2.0 Vauxhall vivaro rear brakes and calliper removal

Рет қаралды 2,251

5 ай бұрын

Vauxhall vivaro rear brake, calliper and disc strip down and check over,
NOTE
if your unsure runs your to a garage to be fixed

Пікірлер: 17

@Enzo_dub 5 ай бұрын

good shout I need to do calipers because the handbrake part keeps sticking, may as well do cable while I'm there. keep up the video's 👌 waiting for a CV driveshaft fixingz video 😂

@tinker-time 5 ай бұрын

No worries 👍 do the lot cable and caliper all sort then, 👍 drive shaft? Which part do you want to do? Can't take any more off the van he's now nearly down to a bare shell there's more in the back of it then on it 🤣🤣🤣

@SMxAd 5 ай бұрын

Love your videos. Really informative down to earth stuff. Fantastic

@tinker-time 5 ай бұрын

Hey cheers 👍👍, for that 😉

@homer1033 5 ай бұрын

Cheers Mark for the heads up on the rear brakes, I've just overhauled the front end and the rear end is next ...so great video so i know what to look out for. Cheers Kev.

@tinker-time 5 ай бұрын

Hi kev No worries hope it some help, did forget to say about just unscrewing the Reservoir cap to let the air escape as the pistons are been pushed back in you'll probably know this doing the fronts anywhere 👍 Thanks for watching and subscribing 👍

@homer1033 5 ай бұрын

@@tinker-time Yes i undid the res cap when i did the front end, was going to say on your video you never showed that part lol

@vauny24 4 ай бұрын

Do a vidbl of changing the front lower ball joints, there fun too do

@tinker-time 4 ай бұрын

awful job mate, have you just done yours? do i 1.9 starter motor, total nightmare job, 🤦‍♂️

@vauny24 4 ай бұрын

Did mine few years ago, used the grinder to remove the stud heads then knocked them out, wasn't that bad of a job really key is to get the blow torch on the studs then knock them out, with the lower control arm supported so you can give them a good wack

@cozziekid 5 ай бұрын

Hi Mark, great informative video as usual. How would you go about getting that bearing nut off if it wont rattle off with a gun? Heard some right horror stories about them being F#@%ing tight and snapping 1/2" strongbars for fun & needing a 3/4 or 1" socket & bar, which i dont have!

@tinker-time 5 ай бұрын

Heat the nut up and then put some cold water on it straight way, and that will shock it. If you watch my video where I did my rear shockers, you will see how I did it, And thanks for the nice comment 👍

@paulmaxwell7238 5 ай бұрын

Hi Mark are you going to replace the back brake covers?

@tinker-time 5 ай бұрын

Yes mate, this side had it, other side ok 👍

@grumpygrandpa3640 4 ай бұрын

How many Vivaro’s you got ?

@tinker-time 4 ай бұрын

3 at the minute, but another one hopeful is coming for the channel help people out 👍

@OptiViewagency 4 ай бұрын

Hello Dear, I have already visited your KZfaq channel. and analyzed the videos. Your videos are great & very nice but your video SEO and optimization are very low. This is a big problem. Because of this your video is not getting views, likes, comments, subscribers and is not viral going .Video uploading is very important for SEO and properly promotion. KZfaq channels need SEO and video promotion. If you want, I can create a report on your channel growth . I am waiting for your response. Thank you