20 Tips on a 2-Stroke Top End Rebuild with Phil Valdez
Рет қаралды 26,924
2 жыл бұрынWe took a trip over to the @PrecisionConceptsRacing shop and followed Head Mechanic Phil Valdez's 2003 KX125 to KX144 top end rebuild. Take note of these 20 tips to help you along with your next 2-stroke top end rebuild!
@mikebrown41182 2 жыл бұрын
Eric Sorbys old PC 125 kx. Valdéz have truly kept it in pristine condition 👌🏼
@darioalcala6995 8 күн бұрын
Great video new subscriber
@dirtyburd71 5 ай бұрын
Just reassembled the top end on my 79 husky 250cr. Wiseco piston and rings of course! The engine has been sitting dormant for almost 20 years. Got it back in the frame (replacing the 390cr engine that took it's place years ago) and took 4 kicks and it's alive again! Great video with good advice Thanks!
@walterandrews3077 5 ай бұрын
Always wash cylinder with hot soapy water and lube immediately to prevent flash rusting.
@kirbylee57 Жыл бұрын
Man I dig that music. "I like to put oil all over stuff" too. This video was helpful, but I expected Wiseco to have a little more professional video, like Rocky Mountain's.
@BikerBenny Жыл бұрын
7:33. I dont know if its necessary or not cause the torq is so low but maybe do it in two steps. 5 or 10ft pounds then finishing torq
@criticalthinking3709 6 ай бұрын
The Wiseco piston set I got specifically said it didn’t matter if rings are facing up or down?
@teacherpaco 4 ай бұрын
Does wiseco make a piston for the Suzuki ax100? It’s a 50mmx50mm
@RandomLifeBOXING 10 ай бұрын
Broh.... What about the dots on the chamber... If we make dots with a marking-drill then what's the use of that...
@rufusrunsgsp4610 10 ай бұрын
At about the 4-minute mark you glaze over the surface prep, Im very curious because many use razorblades, some 3m scour pads, and such. But I do not want the gasket to fail. The razor blades leave tiny little scratches which can be a problem. Thank You!
@RwP223 19 күн бұрын
Razorblades on aluminum is safe and effective if you hold the blade vertical to the surface when scraping.
@user-ys1eo2fc9x 8 ай бұрын
What are you living it with
@reallyitzrowe 4 ай бұрын
is the piston ring pre gapped or did you have to gap it with a feeler gauge
@bigguy-ow6rd 4 ай бұрын
sometimes they come pre gapped but its always good to check with feeler gauges
@reallyitzrowe 4 ай бұрын
@@bigguy-ow6rd thanks bro
@joaquinmoreno8151 4 ай бұрын
What are you using to lube the parts?
@bigguy-ow6rd 4 ай бұрын
2 stroke oil
@darioalcala6995 8 күн бұрын
@@bigguy-ow6rd2 stroke transmission oil or 2 stroke premix oil?
@legenderekonwheels 2 ай бұрын
These arent tips. This is instructions on how to reassemble a 144 big bore kit on a kx125
@andya857 2 жыл бұрын
Great video, but, the music sucks..
@wisecopistoninc 2 жыл бұрын
Royalty-free music typically does.
@mikeford5106 4 ай бұрын
SHITTY ... "music" !!!
@pitsterprohill1595 Ай бұрын
Wisco sucks 😕 they sold out
@jimbo7042 Жыл бұрын
Great music but the video sucks
driving 4 answers
Рет қаралды 9 МЛН
Tinman's saws
Рет қаралды 221 М.
Erickson Machine & Performance
Рет қаралды 18 М.
Dirt Bike Channel
Рет қаралды 1,6 МЛН
Ft-share International
Рет қаралды 1,4 МЛН
AUTO VRN
Рет қаралды 3,5 МЛН