#145

Рет қаралды 2,614

5 ай бұрын

As this tractor came to us already partially dismantled we never got to dismantle the governor mechanism, so in this video we work through the full end to end governor mechanism and do the initial setting up as per the Service Manual.
KMP Brand (formerly Anglo-Agriparts) supplied the carburettor - their part number: A67694
Please visit their website for spares, tips and advice:
www.anglo-agriparts.com
Waterhouse Forde is our channel sharing the various projects we get up to as a family. The current project is the restoration of this Ferguson tractor. We invite you to subscribe to the channel so you can follow our progress. Feel free to comment as well, we love to hear what you think and of course we are eager to learn from your experience and know-how. Don't forget to click the bell icon when you subscribe so you get notified when a new video is published.
Thanks for watching.
Music:
Feelin' Good www.purple-planet.com

Пікірлер: 10

@nickrolfe367 5 ай бұрын

Hi thanks for posting this have started to do mine, I was laughing to myself when you first put the carb on, I did a similar thing when putting the dash back together as it has to be in a certain order.

@WaterhouseForde 5 ай бұрын

Hi Nick - I was so certain I had it the right way too! 😂 Good luck with yours - I hope this helps in some small way. 😉👍

@Masseyferguson65 5 ай бұрын

Good morning .. Wery interesting video .Nice to See how all the levers and how They funktion .. I love it ..look like this old steam engines ..Many levers etc ..😊🚜 look like your choke lever was lose.. like you open troutle full but chocke dosent follow ...I can be Wrong and meby you can check next time inside garage .. I like your long videos its Abselute Perfect.. we are allso exaited now that you are Going to get closer to a FIRST START ....i wich you a great sunday..Thanks a lot. Michell norway 😊🚜👍

@WaterhouseForde 5 ай бұрын

Hi Michell, thank you! 🙏 Yes, very excited now. Watch for the next video! 😉😁 The choke is not yet connected, only the throttle lever. I will connect the choke only once the tractor is painted 😉👍😁

@dazsden 5 ай бұрын

Great video! Does it mention in the manual to leave the rod from the governor 90 degree rod with the ball joint on it connected when adjusting the screw to take the free play out on the distributor side of the timing cover? It does make sense as the spring on the rod will keep the mechanism tensioned and it should be easier to feel the screw as it takes up the slack. And did you have the throttle set to idle while doing the adjustment on the screw?

@WaterhouseForde 5 ай бұрын

Hi Dazsden, thanks for your comment. The procedure I have is to disconnect everything and set each item in sequence. At idle, the spring should be loose, it only comes under tension as you move off of idle. The screw on the timing cover is pushing up against a length of spring steel which in turn provides some ’play’ between the lever and the centrifugal mechanism on the pulley. You do want to keep the lever in the “idle” position while adjusting the screw tho. Hope this helps 👍😉

@dazsden 5 ай бұрын

@@WaterhouseForde thanks for that reply! Looking forward to hearing it cough into life!

@jerrymoore7669 5 ай бұрын

That govener setup looks the same as my old to20. The top spring on mine is different. One end is longer that hooks to the small linkage. I am not sure that it is right on mine. It could have been changed over the years. I can email a pic or a video clip if you need to compare.

@WaterhouseForde 5 ай бұрын

Hi Jerry, thanks for your comment. It’s possible that the spring may have been changed, either by Ferguson or anyone else since it left the factory 😂. It would be interesting to see yours if you’re able to send a photo. Email address is: waterhouseforde at gmail dot com 👍😉

@WaterhouseForde 5 ай бұрын

Aha - well stay tuned! That will be the next video - Hopefully! 😉