You had me at PING "I wonder how important that was". 1994 Coupe owner here, working on my instrument cluster.
@ktecgarage Жыл бұрын
😁 Good luck with the repair!
@Sauceyjames2 жыл бұрын
This happened on my 99 civic, sometimes I was able to smack it to work, & sometimes it would work after long drives, but it would erratic. I thought I would have to solder something in, but I didn't know it just needed to be resoldered like this. Gonna give it a shot & see what happens!
@ktecgarage2 жыл бұрын
There are several solder joints around the the dial if the speedo that you should check as well. Good luck!
@BabyJesus4202 жыл бұрын
Glad I found this because my 95 Civic dx is doing the same. Actually went completely out for a week and then came back. Today it jumped to 120 and then back around to the under the 0 stopper
@ktecgarage2 жыл бұрын
If u pull the speedo, you should also reflow all of the welds around the dial as well. I wish I did that in this video too. Good luck!
@kcskunk42113 жыл бұрын
Got into my civic this morning for work and this problem welcomed me as I turned onto the hwy. Will check this out when I'm not hiding at work lol.
@elkayezs8wslkwaterfountain8263 жыл бұрын
im actually picking up a 92 with this problem tomorrow. so this is helpful as hell
@ktecgarage3 жыл бұрын
Let us know if this works for you. Good luck!
@elkayezs8wslkwaterfountain8263 жыл бұрын
@@ktecgarage i sure will. probably planning an attempt next week if i confirm that the speedo is being funky
@elkayezs8wslkwaterfountain8263 жыл бұрын
@@ktecgarage yup. speedos bad. needle was below pin so i had to flip it around using a magnet. since the cluster is out im reflowing the solder welds now
@lecongtri51134 жыл бұрын
You're doing a nice job bro, so useful, love this model of civic, so cool and main cluster beautiful. I'm driving 1992 accord with so much fun, just subscribe to support your channel
@ktecgarage4 жыл бұрын
Thank you for the support! I subbed back to you. I'm planning a quick video about this car and how well it is performing after 27 years. I also have a 2000 Accord featured in most of my videos so be sure to check those out.
@ysrcutoo13 жыл бұрын
Nice video dude..its quite helpful..i also have the same problem with my civic..will do repair tomorrow☺️
@ktecgarage3 жыл бұрын
Thanks! Hope your repair goes well. Let us know if it worked for you.
@ysrcutoo13 жыл бұрын
@@ktecgarage welcome bro..ok i will let you know about the results of repair🥰
@deniselectron94242 жыл бұрын
Did it worked? I'm about to do the same thing with mine
@rufusconnolly84893 жыл бұрын
Thank you for the video mate.
@ktecgarage3 жыл бұрын
Thanks for watching and commenting!
@dhonne08733 жыл бұрын
do you know the wiring diagram of speed sensor?
@ktecgarage3 жыл бұрын
Here is a link to the complete 93 Civic wiring schematic. It will let you download it PDF or just scroll through. The circuit your looking for is called VSS (vehicle speed sensor) Hope it helps. www.scribd.com/doc/109570773/Wiring-Diagrams-Honda-93-Engin
@Irregular-SAMK Жыл бұрын
Thank you brother!!!
@ktecgarage Жыл бұрын
Glad to hearthe video was helpful! Good luck
@cali_cal4 жыл бұрын
going to give this a try. thanks
@ktecgarage4 жыл бұрын
Good luck. Let's us know if it worked for you. Thanks for stopping by.
@EDGAR0728 Жыл бұрын
I will try the same thanks for this video
@ktecgarage Жыл бұрын
There are a ton of other solder joints on the speedometer too. If you take it apart, I'd reflow those as well. I wished I had shown that in this video. Good luck!
@yotamonster2 жыл бұрын
Thanks for this
@ktecgarage2 жыл бұрын
Glad it was helpful!
@rickyr42432 жыл бұрын
Good job..Indonesian Civic fans club.
@ktecgarage2 жыл бұрын
Hello, my friend. Thank you for commenting.
@onursozer55332 жыл бұрын
While in use, it goes full round by itself and gets stuck at 0. It doesn't go forward. Is the problem vvs or the indicator?
@ktecgarage2 жыл бұрын
If it's this vintage Honda, I'd say it was the solder joints being cracked. You can put a volt meter on the speed sensor and spin the tire by hand to test that.
@ddtheboss464 жыл бұрын
Thanks man you really help me out
@ktecgarage4 жыл бұрын
Glad to help!
@jessebennett78582 жыл бұрын
Thank you so much man your advice fixed it you save me from throwing money at this car lol
@ktecgarage2 жыл бұрын
I'm very glad to hear the video helped you out. Thank you for taking a moment to comment.
@aaronfry90192 жыл бұрын
Did you have to move the needle back at all because it would get stuck under the bar or did it just go back to normal when it worked?
@ktecgarage2 жыл бұрын
Mine would pop back counter clockwise even when it was jammed under the stop.
@ze_german29213 жыл бұрын
I don’t understand what is happening when you heat up the solder. How does the speed know?
@jessebennett78582 жыл бұрын
solder was old and cracked reheating it made a nice and smooth connection to the sensers
@strange43022 жыл бұрын
Hello my friend, I own a Honda 1993. My speedometer is stuck at 60 km. I don't know what to do to fix it. Do you have any information?
@ktecgarage2 жыл бұрын
If it doesn't move even when you shut the car off, you may need a salvage cluster. Hard to say for sure. Good luck
@wink215411 ай бұрын
Mine has a delay under 20kmh, then jumps all the way up to 30/40. Any thoughts?
@ktecgarage11 ай бұрын
If it works sometimes or erratically, then it's probably a cracked solder joint. If I redid the video today, I would also remove the speedometer from the cluster and show the solder joints on that part as well. I had broken solder joints in the HVAC head and master relay as well. Seems to be an issue with this generation. It could also be a speed sensor, but mine was the solder.
@wink215411 ай бұрын
@@ktecgarage thanks for the update. I'll be sure to check both, as im planning some extensive repairs.
@throttlefilms2 жыл бұрын
will my spedometer work again if i just get a new one?
@ktecgarage2 жыл бұрын
It is most likely broken solder joints if your car is the same vintage Honda. A new one will fix it if you can actually find one.
@orlandocabrera85 Жыл бұрын
How much would you charged for something like this?
@ktecgarage Жыл бұрын
Eh. I only work on my own stuff so I don't ruin someone else's! I do work on friends cars sometimes, but I always stress about it.
@orlandocabrera85 Жыл бұрын
I soldered it and it still doesn’t work. Or could I have a different problem?
@ktecgarage Жыл бұрын
If you take the dial assembly of the speedometer out of the cluster, you will see it has solder joints up and down each side. I would reflow them as well. This generation's solder joints crack everywhere. I had to do the main relay and hvac head joints too. Good luck!
@orlandocabrera85 Жыл бұрын
@@ktecgarage ok ok so correct me if Im wrong. I have to take the clear cover off first and then it’s I believe two Phillips screws on the back of the cluster (where I saw you reflowed some of the first terminals). And then (if I get it off first) your saying it’s on the sides, correct? Sorry😔 I feel like I’m clueless without pictures or videos
@orlandocabrera85 Жыл бұрын
Actually I took off the speedo it was actually 3** Philips screws
@orlandocabrera85 Жыл бұрын
Actually, nvm. Yeah, I had to re-solder the joints on the (black) connector cuz I had cracks on the joints. I followed the other KZfaq video of this. It works now! Thanks
@ktecgarage Жыл бұрын
Glad to hear you got it working.
@alyssal59262 жыл бұрын
Does this work with the 97?
@ktecgarage2 жыл бұрын
If cracked solder joints are causing your problem, then yes. The speedo should be pulled and ALL of the joints inspected with a magnifying glass. If you can bang it and it changes the way it functions, something is loose. Good luck!
@botflymaggotmaggot11942 жыл бұрын
0:49 yeah, you sure you have a nice gayrage
@killanoa Жыл бұрын
will this work for the gas level gauge aswell?
@ktecgarage Жыл бұрын
It could. Just depends on what's broke. Good luck!