150hp Fatbob / 128ci Alpha Performance Engines

Рет қаралды 11,326

Жыл бұрын

I finally went racing again thanks to Alpha Performance Engines!
Mark hooked me up with a 150+Hp Fatbob to have some fun on & I did just that.
When the bike arrived it had a 2'' Arlen Ness Air Filter & a FREEDOM Radical Radius 2-2 Exhaust system. I put it straight on the Dyno & reeled off an impressive 151hp & 155ft/lbs.
PLEASE SEE THE VIDEO LINK BELOW THAT SHOWS THIS BIKE ON THE DYNO & I TALK ABOUT & PROOVE JUST HOW MUCH ALTITUDE EFFECT PEAK HP & TQ NUMBERS ON DYNOS.
Link to video, Fatbob being dynoed & altitude talk.
fb.watch/k7n-Gc34O3/?mibextid...
I had a D&D Bobcat 2-1 on the shelf doing nothing so I fitted that up along with a Screamin' Eagle Heavy Breather Extreme. I was very rushed for time & only spent about half an hour giving the bike a quick 're-tune' with the new exhaust & air filter & managed to get the same numbers, there is definitely a few more HP to be found in there but for the day I went racing I was not worried about a couple numbers.
I want to thank Gasoline Alley Harley-Davidson for sponsoring the Willowbank 'Race Ya Mates Day' & all the staff at Willowbank Raceway for ensuring the day runs smoothly!
Huge shout out to Mark & Alpha Performance Engines for the bike to have fun on too!
If you want to ride this bike, feel free to drop in & see me at Darling Downs Harley-Davidson. You will not be disappointed.
Please leave any questions in the comments & I will get back to you asap.
Follow me on Instagram / tommy_twincam_miller
I work here ddhd.com.au/
You can call me on 0746342766 during AEST business hours.

Пікірлер: 58

@TrustyZ900 27 күн бұрын

150 hp right heeah. Sounds delightful.

@darrenmckenna9115 3 ай бұрын

Thanks mate awesome work and great riding

@robertfagan8833 Жыл бұрын

Love watching your channel.. you produce beautiful builds..

@MasterTechMiller Жыл бұрын

Thanks for watching & enjoying the content

@MickOTooleroadglide Жыл бұрын

Awesome one Tommy congrats on the great passes mate

@MasterTechMiller Жыл бұрын

Thanks mate! Always wishing I could've went faster but that the point of racing I guess

@williamb.9110 Жыл бұрын

Very nice!

@scotttickner1662 Жыл бұрын

Thanks for the video Tommy. Must be awesome to have a boss like Mark, you must skip into work 😂.

@MasterTechMiller Жыл бұрын

I do feel pretty lucky to have 'job' that I literally feel like I never work a day in my life.

@scotttickner1662 Жыл бұрын

@@MasterTechMiller Just got off the phone to Mark and ordered a stump puller kit with the 485 cam for my 2019 breakout. Thanks to your you tube channel Tommy 👍.

@MasterTechMiller Жыл бұрын

@Scott Tickner great stuff mate!!!

@351kostakis Жыл бұрын

Fantastic

@thorout8377 Жыл бұрын

Im liking the fatbob. I have a 21 breakout that i love. But as far a racing on a circuit track. The fatbob is choice.

@bc1953 3 күн бұрын

That HP to low weight gotta be fun ! what was the cost for the build out to get to that HP ?

@mickrose6450 Жыл бұрын

👊🍻

@moulis05 Жыл бұрын

Some good passes mate. How good is the gopro footage!

@MasterTechMiller Жыл бұрын

Turned out awesome 👌

@greggatto1428 Жыл бұрын

RIPPER!!

@timrodeheaver9167 2 ай бұрын

Awesome video, I hope to have my breakout at the drag strip soon. It is making 148/15 with the CR5155 cm and 128 kit. I have clutch springs but im so worried about breaking the compensator, clutch basket or belt. Does this bike have those parts upgraded?

@MasterTechMiller 2 ай бұрын

Thanks for watching. Yes this bike has the upgraded comp ramp & is running SE 1275nm clutch springs. Clutch is otherwise completely stock. Still running the OEM Drive belt too.

@timrodeheaver9167 2 ай бұрын

@@MasterTechMiller That is great to hear. I am so worried about breaking that stuff but im ready to go chain drive and all that stuff.

@noahperius8291 Жыл бұрын

Awesome video! What helmet are you wearing?

@MasterTechMiller Жыл бұрын

Biltwell. Lane Splitter

@fxdls-8201 Жыл бұрын

Awesome! Hey mate I’ve got a 23 fxlrs, a 131 with 155hp, 165 ft lbs What times do you think it should run? Obviously rider depending lol

@MasterTechMiller Жыл бұрын

Low 10s mate.

@fxdls-8201 Жыл бұрын

@@MasterTechMiller happy days, thanks for the reply. Love the content 👌

@robertshuttleworth Жыл бұрын

Rob from NZ here was just wondering what cam would be the best for a 2022 sport glide I feel its lacking punch in the lower revs I thought more torque down low maybe your thoughts would be great cheers

@MasterTechMiller Жыл бұрын

Hi mate. The 107ci responds well to the CR480 from Cycle-Rama

@robertshuttleworth Жыл бұрын

@@MasterTechMiller cheerz

@briannorwell202 Жыл бұрын

What would you say regarding a comparison between the CR540 and the CR515 from APE ? Is the required compression different between the two cam?

@MasterTechMiller Жыл бұрын

The 540 will produce over 160hp with the right combination of parts & comp ratio. It generally needs at least 12.0:1 to work properly. It does have quiet a bit of valve train noise though. The CR515 will produce over 150hp but has less lift which results in less stresses on the valve train which in turn has quiet operating noises. The CR515 responds best at 11.5:1 & up. The torque of the 515 comes in nice & early depending on exhaust choice.

@m8_fanatic Жыл бұрын

Hey mate, im contemplating a 128 or 132 build. I have an fxdr 117 stage 4 heads, 64mm throttle body, extreme breather at the moment. I also have a cr485 cam ready to go in , would love to know your thoughts on a build and where to go from here?

@MasterTechMiller Жыл бұрын

If you already have the SE CNC ported heads & 64mm Throttlebody that's a great start. The CR485 Cam you have loves higher compression ratios. The 128ci kit from Alpha Performance Engines is 11.0:1 The SE 131ci kit is 10.7:1 Keeping in mind the 128 is obviously 3ci smaller but has a higher comp ratio. It will make more power with the 128ci kit than the 131. The 131kit will produce a little more torque due to the larger displacement

@m8_fanatic Жыл бұрын

@@MasterTechMiller awesome mate, ill fit the cr485 this week, get her dyno tuned then start saving for the big bore! Love your vids and your work from here in Nz.

@MasterTechMiller Жыл бұрын

@@m8_fanatic let me know how you go

@rawirilawson3162 10 ай бұрын

hi great content built my bike off your vids Have 2022 lowrider s 131kit CR512 cam CR billet compensator heavy duty clutch springs Screamin eagle heavy breather extreme screaming eagle camplate and oil pump 7.1 injectors already had a TBR exhaust was built at Road and Sport Hamilton NZ Dyno 150hp 164tq super happy with those numbers first drag meet in November Do you think i will need to do a Chain Converstion this is my daily ride but will be doing about 9 drag meets through the season dont want the extra expense but will run a shinko tyre on a prep track do you think my belt would hold up

@rawirilawson3162 10 ай бұрын

Did the fat bobs belt hold up?

@user-ux9nt1qd5h Жыл бұрын

Hi tommy love our video I would like to do a build I got 21 road glide I think on screaming eagle 31 stage 4 our do you think 128 from ape would be better do not care on big numbers want good fun bike and reliable would like what you think 16:37

@MasterTechMiller Жыл бұрын

The best bang for buck combo you can do is the APE 128 Stump Puller kit. We can speak more in detail & work out your exact needs and requirements. Email me at workshop@ddhd.com.au

@user-ux9nt1qd5h Жыл бұрын

Thanks for getting back to me and I will email you thank you

@TrustyZ900 6 ай бұрын

675 pound bike and runs mid to low 10's. Imagine if it was the weight of an MT10. 9's for sure.

@MasterTechMiller 6 ай бұрын

💯

@trevor_leonard Жыл бұрын

What’s a rough estimate of the full cost of this build?

@MasterTechMiller Жыл бұрын

If you already have a full stage 1 kit with a tuning device this build will be around $7500aud ride in ride out

@charlesmccurry3602 4 ай бұрын

515 or 540 128 s&s same throttle Body two into one krome works outlaw no head work 11 to 1

@troydroberts88 Жыл бұрын

I want one.

@MasterTechMiller Жыл бұрын

This one will be for sale in the near future.....

@fabianvalencia-zo3oh 9 ай бұрын

How’d you get your fat bob to pass 120 mph? my ‘22 fat bob is limited to 4.5k rpm’s in 6th and won’t go farther.

@MasterTechMiller 9 ай бұрын

Turning the speed limiter off via the tuning software/device. There is an option to turn it off with Technoresearch. If you are using power vision there is a selection in 'limits & switches' within the software.

@inteligentvtec Жыл бұрын

I have a Harley but would never spend a dime on trying to make it fast, it's a cool bike how it is. Just put exhaust and a tune on it. You can spend a fortune and it's still not fast. My zx6r is bone stock just lowered and runs 9.96 at 138. Save your money.

@truckerruss5764 Жыл бұрын

Takes nothing to ride a bike fast that's made to go fast. For some it's more of a challenge and more enjoyable to build and ride something fast that wasn't really meant to go fast. I get way more enjoyment riding my SG hard than I ever did my 1000cc crouch rockets. But hey, we all ride for our own reasons.

@allan9584able Жыл бұрын

I have couple question for the Master tech if possible bro,what your thoughts on 114 to 122 kit with a 30/30 cam the comp ratio on them is 11:1 would run 5.5 injectors and 64 mm manifold throttle body ? And the second what set up would S&S roller rockers be suited too, as there different ratio to standard ,was told on a 30/30 cam no good give to much Lift?

@MasterTechMiller Жыл бұрын

I finished our shop demo a few weeks back running the 114 to 122 kit with a D&D Lowcat & the CR485 Camshaft. It made 139hp & mid 140s in torque. I've used the 30/30 cam both in 107 & 114 applications & I was left underwhelmed when compared to what the CR485 does in a 114ci. The 485 out performs the 30/30 in my experience & opinion. There is no need for the roller rockers when using the smaller lift cams so I wouldn't bother. The only time they should be considered is when maximum lift is being chased & the you need to reduce side loading of the valve stem

@allan9584able Жыл бұрын

@@MasterTechMiller ok mate Thankyou for your experienced advice Appreciated, But the CR485 inlet valve closes at 36 where the 30/30 is 25 so you would lose low end torque with the CR485 cam but have room to grow compression. Correct on a 114

@allan9584able Жыл бұрын

@@MasterTechMiller roller rockers would be a benefit if you could get same ratio as standard as its simple they better lubrication and less friction less heat more Horsepower .

@MasterTechMiller Жыл бұрын

@4 happy family members intake closing time is not something I would base my low end torque expectations from. The lobe separation angle is a better indication of how the torque curve will look. Duration is also another factor. I agree with you about if stock ratio roller rockers were available however the gains out lined by you would be minimal in the M8 platform and while they may be picked up and measured on a dyno I highly doubt you would feel the difference

@allan9584able Жыл бұрын

@@MasterTechMiller agree not feel the difference but the engine would in longevity

@allan9584able Жыл бұрын

😂