I've spent countless hours over the past couple years, not using a computer, but a graph, if you notice even the so called experts, end up swapping caps and coils, after all thier computer designs. Just buy a bunch of coils and caps and test test test, you can use cheap ones if your only building 1 set then build your final crossover with quality parts just use the Dayton caps thier cheap and sound better than the expensive ones Jantzen coils are probably your best choice for coils unless you want to spend a lot of money

Yes indeed

Thank you 🙏

thank you 🙏🙏🙏

Thank you 👍

🥰🥰🥰👍👍👍

Crossover cut frequencies not àdd frequencies!!! We can make equalisation modification on crossover but just for few decibels. You must check the ref of your driver on Internet to see the response diaphragm.

Thank you for your nice words, i do this because i love sound 😍😍😍 For 4ohm 6khz high pass try second order filter based on 4.7uf cap in serie + 0.2mH inductor on parallel, 0.5mh in serie + 10uf in parallel for low pass.

And sûre lpad for tweeter to control level .

@@homemade_audio Thanks, I had to figure out how to get capacitance and inductance values in series, but have it now. JBL Control 1 are about 80hz to 18kHz and they also have an SK3 light bulb as an overload protection and have a 5W 5 ohm resistor which I think I'll replace with an Lpad.

Did you mean 1.2mh instead of 0.2mh?

Sorry datasheed says 4.2khz

Yeah I’m confused about that. It looks good and simple otherwise but for essentially what’s supposed to only be one 2 way speaker should only be a right or left channel which should only require two banana plugs

Also looking for this answer.

Hi Giovanni, most ready made speaker boxes have a single midbass/woofer to handle all the frequencies except for the highs. And they normally have either a 2,2uF or 4,7uF capacitor in series with the tweeter. This is how it is designed and will not sound better any other way. 😎👍🏼

In this speaker enclosure there are 2x 8 inch woofers and 1x 1inch tweeter so the original crossover is not in the enclosure...i want to make a 2 or 3way cross over filter for the speakers so that the bass and high sounds warm and clearly.

Hello, you're right, but you have to read description before. To make crossover there're more important things to keep in mind like TS parameters and distortion/ response diagram. You welcome 🙏

Hello, i have mentioned the values of all components on the video parts section 0min 50s

terima kasih 🥰

🙏

This links for original parts shop : www.hificollective.co.uk/componentshome.html www.banzaimusic.com/Electronics-c-1664/ www.audiophonics.fr/fr/condensateurs-selfs-bobines-hifi-c-6339.html

@@homemade_audio Thankyou

Yes

Can I use potentiometer? N if yes which value

@@MrPstandel No. Lpad doesn't affect the impedance and supports power not like Potentiomètre.

@@homemade_audio will it be okay if i dont have that Lpad

@@salbahebf ok it works, but you have to add resistor in serie instead lpad to control the level of HF response, same for midrange if it's level too high, it depends on the sensitivity of drivers used.

It's better to start with passive crossover if you want to make speakers because it's easy and doesn't cost much money. If you make a mistake in active crossover settings you'll destroy your hf drivers immediately. Don't forget to put 50uf caps between amp and hf driver for safety.

Anda harus terlebih dahulu mengetahui respons terendah dan impedansinya, kualitas suaranya tergantung pada kualitas tweeter dan kualitas kapasitor (sebaiknya mkp).

el montaje es correcto, la señal llega a los extremos del atenuador porque el montaje es un divisor de voltaje (desde -1db hasta el infinito), el otro montaje sin cablear el otro extremo es un montaje en serie a partir del cual la atenuación es de unos decibelios.

todo se nota en el video, ver 0:20min

look at 0:29

Elco size 36 uF 100v

hindi ko naintindihan tanong mo!!

​@@homemade_audio what is the cost of these parts to make the crossover

Thumbnail