жыл бұрын

i expect this 5 kilo print in like half an hour

@SketchbookGuitar 2 жыл бұрын

Sir, you should't feed your printer meth.

@Neojhun 2 жыл бұрын

Straight up tweeking on the small coverage.

@vladimirpalaguta9445 2 жыл бұрын

you need an aerodynamic nozzle, the wind drives strongly and creates resistance)))

@Wingnut353 2 жыл бұрын

Just print in full vaccum...

@louiscrespo1280 2 жыл бұрын

@@Wingnut353 that would suck for materials that need to be in a heated chamber

@traviswatson6527 2 жыл бұрын

@@louiscrespo1280 I think opposite. Without air, no convection for heat loss from part. Flip side -- no cooling at all...

@L3X369 2 жыл бұрын

@@traviswatson6527 Water cooling

@dashlambda6707 2 жыл бұрын

@@L3X369 I wonder what materials would respond well to water sprayers for print cooling.

@Lucas_sGarage 2 жыл бұрын

Vector: i have the fastest 3D printer, with odrive bldc motors This guy: hold my klipper firmware

@247printing 2 жыл бұрын

Thanks for this comment! Would you like to tell me who Vector is? Edit: Found him - I like this channel 😍

@247printing 2 жыл бұрын

@@Lucas_sGarage I check it thanks a lot mate!

@VEC7ORlt 2 жыл бұрын

You rang?

@spacemandaxx 2 жыл бұрын

How to put 10 years of wear on your printer in 1 min lol. But seriously, this is awesome!

@247printing 2 жыл бұрын

Thanks man! The wear isn’t dramatic - I used the Voron Zero for 3 months now on the limit and it’s still in very good condition 😊

@foufou81 2 жыл бұрын

Why would there be any wear ? I mean, linear guides and belts can handle way more then this :) hihihi nice one anyway. The problem with high speed is the stiffness of the structure and the cinematic control (resonance, etc). Have you notice any strange behavior at these speeds ? Have you an example of the surface quality you manage to get at those speeds, acc and jerk parameters ? :)

@247printing 2 жыл бұрын

@@foufou81 I’ll upload a full print and showcase at those parameters this weekend - if I am lucky this could be the 1000subs @ 1000mm/s special print 😍

@DeltaCodex 2 жыл бұрын

@@247printing this is awesome, guess I'll be your 981st subscriber then

@247printing 2 жыл бұрын

@@DeltaCodex very very cool, thank you!

@kde9910 2 жыл бұрын

We need this to run vase mode printings just going in circles at max speed.

@247printing 2 жыл бұрын

Would be interesting to see, I’ll try it out, but shouldn’t be harder then this print 😊

@jackgaming0592 2 жыл бұрын

Those stepper motors must have some high accuracy!

@labemolon5739 2 жыл бұрын

This reminds me of a soldering integrity lesson I once taught my employees a while back. Excellent job on your soldering integrity!

@247printing 2 жыл бұрын

An awesome anecdote, I really enjoyed it! Thanks for that! Proper wiring, soldering and crimping is absolute key for reliability - I also had to learn it the hard way! Lots of failures!

@ChimpyChamp 2 жыл бұрын

How awkward would it have been if it snapped off and broke one of their noses? not going to lie if my boss whipped something heavy like that past my face it would end up around his neck.

@ChimpyChamp 2 жыл бұрын

@@labemolon5739 "But you wouldn’t work for me without a psych evaluation and background check and that type of behavior would have been identified in the background check by an ex or a relative." Now contrast that with what you said earlier. "I asked my employees to gather round a close circle. I then grabbed some wires and started spinning the sensor around fast enough to hear it whipping by and spun it in front of all their faces and yelled" And... "I anticipated it to break. Same belief as in “don’t pull out a gun unless you intend to shoot it”." It is clearly obvious that despite your loyalty to your staff you still have no problem putting them into degrading situations as if you have somehow gained (or purchased) the right to put another person in that situation...I can say for sure is that it wouldn't matter if you "paid my mortgage" or let me smoke pot during my break, I would not let you do that to me because I have some pride. If you think it's acceptable to abuse your power like that then don't be surprised if someone abuses you back in another way. It's common sense.

@labemolon5739 2 жыл бұрын

@@ChimpyChamp just enjoy 3d printing 👍🏻

@side2k 2 жыл бұрын

Imagine what huge effect such approach would have in schools!!! If teacher gets a whip, and start asking question, using the whip as response to wrong answers! Waaaait a minute...

@dennisdecoene 2 жыл бұрын

Most insane thing I've seen in years. Kudo's man!

@247printing 2 жыл бұрын

Oh thanks mate! That’s really nice to hear… there is a lot more to come!

@individualone 2 жыл бұрын

Holy mother of God! That's fast💯💪😆I luv it!

@HyperMakes 2 жыл бұрын

This is so unreal..!! Great job man 🤗

@247printing 2 жыл бұрын

Thanks man!

@boryshacker 2 жыл бұрын

Wooo this is nice! Great job!

@247printing 2 жыл бұрын

Thank you!

@dguy-xk4fc 2 жыл бұрын

You might consider upgrading those belts with metal guides and ball bearings before they explode, but amazing anyway. Very cool.

@247printing 2 жыл бұрын

Thanks a lot man!

@MarcoPon 2 жыл бұрын

So relaxed!

@danielfoxlab2168 2 жыл бұрын

omg, this is insane.... well done!

@247printing 2 жыл бұрын

Thanks Daniel 🤩

@BenMillen 2 жыл бұрын

Bronze and black looks great

@markomantere6437 2 жыл бұрын

This is insane!

@electronic.delirium 2 жыл бұрын

Waouh ! Impressionnant !

@efremtommasi1387 2 жыл бұрын

This is sick

@TREXFREAK28 2 жыл бұрын

It took me a while to figure out, that this is not sped up.... Good job - i am starting to get a bit jealous.

@agapiosagapiou 2 жыл бұрын

Let's set a new goal! The speed of light! It looks like is close to! Nice job!

@247printing 2 жыл бұрын

Thanks a lot :) I try to hit it :D

@santiago13ful 2 жыл бұрын

this scares me, but it's amazing

@fookingsog 2 жыл бұрын

Talk about Breaking Wind!!!😳 I was expecting a Sonic Boom to happen at ANY MOMENT!!!💥💥💥

@247printing 2 жыл бұрын

This would be so awesome... 343200 mm/s :D

@PhG1961 2 жыл бұрын

Amazing and very impressive!

@247printing 2 жыл бұрын

Thanks buddy!

@davisdiercks 2 жыл бұрын

WHAT IS THIS MADNESS

@cyberplant 2 жыл бұрын

at the final part it sounded like bossa nova.. I like it!

@thetinkerboys14 2 жыл бұрын

When the slicing software has to correct for Gforce 😂.

@247printing 2 жыл бұрын

True! Thanks to resonance calibration on the firmware!

@psydemekum 2 жыл бұрын

DUDE! AWESOME!

@247printing 2 жыл бұрын

You are awesome! I dig your nickname!

@highlander5521 4 ай бұрын

Deine Videos laufen bei mir immer doppelt so schnell ab XD

@247printing 4 ай бұрын

Das kenne ich - beim bearbeiten komme ich kaum mit!

@steffen1182 2 жыл бұрын

no need for part cooling fan! 😁

@evilborg 2 жыл бұрын

Holy mother of speed... its on speed for real!!

@Bpositive38 2 жыл бұрын

One step closer to the star trek replicator - Looks absolutely insane 🤪👏 .... but I wonder what the surface quality will be like!?

@247printing 2 жыл бұрын

Exactly this! I hope we’ll see the Replicator in our life time! I’ll upload a full print video with quality check in the weekend 😊

@MatthewHeiskell 2 жыл бұрын

I wanna see this thing in vase mode! Incredible!

@247printing 2 жыл бұрын

Thanks mate! I did some testing on printing 1100mm/s on vase mode - have a look at the Shorts video I uploaded! There is going to be uploaded a 1000mm/s full print (vase mode included!) this weekend 😬

@B0CT0K 2 жыл бұрын

*relaxed printing* printer: I AM SPEED

@maxtester8824 2 жыл бұрын

IMPRESSIVE!

@247printing 2 жыл бұрын

Max, YOU are impressive! Thanks for commenting 👍

@larryssuperhomearcades 2 жыл бұрын

200,000 units are ready, with a million more well on the way

@nife3557 2 жыл бұрын

Not everyone gets Clone Wars references :-)

@chinchan9 2 жыл бұрын

Printer Goes BRrrrrrrrrrrrrrrrrrrrrrrrrr

@uploader11459 2 жыл бұрын

This is insane

@MikeJones-mf2rt 2 жыл бұрын

Epoxy cement base and fill inside of entire frame for greatly improved vibration dampening

@247printing 2 жыл бұрын

Nice idea, I’ll think about that!

@landsurfmarin 2 жыл бұрын

Damping, not “dampening”

@MikeJones-mf2rt 2 жыл бұрын

@@landsurfmarin Autocorrect lol

@littlesnowflakepunk855 2 жыл бұрын

man, i really wish these vibrations were slightly, unpleasantly wet

@SexyEarHair 2 жыл бұрын

Now thats what i call rapid prototyping

@electricpaisy6045 Жыл бұрын

It looks so fast on a printer you almost can't follow with the eye when it's actually just the speed of a slow walking person.

@247printing Жыл бұрын

This is what blows my mind every time I think about it 👍 Relations…

@carsonbeaner4822 2 жыл бұрын

Imagine how fast vase mode would be Edit: watched the whole print and it actually is in vase mode

@247printing 2 жыл бұрын

You don’t have to imagine - you can watch it - it’s crazy! Please have a look at my other videos ☺️

@THEEVIL969 2 жыл бұрын

Rayos 😦 me quedé impresionado

@ChrumkavySuchar 2 жыл бұрын

Insane.

@metacreator 2 жыл бұрын

Please make a speed benchy on this machine.

@247printing 2 жыл бұрын

Incoming… will be really fast!

@FLMan180 2 жыл бұрын

Do this please I just subbed 👍👌

@247printing 2 жыл бұрын

I plan to publish the video on sunday 😬 it will be a loud print, it will be quite ugly and it will be the fastest on record 🙊 Also working on the fastest quality benchy on this machine - definitely clearly below 10min 😬

@FLMan180 2 жыл бұрын

@@247printing looking forward to watching it !

@onerob4141 2 жыл бұрын

So looking forward to this! Subbed...

@MichielvanderMeulen 2 жыл бұрын

bless the rounded corners

@247printing 2 жыл бұрын

No problem to do square corners! I liked the effect of the tool head rushing out to the fast straights when doing solid infills :)

@MichielvanderMeulen 2 жыл бұрын

@@247printing pretty spectacular! what acceleration values do you achieve?

@teac117 Жыл бұрын

After watching all these Voron speed tests, I understand why youtube is now recommending the woodpecker on metal videos.

@suriyasb5200 2 жыл бұрын

Awesome..!

@jerrylindstrom3323 2 жыл бұрын

Sounds like a laser gun :D cool video

@247printing 2 жыл бұрын

This is the best description for the sounds here! Pew Pew!

@Croolsby Жыл бұрын

Thanks!

@michaeljones5681 2 жыл бұрын

Don't have a 3d printer but this reminds me of the brother pr670 embroidery machine just a lot slower

@gunnerkobra 2 жыл бұрын

Its gotta a nice rhythm.

@247printing 2 жыл бұрын

Absolutely true - I love fast FDM music!

@greenyelectronics 2 жыл бұрын

wow! that's fast

@247printing 2 жыл бұрын

Thank you! More incoming :)

@user-ik1vz1hf5v 2 жыл бұрын

Monster 👍

@247printing 2 жыл бұрын

Indeed, little baby monster 😬

@NathanCroucher 2 жыл бұрын

Awesome

@RobertD_83 2 жыл бұрын

Absolute insanity in the best possible way! The voron people have designed a great platform and your build is frickin awesome, kudos! Edit: I looked to see if you have anything more in depth about it but mostly only found ~ 30s - 2m videos. If you plan to put out more about it I'd gladly sub the channel.

@247printing 2 жыл бұрын

Thanks Robert! Yeah I am working hard on a deep dive series concerning speed printing - I underestimated the efforts and time doing these, but those videos will be done and uploaded - just a matter of time! Please have a look at the description.

@Mr6Sinner 2 жыл бұрын

Those wires look like me on a floaty while my dads driving the boat

@247printing 2 жыл бұрын

Initially that was a work in progress video for the speedboat community - cable sleeves are a must here. But I like the picture a lot you described 😂

@u9Nails 2 жыл бұрын

3D.-1D Printing. The dimension subtracted is time!

@247printing 2 жыл бұрын

This!

@TheRainHarvester 2 жыл бұрын

Nice! I'm making progress on my inkjet dc encoder motor 3dp. It's fast, but loud when converting step/dir to the encoder/pid because it needs to brake to avoid overshoot every tick. Do you use encoders? Geared down? How do you avoid noisy braking?

@TheRainHarvester 2 жыл бұрын

You can see the videos on my channel.

@247printing 2 жыл бұрын

I’ll have a look, sounds very interesting! I am using Nema14 motors on tmc2209 stepper drivers here - really not fancy in comparison to what you are on to!

@judeevans8303 2 жыл бұрын

yoooooo!!! look at it move!

@247printing 2 жыл бұрын

This little crazy monster 😬

@Sanchogus 2 жыл бұрын

С такой скоростью даже обдув не нужен - потоком от осей отлично охладит :)

@randomhk8634 2 жыл бұрын

My next built

@ZeshXD 2 жыл бұрын

god that's fast.. i can't imagine the state of the belts after some days of printing :O

@247printing 2 жыл бұрын

They are performing really well!

@ZeshXD 2 жыл бұрын

Wait that's made to perform like that?!

@Unmannedair 2 жыл бұрын

Wow, that's pretty impressive.

@247printing 2 жыл бұрын

You are impressive!

@Unmannedair 2 жыл бұрын

I'm building a 2m printer and I've got to be able to hit these speeds as a matter of practicality. Nice to know it's an achievable objective.

@247printing 2 жыл бұрын

@@Unmannedair ok. That’s impressive! You should have enough room to accelerate to this speed and more. I bet you’ll do good motor choices and opt for 48V - no problem to reach 1200-1500mm/s!

@Unmannedair 2 жыл бұрын

@@247printing yeah if the heater can keep up with it. Problem is it's only easy to hit those speeds in a straight run on a straight part, if you're trying to do detail on that kind of scale there's massive acceleration problems. I'm pretty sure I'm going to have to create some custom slicer code in order to deal with some of those issues. I was also thinking about shooting for 72 volts because it's an industrial standard and it's easy to find power supplies for that voltage. I'm definitely going to need heat sinks on my stepper motors, LOL

@247printing 2 жыл бұрын

There are viable options to achieve the speed/acceleration, extrusion and the cooling. Weight is a topic on your big printer - gantry has to be designed as light weight as possible. And there is the motor topic. Big servos could be a choice for you. Concerning extrusion, a Mosquito Magnum Plus would be up to the heating (up to 100W) and extrusion rates you need for high speeds. The cooling should not be a problem on a printer aimed at big size prints! What are your plans on the project ? I am really interested!

@KobraVR 2 жыл бұрын

I can only imagine my Devon rex around this thing

@stockracingclub1414 2 жыл бұрын

Wow thats fast

@davidbarton3976 2 жыл бұрын

Here I am thinking I'm pushing my printer at 60 mm second lol

@247printing 2 жыл бұрын

I hope the manufacturers are ready for the speed revolution - not too mach to do for them!

@rikilshah 2 жыл бұрын

How fast can you print? Yes.

@247printing 2 жыл бұрын

Oh yes 😍

@dnettoRaw 2 жыл бұрын

if you try to put it in a vacuum chamber to reduce friction with the air, and use mineral oil to cool the hotend and the motherboard, but I have no idea how to cool the part itself

@247printing 2 жыл бұрын

Oh man, I love thinking about topics like these! Thanks for inspiring!

@truantray 2 жыл бұрын

Air friction is not an issue.

@dnettoRaw 2 жыл бұрын

@@truantray oks sorry :-/

@iwanawithyou 2 жыл бұрын

sounds like a slowmotion sound effect :D

@satina1169 2 жыл бұрын

Yup I want one

@247printing 2 жыл бұрын

Go for it! The kits (aliexpress, see video description) are getting better and better!

@TFlorian 2 жыл бұрын

You should turn your slicer to "vase mode" if it's 1 wall build (preventing stop, direction change and may be micro nozzle motion on each layers)

@247printing 2 жыл бұрын

Yeah, I tried two walls for that video. Full print of that - Vase Mode part of That - This evening right here!

@eddypdeb 2 жыл бұрын

@@247printing you can still use vase mode with parts that have thick walls. There is a video of a guy explaining it. The key is you have to take into account the thickness of the nossle and "draw" the route almost complete with a cut-in of just 2 thicknesses (one inbound, one outbound) so you go to the interior perimeter, then modify the interior perimeter to do several trips just near the outer wall to the thickness of the nossle. It creates a very stiff print and is going to be fast on this printer.

@247printing 2 жыл бұрын

@@eddypdeb the limiting factor on thick walls printed on Vase Mode is the throughput of the extrusion system at that speed. With my high flow config (mosquito magnum with long heater block) I am quite on the limit doing 0.1mm layer height, 0.4mm single wall at 1000mm/s. I recently uploaded a Vase Mode preview on this. From calculation it would be possible to do a 0.8mm thick wall at 500mm/s. Which still would be fast, but not 4 digits fast 😊

@walterincardona4187 2 жыл бұрын

I don't know why but I can't stop laughing ahaha love it

@dirk.o4424 2 жыл бұрын

really impressive I like it very much. This is how fast all FDM printers should be. I just think that the fans can keep up with the fast vibrations for a long time. And a big disadvantage is that the Voron V0 only has 120mmx120mm. Unfortunately😔

@247printing 2 жыл бұрын

The size of the V0 is both advantage and disadvantage. I consider it as a "secondary printer" :)

@deniseduardodonadontorres3698 2 жыл бұрын

How I though my printer would print when I bought it about 6 years ago.

@247printing 2 жыл бұрын

Same for me… the result was quite disappointing 🙊 but tech is here to go faster now

@steven664700 2 жыл бұрын

insane

@247printing 2 жыл бұрын

Thank you!!

@DanielGlock_1978 2 жыл бұрын

And your belts don't fall off,lol...my V0 doesn't like it,lol... it's getting jealous,lol

@247printing 2 жыл бұрын

The x-rail likes to fall off unfortunately😅not designed for these accelerations and impulses 🤓

@byronstewarcubidesromero6334 2 жыл бұрын

¡Qué bestia! Muy buena máquina, ¿cómo calibras todo para llegar a esa velocidad?

@247printing 2 жыл бұрын

¡Muchas gracias! Lo explicaré pronto en una serie de videos, pero será en inglés.

@Madthrax23 2 жыл бұрын

Even at this speed it's still slow ! xD

@247printing 2 жыл бұрын

True! We have to go even faster 🔥

@Tristan559 2 жыл бұрын

That beat tho

@jesstheheathen 2 жыл бұрын

Oh man. I want to build this.

@247printing 2 жыл бұрын

I can recommend it... Do it! These printers show the real capabilities of FDM-printing.

@heckyes 2 жыл бұрын

The E-steps she tells you not to worry about.

@KenTheJr 2 жыл бұрын

Any chance you can just drop a BOM so I can go buy exactly everything? Lol! I want it now!

@247printing 2 жыл бұрын

Coming soon! Still testing the designs and components. But you can start building your Voron Zero at vorondesign.com

@NoSupports Жыл бұрын

0:21 Good beat!

@dummypg6129 2 жыл бұрын

Short title: 3D Printer goes brrrrrrrrrrrr

@247printing 2 жыл бұрын

I totally dig that!

@Nitram_3d 3 жыл бұрын

nice

@247printing 3 жыл бұрын

Your hotend is nice

@medyk3D 2 жыл бұрын

0:02 Looks like a glitch in matrix :)

@Gr8Success 2 жыл бұрын

sheeeet... that's crazy ....

@247printing 2 жыл бұрын

Indeed!

@lepoloo 2 жыл бұрын

Wow!

@247printing 2 жыл бұрын

You are wow! ☺️

@rizen3467 2 жыл бұрын

when you let a kid drink coffee for the first time

@247printing 2 жыл бұрын

Very nice analogy!

@user-ye7cq4uv1t 2 жыл бұрын

wow... great video! what motors and firmware are you using?? and belt is gt2?

@247printing 2 жыл бұрын

Please have a look at the description 😊

@fkingride.5500 2 жыл бұрын

WTF! HOW? WOW!

@247printing 2 жыл бұрын

Don’t worry, my video series „Deep Dive to Speedprinting“ is incoming - I explain all the how’s and why’s 😊

@Zugirf 2 жыл бұрын

Does this affect print quality? What about the lifespan of the printer? Awesome video

@247printing 2 жыл бұрын

Print quality: Yes, definitely! Please consider this as a feasibility study :) Lifespan: The printer is 3.5months old. I am not able to judge the lifespan yet, but so far the wear in relation to the torturing is negligible!

@mtiger5 2 жыл бұрын

Holy shit, I’m new to 3D printing and see this thing blazing through a print unlike anything I’ve seen. I just ordered a prusa mini+ looking at KZfaq for tips and tricks … this obviously ain’t one of em lol

@247printing 2 жыл бұрын

I just wanted to write: „Welcome… to the hell of optimization!!!“ but… you ordered a Prusa… My MK3S+ still is (despite all this speed going on) my favorite printer, because it just WORKS conveniently! Very good choice 👍 maybe you won’t need Tipps and Tricks ;)