1944 Allis Chalmers B

1944 Allis Chalmers B - Part 7

Рет қаралды 5,235

Күн бұрын

Part 7; Cold compression test, warm compression test, cold start, starter check, grease zerks, battery box, front wheel bearing check, flat spots on tires, bent rim, engine oil change, transmission/differential oil change, final drive oil change, good oil pressure, mouse nest material, wasp nests rear axle housings, flushing transmission/differential system with diesel, final drive oil pans, final drive oil pan gaskets.
After sitting for many years this tractor is finally back to operational condition. It put up a fight every step of the way!

Пікірлер: 21

@AntiqueCarsandStuff Жыл бұрын

I finally got the old girl back to operational condition, but there were a lot of tedious issues left to encounter. Thanks for watching. I hope you enjoy it!

@ronaldwells1805 Жыл бұрын

Another great video

@brucejohnson4462 Жыл бұрын

I pulled the final drives off of my B last week. I had a mouse nest in one side and a wasp nest in the other as well. I bolted my final drives back on upside down. Now I'm modifying the front axel. Center pivot on my front axel is 9" from the floor. She's a low rider now. Like crawling down into a go cart.

@AntiqueCarsandStuff Жыл бұрын

Yes, all that open space in the rear axle area perfect for little creatures. Not the best design I'd say, but wonderful tractors!

@williamwallace7299 Жыл бұрын

I like the fact that you only speak when necessary. So many similar channels are filled with verbose individuals who have very little to say. Plus I love your own music!

@AntiqueCarsandStuff Жыл бұрын

Thanks! I did not use my own music for this video but will definitely slip some in for the future…

@terryraymond7984 Жыл бұрын

Black Gear Oil Buggers

@dennisburcaw7158 Жыл бұрын

Never seen a B that started so easy, I've actually bought torque tubes to install on starterless B's to have elec start.

@corneliusconijn881 Жыл бұрын

If you remove the trans side cover, a can of brake clean will do miraculous work, immediately.

@dirtbag7921 Жыл бұрын

Looks good.

@AntiqueCarsandStuff Жыл бұрын

Thanks my friend.

@Meglev21 Жыл бұрын

Zinc oil additive to protect cam lobes? If the cam was not new at rebuild, it should be ok as the metal would have previously absorbed zinc from oil.

@mattbalik2585 Жыл бұрын

I haven't seen Allie and America lately, I hope they are still with you and are doing fine!

@AntiqueCarsandStuff Жыл бұрын

Thanks for asking. 🐶🐶 They are almost 13 years old but are hanging in there! ❤️

@williamwallace7299 Жыл бұрын

You’ve got to show us the sickle bar in operation, please!

@corneliusconijn881 Жыл бұрын

Black honey!

@doughboy1966 Жыл бұрын

Those final drives are always messy changing out the oil.

@cousinfester4621 Жыл бұрын

You can use oil with a zinc additive in that engine. Your cam and lifters will thank you.

@AntiqueCarsandStuff Жыл бұрын

Good idea. Thanks.

@terryraymond7984 Жыл бұрын

Do those engines use the none-Detergent Oil, Like the Older John Deere's?

@AntiqueCarsandStuff Жыл бұрын

My personal opinion is this; I use non-detergent oil in my engines without traditional oil filters, and modern/detergent oil in the ones with oil filters.