√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

For anyone who’s having trouble with the bolts that hold the window in place, they are tricky, and require a specific method of removed which is not mentioned in the video. They sit on a track of threads that requires them to be unscrewed ‘twice’. Unscrewing the bolt from the first track is very simple. But once you’re on the second track you have to pull the bolt towards you and unscrew in order to remove it, or at least unscrew it enough to release the window. Specifically you have to pull the bolt towards you until it threads and can be unscrewed a second time. I used a shoe lace lassoed around the head of the bolt to pull it towards me while I unscrewed it with a ratchet. I’m sure there’s a better way but that worked for me given the tools that I had. Additionally when you’re putting the window back in, ensure it is positioned properly. If not it will fail to roll up all the way, or worse, result in your window tinting getting ripped off by the door.

Thanks for this high quality video, saved us hours fixing up our mini! A few comments based on our experience on a R56: To remove the glass - Remove the round surround from the internal door release handle as the video shows. Remember to pull out the locating pin first. - Unclip the main trim panel by prising it away all around the edges. It’s a a big U shape. No need to unclip the armrest cover. - Remove the two rubber covers to access the two bolts securing the glass clamps (it’s necessary to lower the window to the correct position as the video shows) As other having commented, getting the two glass securing bolts out is a major challenge, since they need to be pulled at the same time they are unscrewed. They have a short threaded section which engages with each side of the clamp as you unscrew them, so once the bolt has been unthreaded from the outer clamp, it floats around. Other have suggested looping string around the bolt head to pull on them. Once the bolts are out the glass can be lifted out. It won’t drop out since the clamps have ledges at the bottom. It should also be possible to remove the glass without needing to raise the window, removing the outer trim may help with this it it’s a tight fit. The bolts can be left partially threaded so you're ready for the glass to go back in. To remove the whole inner door panel (if for example you need to get to the lock mechanism), the glass needs to come out first. After disconnecting the wiring, the whole door panel can be extracted by removing just the 11 torx bolts around the plastic panel, the 5 on the aluminium strip and bracket, and the small nut and bracket on the stud. One of the bolts is under the rubber trim, which needs to be unclipped. There’s no need to remove the mirror switch and the surround over the smaller speaker, or the large speaker unless any of these have particular issues. These are bolted to the to the door inner plastic panel (door card?). not the door itself. You will need to unclip the armrest to access one of the 11 perimeter bolts. Finally unclip the door lock release cable from inner handle as shown in the video, then the whole panel can be removed.

These are the videos that make KZfaq absolutely brilliant great video keep up the work very informative thanks

Great video - thanks. My window won't come down as the regulator is broken. Does anyone have any tips about how to get it removed without getting it lowered to the access holes to loosen those nuts? Thanks.

Very good video well explained..nice.

Your videos are so professional and informative. Thank you A1 Auto's, I need to replace a blown speaker, and now I know how to do that! 👌👍

Very, very informative and a nice commentary with good photography.

Excellent video one of the best I’ve seen thanks so much for sharing this has saved me a trip to the workshop

This helped me out massively, thankyou.

Removing the door panel and the glass is a nightmare! This help me a lot. Very clear and well explained. Thank you very much for this demostrative video.

Fantastic instructions. Thank you.

Very helpful and methodical' ... thank you!

Great video, this helped make it so easy

Appreciate the video, very informative and well produced. You guys saved me over 500.00 and I got a chance to punch inflation in the mouth.✌️

Super travail très bien explique 😉

Aw maaan this is the best place to get knowledge about my Mini and how to service this car 😎

Thanks your video is great help.

Thanks you did excelent, thanks for the help. 👍👍

Very great vídeo. Thank you very much.

muchas gracias x el video me salvastes la vida !!!!!

Grazie di tutto, siete super

A very good procedure except: 1. the screws holding the window are T40, not T30 2. When the window wouldn't come out, you missed that important step as outlined by some posters already: you have to pull the screw out as far as possible until it engages in the oute part of the fitting and then unscrew it a coupke of extra turns. I used a magnet to do this

To remove and the back of the armrest, are there just a few torx bolts? Do you have a video showing that? Thanks!

Thanks for the video very useful, I assume there is no way to sounddeaden the door without removing the window pane? :(

Wow, Thanks bro

good job what gloves do you wear

Does the window have to come out? Just for the door panel, I didn’t see why it would need removed. If you could let me know I would appreciate it. Inner door handle stopped working on my daughters car and I was going to fix it. Thanks in advance.

Do i need to take the window out to access the inner door handle cable?

According to the Haynes manual, one should NOT attempt to remove the release handle trim like it's done 1 min of the video. Prise out the pin at the base of the trim, but wait until the complete door panel is off to remove the trim, if needed. Then you will have easy access to the trims fastening clips on the back side of the door panel.

What is the part number of the first clip that has to be roemoved?

Mini Cooper d 07,right hand drivers door,window not working can you please help me,thanks

I have to remove this panel on my Coutryman (R60) for replace the door light. Not an easy access, akward decision from conceptors for this door

Crazy design Totally over engineered Especially compared to the 02-06 models No need for all that guff 😖 This can be much simpler Great video by you though 👍🏽

Dont tighten window bolts too much!, I just had one shatter on me lol

What's the point of removing the glass? It is attached to the door panel anyway, so you can take it out in one piece.

The torque screws that hold the glass has 2 treads. In order to remove the glass you have to take them off completely. I am wondering why you skipped that step.

Sounds like John malcovitz (more than likely spelled wrong!)

I am talking about the part after 6:03 of the video. The bolts were just loosened and the glass does not come off. At this point I spent 30minutes to figure it out.

Why are you removing the window when it's the inter door panel that is being removed??

The door is broke and won’t open . How do I get the panel off if I can’t open the door ? I bought the car and the seller said he’d fix it but he won’t .

Wow these are just awful cars. Thanks for the help.

nice vid but we would like to see how you removed the speakers. anyways "that will do"! thanks

아놔..도어트림 뜯는데 유리탈거는 이런 지랄맞은 미니가 최초일듯

What is preventing window from being removed ,why do you not show this but just edit out !!!!!!! Why why. Is there anyone who knows how to do this !!!!!!!!??

What a night mare. I'm old school, where it would only take about 15 minutes to remove a door panel🤬🤬🤬🤬

What a load of work just to remove this ffs

Oh this is an extremely fiddly job to do…..

The backing music spoils an otherwise good video. It doesn’t add anything useful.