End Gap Mistakes That Will RUIN Your Engine

Рет қаралды 375,794

Күн бұрын

Lake Speed Jr visits Jimmy Barton’s Hot Rod Garage to ask the question "how big should the ring end gap be?”
Jimmy shares some some inside tips & tricks from his experience in NASCAR, Drag Racing and setting land speed records on how to set an end gap for the top, second and top oil rail rings without breaking things. Lake and Jimmy share the specifics from both Jimmy's engine and the Engine Performance Expo LS.
For the complete ring gap chart, visit: www.totalseal.com/support-and...
For more about Jimmy Barton, visit / wjesel
For more about the Engine Performance Expo, visit: engineperformanceexpo.com
#enginebuilding #enginefailure #engine

Пікірлер: 549

@masterspin7796 11 ай бұрын

A little loose and nobody knows...a little tight and everybody knows...

@TotalSeal 11 ай бұрын

That’s right!

@dannobee 11 ай бұрын

@@TotalSeal Big ring gap = big catch can. Small ring gap = big trash can.

@TotalSeal 11 ай бұрын

@@dannobee LOL

@wannabecarguy 11 ай бұрын

I've built fixtures and know CTE. Too much end gap won't hurt. People over think this subject.

@MrTheHillfolk 11 ай бұрын

@@dannobee Hah there ya go that's something my ol hs shop teacher woulda said 30yrd ago ✌️ Loose is fast anyway, at least I thought 😁 Staying on the loose side of the spec for valve clearance is what I was told to do,a couple thou of lift lost isn't going to be noticable but your valves will probably be happier in the long run✌️

@jamesjacobs1909 11 ай бұрын

It's the installing mechanic's job to verify the end-gap and not the machine shop's. I rebuilt this guy's engine block and ordered his parts, and he put the engine together himself. He overheated it because the ring gap was not set for a turbo application - he blamed me for not verifying the ring gap before I sold it to him. I told him that, "that's like blaming the gas station clerk for not checking the condoms for holes after you've used 'em." It's the installing mechanic's job to verify the ring gap. Olympia Engine Builders.

@jimthompson6424 11 ай бұрын

It’s the responsibility of the piston installer…always!

@gordowg1wg145 11 ай бұрын

I like that analogy - I must remember it. 😄👍

@kevinkelley3657 11 ай бұрын

I feel your pain. Unfortunately, many of us American men suffer from over confidence AND control issues. Your customer hired you to do the bare minimum, and he was confident enough to do the assembly, not on a street driven 351w, but on a Turbo application. I bet he set the top ring gap at .030 inch for "maximum compression". Roflmao. When I talked to one of theses clowns after a blown engine, I would say: "no warranty on race engines....ABSOLUTELY NO WARRANTY on machine work for race short blocks that I do not assemble to my specs". Tell him he got off for a few thousand dollars for your work, and tell him that assembled race engines start at around $20k.

@DieselRamcharger 9 ай бұрын

lmao. uhhhh....

@dennisrobinson8008 8 ай бұрын

Could cooler burning e85 have made a difference in that situation?

@honkie247 6 ай бұрын

45 years ago I called TRW and asked what ring gap to run for their forged pistons on gas. Their answer was .004 per inch of cylinder bore. Never broke a ring, never scratched a cylinder.

@rafaeltorres2886 6 ай бұрын

I agree TRW was a fantastic forged piston I ran tight gaps on those.

@honkie247 4 ай бұрын

@@rafaeltorres2886 First and foremost, spend the money and use a ring end gap filer. I bought a set of 302 Chevy pistons from them, .030 over with unfinished domes. I managed to run 14.5:1 compression on pump premium gas on the street by using a cam with a lot of overlap. The one thing I had to do was install an ignition kill switch (Joe Hunt magneto) so the engine could spin up to speed before it could light off or I broke the nose off of the starter every time. That car was rough on tires.

@donniebaker5984 15 күн бұрын

That goes for everything since the beginning ,,it's what we would call a rule of thumb ....but today if you are running NOS double the gap on the top ring ..the boys of road kill demonstrated what NOS does to destroy your engine. Without knowing too much about it you can see that NOS would make a lot of heat real quick real fast. And doing so wouldn't make that top compression ring grow very fast and when it touches both ends it rips off the top of your piston ... if you got the air fuel mix exactly right that's the only thing that will go wrong to your engine it makes that top ring grow really quick ... It was proven there during the show with that stock block LS probably out of a pickup truck and they NOS it to death. They did manage to make over 700 horsepower out of a stock 350 horsepower so before.. I think it was the front right side cylinder the ring stuck in the piston no Gap and part of the top of the Piston was gone ..so a quick fix was to double the ring end gap ... But what if you use a total Seal ring set up . And then only on the 2nd ring like they do on diesels ...0.004" per inch of bore x 4" bore = 0.016" + NOS = 0.032" could burn some oil ..but with total Seal rings obviously would burn less ...so what I'm getting at ..who has done this and will you give up the magic numbers for the optimum performancel

@ronflood5697 7 ай бұрын

I have the same beliefs on the three ring gaps, but I try to take into consideration two more things; How much will the rings close up at operating temp? The top closes up much more than the second. You have to anticipate that and adjust accordingly. Also, how much does the ring open up as it seats? A C-33 AP steel ring may not wear the face at all, so it’s gap stays consistent after break in. The second ring, being a tapered face, will open up the gap .00314” per .001” of face wear. per side, which means .00628” more gap, per .001” combined face wear around the ring. That second ring can open up .020” pretty easy. So keep that in mind. This is often the reason people see a power increase “after the rings seat”. It’s not that it’s sealing more compression, it’s that the ring pack starts working better because the second may have been too tight initially. Something else to consider about blow by and gap is, on our drag outboards, some pistons only have one ring, and others have both gaps aligned on a common pin, installed from the top. They still hold 2% leakdown, no problem.

@TotalSeal 7 ай бұрын

Very great points!

@genemounce8302 11 ай бұрын

maaaaaaaaaaaan oh MAN! This is some of THE best ring information I've ever listened to. I have always wondered if there was a gap difference between n20/turbo/alcohol/n/a, etc... Thanks tons, and have a happy 4th !

@TotalSeal 11 ай бұрын

Glad it was helpful!

@Grooty79 11 ай бұрын

I've always run tighter second gaps and had many conversations with guys that did too, never put me wrong and never a blow up from it, BUT I'm building a serious tarmac race car ATM and think I'll pull the bottom end back down and try the larger second ring gap as the rpm is up around 8200 with this motor so it can't hurt to try a bigger second gap, thanks for the good explanation, never too old to learn a new trick 😊

@TotalSeal 11 ай бұрын

Thanks for watching!

@piercer2 10 ай бұрын

I made mine tighter on 2nd as I was told the piston isn’t as hot down there, but by a couple thou

@Grooty79 10 ай бұрын

@@piercer2 I always did the same, I had a conversation with a ring manufacturer years ago that backed up the claim that tighter second gap is better, what I'll do is run it tight on this engine and in 12 months time when it comes out for a freshen up I'll go bigger second gap and try the difference

@ronflood5697 7 ай бұрын

Remember, your tapered face second ring opens up .00628” for every .001” the face wears, easy as Pi.

@billjenkins3699 7 ай бұрын

He's talking about a filled block.. I think the top takes most of the heat and agree with wide if the gap closes.. Never tried or noticed any issue with second or upper oil rail... Interesting discussion

@chazmister56 11 ай бұрын

Glad this video popped up in my feed! Always good to see Lake JR on a video. Great information and tons of good concepts to think about. Gonna be taking a lot of this into consideration when I get the rest of my parts to finish my 410 windsor blower motor and have to set gaps.

@TotalSeal 11 ай бұрын

Glad you enjoyed it!

@edsmachine93 11 ай бұрын

Good information. Thanks guys. I have been opening up my second gap for a few years now. Thanks for sharing. Take care, Ed.

@TotalSeal 11 ай бұрын

👍👍

@syrthdr09sybr34 11 ай бұрын

This video clears out so many doubts, wish it had been around when I was building my motor. Would be interested to see you guys discuss piston to wall clearance.

@TotalSeal 11 ай бұрын

We are glad it was helpful!

@HiTechDiver 4 ай бұрын

I really like Jimmy; what a personable and knowledgeable guy. He's the kind of guy I would enjoy sitting down and having a conversation with.

@TotalSeal 4 ай бұрын

He’s awesome!

@scottcooper1173 11 ай бұрын

I debated myself for weeks on what to do for end gap on a 225 V-6 Dauntless Jeep Engine. Cost of boring and line honing in my area is not cheap, plus the fact many machine shops have closed down over the years, also could not get .020 rings due to several factors , they weren't available. The Cylinders measured out just over 3.75 to 3.77 throughout each. So I honed them myself and ordered standard rings and installed with 28-32 gaps....Sure that's a lot....but these little Odd-Fire engines run pretty warm too.......still waiting for the heads to get finished 4 months at another machine shop. It's become impossible to rebuild motors fast anymore.

@broke_dongle 11 ай бұрын

Done that and no problems using PCV or switching to pan evac system for oil control blowby.

@MrFantasylover1 8 ай бұрын

Thank you sir. Your expertise is ao great to hear. Ill follow this on my next build. I love that you are so humble for a man whose been 277mph at Bonneville!! God bless! you!!!

@TotalSeal 8 ай бұрын

Jimmy is the man!

@luislam6259 10 ай бұрын

Guy's, thank you so much! This was a huge help and it saved me time and money. God bless you both!

@TotalSeal 10 ай бұрын

Glad it helped!

@CS_247 11 ай бұрын

Been building normally aspirated gas race engines for 20 years, and ALWAYS go a little bigger than the Total seal chart. Never had an engine butt a ring, and i leakdown the cylinders after every race, the blowby is minimal. "A little loose and she"ll still go, a little tight, and it'll be a bad night..".

@TotalSeal 11 ай бұрын

Absolutely!

@motersickel 5 ай бұрын

This is making me feel better..I'm building a Honda engine for a guy It's a d series... I tried to offer him a better engine but he wanted to stay factory and just build it... So, we had custom wiseco pistons made for this engine 75.5 mm bore, stroke is .163 mm longer than factory rods...when I was checking the ring gaps they were a little bigger than what was specified on the sheet from wiseco...there was three different end gaps... street ,street /strip, nitrous /boost... Well the gap is slightly larger than the nitrous boost gap setting but this engine is going from 9-1 compression all the way to 11: 00-1...The bore is exactly on par and the Pistons measure exactly on par with the correct clearance.. My machine shop guy says it'll be just fine... I think it was like 26ths... The biggest setting on the sheet was 24... I think it's about 2 to 3,000s More than the biggest measurement... This engine will never see a turbo but there's a possibility he might put a 50 shot on it at some point so I guess the slightly larger ring gap is okay....

@supersevenn 11 ай бұрын

great to hear from Lake Speed Jr again !

@martinlang9615 11 ай бұрын

Thank you for including high performance diesels in this discussion. It makes a lot of sense

@TotalSeal 11 ай бұрын

We are glad it was helpful.

@ronniewilliz153 11 ай бұрын

I learned a lot.... it makes total sense. I'll stick to modding rc engines for now tho.

@shoominati23 11 ай бұрын

It's amazing how if you take the oil scraper rings and bend the ends so they point back towards the piston skirt instead of having that /\ outwards, the pistons just glide in the bores instead of needing to be tugged on. And this was $0 mod was worth over 20hp on my friends car, LOVE things like that and thats what the name of the game is here!

@fastinradfordable 11 ай бұрын

I’ll do this next time!

@matthewuhrich6439 11 ай бұрын

Better run a good vacuum pump

@davidreed6070 11 ай бұрын

I'm concerned about losing oil seal. I am thinking of trying it but I drive a lot on the street

@alro2434 11 ай бұрын

Bend?? How'bout just radius the corner?

@63turbo 10 ай бұрын

@@alro2434 I actually tried that on the top and second ring, even though this is supposed to be an absolute NO NO and there has been no huge problems with it. It was kind of remarkable as to how low the oil consumption was as compared to the previous engines that I've done. Boosted air cooled engine, daily driven.

@dschefers9700 5 ай бұрын

One of the best short building videos I’ve watched!

@TotalSeal 5 ай бұрын

Thanks!

@jt.124 6 ай бұрын

Man such a wealth of knowledge. I messed up and did a gapless top ring on my turbo rb25 and until it gets hot at the track it smokes a decent amount. I’m not pulling any vacuum on my catch can and it seems like that could be my main issue w using these rings. That or I never seated them properly lol. Great vid!

@TotalSeal 6 ай бұрын

Thanks!

@johnelliott7375 6 ай бұрын

As long as you lead the race or being in second 🥈 will ingest less dirt than anywhere else on the track. Bravo 👌👏 on that one Lake and Mr. Barton. Thanks again for sharing this with us Mr. Speed Jr!

@TotalSeal 6 ай бұрын

Thanks!

@RonaldLewis-py6yt 5 ай бұрын

Great information I had to watch a couple times ,built many engines and always went by the charts looks like it's time to widen the Gap, Thanks for sharing!

@TotalSeal 5 ай бұрын

Glad it was helpful!

@donjohnston4215 9 ай бұрын

I bought a set of Keith black silvalite hypereutetic pistons shortly after they came out. Probly late 90s. Installed with the gap set per instruction sheet that came with pistons. Ran great till I made my first extended WOT pass in high gear. Broke at the ring land on 4 pistons. Turns out the instructions were not correct in the very first pistons they sold. I always go on the side of caution now. A little extra gap is not terrible.

@TotalSeal 9 ай бұрын

Thanks for sharing.

@ronniecox109 7 ай бұрын

.004 per inch of bore, for a stock engine, .005 forlow boost,.006 for hugh boost. And those pistons are junk. Broke lands on 4 seperate occasions with the hyper.pistons , in one season. Put a set of forged in it, and ran for 3 seasons. No problem. The hyper. Pistons were made in Bangladesh.

@PietStemmet 5 ай бұрын

I learnt that as well way back

@TonysHotRodGarage 11 ай бұрын

Great discussion guys! Thanks for this!

@TotalSeal 11 ай бұрын

Glad you enjoyed it!

@clemzahrobsky2137 11 ай бұрын

i saw a test at GM tech center on a 700 HP NASCAR cup engine where they opened the ring end gap to .125 and the engine lost less than 5 HP. lots of blowby but little HP loss

@davidleary823 11 ай бұрын

Yes. Keith black put out an article about 30 years ago where they increased gap all the way to ,060 before it changed hp and blowby. I can’t find the old article but I remember it so well. They also ran huge second gaps and made more power.

@keithtobin5369 9 ай бұрын

Thanks for all the high tech info.

@bryang9158 7 ай бұрын

High rpm eng not enough time to leak at high rpm

@Fordcertian 6 ай бұрын

I've watched some of your videos and you use this great pistons, never revealing what kind or who makes them. What kind are they?? Went to total seal web site, no pistons!

@bassettraceengines 11 ай бұрын

Great job Jimmy !!!!

@user-bg6fy2rn1c 11 ай бұрын

Great video! If I may ask your thoughts on this setup? Maybe I will get lucky. Will be finishing up my gapping soon. 468bbc/13.5-1static compression/ Total seal Gapless rings/ wet sump/ internal balance/ Blown alcohol/ wet block/flatbottomdragboat/ 32 gears/ 11 1/8" x 16 -2 blade prop. Interesting about the top oil ring gap trick. Thanks.

@TotalSeal 11 ай бұрын

Thanks for the watching and the comment, you don't need to do the oil ring trick with a Gapless ring package.

@darenwinckler7027 6 ай бұрын

I am glad i watched this. I just learned so much about the science behind rings & gaps.

@TotalSeal 6 ай бұрын

Thanks!

@Fmandan77 Ай бұрын

This is very interesting. I've never heard that a 2nd ring's gap should be greater than the top ring...very interesting explanation.

@TotalSeal Ай бұрын

Glad it was helpful!

@jerryfarmer5989 7 ай бұрын

I have a mopar 360 I built. Only bored .020 and went back with stock cast iron jugs, not a hot rod. The rings I got are posi loc's. I tore the engine down with about 1k miles on it. The white coating on the bearings was still there and the cylinders set in perfect. In my opinion make sure the machine shop knows what your going to be doing.

@johnboomer8468 3 ай бұрын

thanks for sharing your expertise

@TotalSeal 3 ай бұрын

My pleasure!

@alanhawkins4841 11 ай бұрын

I build single cylinder air cooled race engines some have an cast iron blocks some are iron sleeved aluminum blocks and I have found that there is major power increase for the proper end gap for the top two rings. the second ring is not a compression ring, it is an oil control ring only. If the top ring doesn't seal none of the other rings are going to do that job, oil control is their job. The pressure differential between the combustion chamber and crank case is what seals the top ring to the cylinder and crankcase. If the second ring sealed combustion pressure the top ring would not function at all.

@TotalSeal 11 ай бұрын

Absolutely!

@kregchapman6981 6 ай бұрын

Great video, thank you for sharing..

@TotalSeal 6 ай бұрын

Thanks for watching!

@tracylewisperformance2270 22 күн бұрын

Always good info! Would you be willing to test a patented system that corrects the raw fuel oil dilution issue on GDI Engines?

@truspirit1925 5 ай бұрын

Great info guys thanks

@TotalSeal 5 ай бұрын

Any time!

@joe-hp4nk 5 ай бұрын

I learned the strength of a forged piston from a engine I bought and he said the pistons were forged. A while later I lost all compression in #7 cylinder. When I took it apart the piston ring lands were broken and it was a cast piston. All the other pistons were forged and were fine.

@TotalSeal 5 ай бұрын

Thanks for sharing!

@zAvAvAz 11 ай бұрын

Hey youns! this was totally fun thanks a ton.

@TotalSeal 11 ай бұрын

Glad you enjoyed it!

@canadiantechprep 4 ай бұрын

Whelp, looks like I'm opening the engine up again on this bike. Thanks for the details on the "why?". "1/8 (.125) of an inch, or 125/1000s" clarified it for me...more is fine for that second ring.

@TotalSeal 4 ай бұрын

Glad to help

@johnelliott7375 6 ай бұрын

Nothing like a honest man, I think 🤔 I will now investigate now if I can't or don't get a answer from now on.

@bobirving6052 11 ай бұрын

Great stuff guys!

@TotalSeal 11 ай бұрын

Thanks so much!

@harleylif1929 7 ай бұрын

Good morning gentlemen. I have learned a lot of new things watching your videos and have put it to use on my engines with great success. Now I have a question about the piston ring to ring land clearance . I understand to tight will weld or lock piston ring to the piston but what happens if we make the clearance more. Book specs says .0005 to .0025. Would we notice anything if we set it to the higher clearance? Thank you for your time. You two are the best.

@TotalSeal 7 ай бұрын

Thanks! That is a great question. Too much vertical clearance is bad. It lets the rings flutter around. For no gas ported pistons, .0015 clearance is good. For gas ported rings or pistons, .001 (or tighter) is good.

@sweet65mustang Ай бұрын

I know guys that run demolition derbys and they often open up an engine and file the rings a bunch. They're a little hard to start but they will run a derby with no coolant and use the engine for years

@TotalSeal Ай бұрын

Thanks for sharing! That’s a great (yet extreme) example.

@baims8367 11 ай бұрын

Let the man talk your interviewing there Mr SMARTY PANTS! 👖

@boomersuperbike3787 11 ай бұрын

wow if JR would just let these guys talk instead of interrupting his interviews

@bobirving6052 11 ай бұрын

I thought it was not a bad back and forth. Both men are very worth listening to.

@gsxrsquid 8 ай бұрын

Best explanation I have ever heard.

@TotalSeal 8 ай бұрын

Thanks!

@user-Dr. 7 ай бұрын

In all the instructions I have ever had that comes with the rings including Total Seal has me setting the top ring end gap wider than the second, just put a new engine together, wish I had seen this sooner, I guess things change as we learn more.

@TotalSeal 7 ай бұрын

The instruction sheet recommendations are very safe. This is just cutting edge tech tips.

@dennispage5333 11 ай бұрын

Lake Love the work you do. Damn I wish you were around 30 years ago.

@TotalSeal 11 ай бұрын

Thanks!

@wallebo 29 күн бұрын

What a great video! Kudos, kind sirs.

@TotalSeal 29 күн бұрын

Glad you liked it!

@wallebo 29 күн бұрын

@@TotalSeal I loved the vast years of experience distilled into one succinct video that was all killer and no filler!

@jcnpresser 25 күн бұрын

I’ve watched guys build engine and always j just throw the oil rings in and don’t even check them, ah they don’t matter. Nice to know exactly how important they are to be gapped, at least the top rail.

@TotalSeal 25 күн бұрын

That’s why we make these videos!

@mitchc3569 6 ай бұрын

I thought that a “little loose” was just common knowledge. Thanks for this guys.

@TotalSeal 6 ай бұрын

Happy to help!

@devinalleman 11 ай бұрын

Keep this stuff coming!!!!!!!!!!!!!!

@TotalSeal 11 ай бұрын

Thanks!

@Hitman-ds1ei 11 ай бұрын

Great info on a great topic 👍

@TotalSeal 11 ай бұрын

Glad you think so!

@PaulOffordRacing 7 ай бұрын

Excellent video!

@TotalSeal 7 ай бұрын

Thank you very much!

@99bevo 17 күн бұрын

A good explanation. I seen engine's with to little of end gaping suffer from cold engine seizure . Cold seizure....? End gapping being tight added with over revving of a cold engine before it has reached the optimal temperature for the cylinder bore to expand .... The end result is like he says an expensive day at the office .

@confuse9 11 ай бұрын

In Jenkin's book (mostly talking about his old small block pro-stock engines) he talked about running a tighter end gap because he had a straighter bore (honed with torque plates). if you believe this, what do you do with newer honing machines like Rottler (sp?)

@TotalSeal 11 ай бұрын

End gap is more about combustion temperature than honing technique.

@DesertRatFabrication Ай бұрын

Keep em coming Dennis 😀😀

@TotalSeal Ай бұрын

Will do!!

@stevelee5724 6 ай бұрын

Lake is such a cool guy! Cheers from New Zealand 🇳🇿

@TotalSeal 6 ай бұрын

Thanks!

@T500cal 3 ай бұрын

Such good information! Your view to subscription ratio is almost criminal!

@TotalSeal 3 ай бұрын

Thanks!

@mavcar38 10 ай бұрын

Awesome info!

@TotalSeal 10 ай бұрын

Thanks!

@user-ld3om3on4t 6 ай бұрын

I've got your advice to open the upper oil ring to match the 2nd ring on a 3 piece oil ring. What about on a 2 piece oil ring that has only one gap. Mahle just says .015 or bigger but the second ring is .023 in this Porsche turbo engine. Thanks very much for the great videos!

@TotalSeal 6 ай бұрын

Thanks for the question. For a two piece oil ring, just go with the .015 minimum gap.

@notchback93 5 ай бұрын

Any suggestions on gap for A Cummins 12 valve running some high boost around 60 psi thru compound turbos, any advise would be appreciated thanks for the video

@McadMcad Ай бұрын

I opened the hood. I checked the oil, and sprayed some belt dressing on the belt. That's as far as I got. The pistons, are underneath a bunch of stuff.

@TotalSeal Ай бұрын

LOL, they are quite inconvenient to reach.

@JG-kv4oi 15 күн бұрын

Just screw out the spark plugs, you can get right to them. This is a secret professional mechanics don't want you to know!

@cda28rboostingpower27 Ай бұрын

Congratulations on the video, very good information. I have a doubt, it is always said that the oil ring must have a minimum of .015" but if we try to equate the gap of the oil top ring to the 2nd ring, this would be much further away than the minimum (.015"), so when or how much would be too much gap for the oil ring?

@TotalSeal Ай бұрын

Only the bottom oil rail needs to be .015 or larger (up to .025 for this set up), then add the extra gap to the top rail.

@Cobra427Veight 11 ай бұрын

Hey guys good video , I bought a old Matchless G80 500 , there's a short video on my channel , anyway it was semi restored but didn't make to the road , I got it running ok, but big oil leaks , so removed the head and was astounded to see piston ½ down the bore at TDC ? Wrong piston , and I found all 3 cast rings with .125" ring gap, it ran ok and pulled ok , calculated comp 4.1:1 . Cheers .

@jiyushugi1085 11 ай бұрын

Maybe wrong rod. When I was flipping bikes as a kid a Yamaha 2-twin I was working on had a bad rod. Bought one at a Yam shop, checked the small/big end sizes and slapped it together. turning the engine over on the bench with the heads off and.....oh F, the piston attached to the new rod didn't come up as far as the other one. Bike still ran okay, so out the door it went.

@eweunkettles8207 7 ай бұрын

more likley a 500 top end on a 350 crank

@Cobra427Veight 7 ай бұрын

@eweunkettles8207 definitely G80 on the crankcase , there were different pistons for different conrods , I bought a new piston, all good .

@eweunkettles8207 7 ай бұрын

@@Cobra427Veight some had a wire wound piston have you seen one? my friend had a g80cs made a long stroke pressed up Ina needle roller crank and titanium rod with a vincent piston gave 700 cm3 the cs had a centre plug that fired thru a slot between the valves supposedly to stop wetting the plug when starting the motor it went very well but got a bit hot in city traffic the rickman bros raced a similar motor in mx in one of there metisse frames . more recently a big bore short stroke matchy g80won a race beating manx nortons and vincent twins at the goodwood festival of speed so the humble matchy can be a helluva performer the weak bit is the timing side bearing

@brettyh1 5 ай бұрын

great information in these videos

@TotalSeal 5 ай бұрын

Glad you like them!

@jeffsnider3588 18 күн бұрын

The famous philosopher John Locke - All knowledge comes from experience...........So true!

@kdsowen2882 6 ай бұрын

Very -informative , Thanks again . Dave nz

@TotalSeal 6 ай бұрын

Glad you enjoyed it

@crawford323 7 ай бұрын

Spartan Aviation in their aircraft and power-plant mechanics course built a Lycoming engine properly then disassembled the engine and rebuilt it several times increasing the ring gap each time. They measured the hp each time with lower and lower compression and found little difference other than oil consumption and blow by. I was certainly surprised by this test. It is easy on an air cooled aircraft engine to access the pistons without removing the rod bearings. The cylinders come away from the pistons. So they were curious and did it. On an engine stand of course.

@TotalSeal 7 ай бұрын

Thanks for sharing!

@malbirrell 10 ай бұрын

Rebuilt a 2 stroke mx bike engine for about the 5th time. It kept seizing the piston in the bore. This time i ran the ring gaps at factory max. So far no blow up...

@vehdynam 7 ай бұрын

Very good video. can yo explain what to do with the expander . Gap , no gap ,etc. Thanks.

@TotalSeal 7 ай бұрын

Leave the expander alone. You can adjust the end gap on the oil ring rails.

@chrisobrien9334 11 ай бұрын

Thanks this is great information.

@TotalSeal 11 ай бұрын

Glad it was helpful!

@chrisobrien9334 11 ай бұрын

@@TotalSeal I’m building my LS Turbo 6.0 and gathering as much information on everything before I start assembly.

@LoydChampion 5 ай бұрын

In the way back machine I did a chart for ring end gaps based upon what the engine was doing and what its induction of it is. It is based on the multiplier in thousands of an inch of ring thickness X cylinder bore X projected torque peak RPM. Different numbers are used for different materials of the ring and the piston materials. As he said, some of the guys that worked for me over the years ended up going to other engine shops and used this formula guide. I had a couple of them call me to tell me how messed up I was that are very well known engine people of their time. Fast forward, I had one of their engines found there way to me and I had to laugh when I took it apart about found the ring gaps exactly where I would have set them based on my chart. About a year later I was at this persons shop in North Carolina and gave him some crap about it and he laughed... Pulled out my chart from his desk and asked if I had ever seen it before.... One of my guys moved back there and had gone to work for him and he gave it to him, they have used this guide ever since. Funny of what goes around and comes around in this business.

@matthewuhrich6439 11 ай бұрын

I think its funny that we have been doing that for a long time even though ring manufactures said we should be doing the opposite.

@victoramato4692 5 ай бұрын

What about a regular street engine? The biggest thing a machine shop customer complains about is oil burning. Most ring sets, ex. Sealed power, Hastings, are engineered sets. And gaps are pre set. Usually 3.5 to .004 per inch of bore. Never had a problem. Chrome top rings are hard to break in because most people drive their "new" engines too gently. They need hard acceleration to "scrub" them in. Don't let new engines idle! Worst thing! Just drive it!

@harrisonclark4382 2 ай бұрын

Question, I have a built, sleeved Coyote with a blower, and I mistakenly ran some 5W-30 oil. I noticed that my car smelled like fuel and so did my oil. Ran the piss out of the car too. The smell of E85 went away went I but the proper oil 5w50 in. I’m wondering how much damage if any I did to the motor? Seems to run fine though.

@richardsmith-qy6vl 11 ай бұрын

Very good information I was told 5 thousands for every inch of bore on a n/a combo is safe . I'd love to build a turbo engine but I don't know anything at all about them.

@TotalSeal 11 ай бұрын

Yes, that’s a safe bet for a NA engine.

@bobirving6052 11 ай бұрын

George Bryce says .04 per inch for NA and .07 per inch blown.

@chrisjarvis4449 11 ай бұрын

stock set up i go with pi per inch of bore or .004 per inch of bore

@christianwise4403 4 ай бұрын

All depends on combustion chamber temp which is affected by fuel used. Rich or lean mix, power added, etc. Old rule thumb was .004” gap per inch of bore on street car gasoline. Going slightly bigger doesn’t usually hurt. Remember to offset ring gap locations on your pistons upon install. Plus good ring quality or mfg for seal in cylinder along with a good cylinder finish hatch pattern to match the style or material of the rings. With a straight cylinder bore. Tapper or out of round cylinder also affects ring seal. Do a quick dinkle ball hone and new rings and bearings might be cheaper but at times won’t help ring seal once cylinder worn badly. Measure twice cut once remember lol

@turbotrana 18 күн бұрын

I have an old set of total seal gapless ring set where the gapless ring was on the second ring and the ring gap recomendation is wider on the top than the bottom. I trust the latest tech but just goes to show it takes a while to work out what is best. I never used that ring set as I heard guys complaining of ring flutter and oil burning back then.

@ForceEngineering 11 ай бұрын

is static gap (set on a stand) very representative of ring gap at operating temp? the top ring surely sees more heat, and the the top and second ring are almost always different martials and different coatings. These differences surely affect the amount of (growth) the ring has which changes the gap during load. I could see some scenarios where gapping the top and 2nd rings the same on a stand, would result in the the top gap being tighter during operation.

@TotalSeal 11 ай бұрын

As you mentioned, static gap is not what the operating gaps will be. The top ring gap will close up more than the 2nd ring due to the heat.

@Brandon74Johnson Ай бұрын

I’m building my own motor for the first time for a dirt modified just a 350 bored over 030 and I’m just curious what you think ring gaps should be on that?

@michaelshay5594 6 ай бұрын

Good info. 👍👍👍👍

@TotalSeal 6 ай бұрын

Glad it was helpful!

@andrekemp5059 11 ай бұрын

Great advice

@TotalSeal 11 ай бұрын

Thanks!

@jarheaded9278 20 күн бұрын

If I were to run an older forged piston that has 12 thousands loose in bore on a sbc..what would I need for rings, std or 5 thousands larger than std. also, what would be the ring gap size. Thanks.

@OVTEC91 Ай бұрын

Interested in the science behind opening the top oil gap to match the second ring.

@Op1zilla 9 ай бұрын

Great info 👽👍

@TotalSeal 9 ай бұрын

Glad you think so!

@STEAMSHOVEL65 19 күн бұрын

I've got a 400m ford its bored .030 over, the rings out of the box are .026, actually a tight .027 they are hasting's moly rings, piston are silvolite hypereutic, going by the ring gap chart they should be .019 to .020. any help would be great

@jimmungai1938 11 ай бұрын

This is six in a row jim again how about Charles and Albert zero gab second ring set that’s a real interesting piece

@arthurrodesiler3109 Ай бұрын

My as well give you secrets away rather than die with them. Your Knowledge will always help someone save money from big mistakes. I always did. I drag raced so it we et the car so helping someone was no big deal. Years ago GM said up to .060 ring gap they seen no lose in power just a little more blowby. Past .060 they saw power lost.

@TotalSeal Ай бұрын

Thanks!

@rijk1857 11 ай бұрын

The young guy....Let the man talk

@AK-DIRECT907 22 күн бұрын

I'm more of a road/rallye guy. I'm always looking to build for endurance. I racked up 40.000miles on my POV. What kind of ring gaps do you run on a vehicle running 18 to 20 hrs for 7 days (gas) ?

@MitzvosGolem1 2 ай бұрын

Diesel a different story . Must be perfect to spec . Or hard cold start. A little loose on gas is ok. .004 to .006 per inch diameter of bore is normal. Also gaps rotate around cylinder in time randomly eventually. Excellent channel 👍

@TotalSeal 2 ай бұрын

Great point!

@automan1223 2 ай бұрын

Jimmy has forgotten more than most of us will ever know....

@TotalSeal 2 ай бұрын

Absolutely

@Shattered_Instance 10 ай бұрын

Lol, speaking of Turbo Diesels. My highly modified engine decided it was time to spit the Transfer case out, quite literally. Only thing that kept it somewhat in place was being connected to the driveshaft.... You could see daylight through it lmao. Good excuse to mode the drivetrain to match the engine I suppose.

@cfmechanic 2 ай бұрын

Well this has me 2nd guessing our choice of a Napier gapless 2nd ring. Although I have almost no blowby out the valve covers I am seeing puffs of smoke out the pipes at full throttle, ring flutter? Sbc 440 dart. Started at 427 and grew as I learned. Daily driven sniper efi and handles road trips just fill gas and check and add oil and it will go anywhere fast.

@Fk8td 26 күн бұрын

I do .0050 per inch of bore in a stock to mild street car. Turbo I do .0060 per inch and turbo with nitrous or nitrous .0070 per inch of bore. He’s over .0080 per inch of bore but this depends on temps. I usually add at least .0005 more to the second ring. I get NOTHING in my catch cans and usually that comes down to did you clean the cylinder walls properly and get all of the stone from honing out. Jet wash will NOT clean stone out. Use transmission fluid and shop towels on the walls till you see no black coming off of the rag.

@TotalSeal 26 күн бұрын

Right on!

@justinpakarno4346 6 ай бұрын

Jimmy is a treasure.

@TotalSeal 6 ай бұрын

Absolutely!

@albertkinney8021 8 ай бұрын

Always do the bore per the piston makers specs I have never got a set of rings for the correct bore that were near factory specs . Threw trial and error I just run the rings that come in the box . haven't had a motor blow up yet .Any imput on ring gap on a air cooled motor ?

@TotalSeal 8 ай бұрын

The air cooled engines can run a tighter gap because the cylinders expand more.

@pingpong9656 6 күн бұрын

Is it normal for new piston rings to make a slight scraping noise and be a tiny bit rough in travel on a new install while rotating crank by hand? I can turn crank easily but it's very strange to hear the noise - I;m thinking it could be the new rings just riding on the new deglazed walls making the noise... Please tell me this is normal!

@geriatricprogrammer4364 6 ай бұрын

Here in the UK, it's 10% ethanol. My car was built before the ethanol blends, if 10% burns cooler than 100% petrol then is that why I burn a wee bit of oil?