200 TDi Injector Cleaning.

Рет қаралды 175,705

Fluffle Valve Express

7 жыл бұрын

I created this video with the KZfaq Video Editor ( / editor )

Пікірлер: 64

@johnkerr8019 5 жыл бұрын

I've watched quite a few of these injector cleaning videos and this has been the best so far, very comprehensive and great to witness the end result. Good JOB!!

@FluffleValveExpress 4 жыл бұрын

Thanks ...

@gerryrichards2863 5 жыл бұрын

Thanks mate. I have my injectors out on my 98 Land Rover Discovery 300 TDI and will follow your instructions to clean them up and see how it runs. We are in Winter here (Australia) and I hope the cleaning will make it run a lot smoother for the Summer months when I use it the most. It runs quite rough at the moment. Great instructions mate. Thank you - Gerry

@FluffleValveExpress 5 жыл бұрын

How did it go with the clean up?

@piecetoyou8285 2 жыл бұрын

Nice work thank you, A little tip for you, when placing litlle washers down any tube` if you get a long wooden skua place that down into the injector` and then place washer over skua ` the washer will drop down without flipping then just remove skua,

@colinaglae9753 3 жыл бұрын

Super video, Fluffle. Extremely educational diesel injector cleaning video !!

@FluffleValveExpress 3 жыл бұрын

Thank you.

@jamesferguson1140 3 жыл бұрын

Great info. Thank you. I will have a go at my marine engines now after your teaching. Thanks again.

@IQ0100 6 жыл бұрын

Cheers mate. Will have a go with my Pug 407 2.0 hdi injectors. Ys jazz

@johncraig6986 5 жыл бұрын

excellent strip and reassembly, and advice; really useful.

@TheBert1948 6 жыл бұрын

thanks for the video, helped me cleqn the injectors on my car, saved £480,

@FluffleValveExpress 5 жыл бұрын

What car is it?

@Red_Vector 6 жыл бұрын

Thanks for the video very helpful and easy to follow

@di4241 3 жыл бұрын

Very educational, thanks for making this video.

@johnswimcat 6 жыл бұрын

Great video. I would wear nitrile gloves though and would use copper wire to unclog the nozzle holes... unless I was desperate..!! I wouldn't use a sewing needle though unless I was completely desperate... as anyone who works on their own vehicles will sometimes be!

@MarktheOddJob 6 жыл бұрын

Nice video Frenchie, never knew you were so famous!

@davidwall6020 2 жыл бұрын

great video ...makes me confident to try it myself, Thank you

@jameslatimer1432 5 жыл бұрын

Great job bro got to do my m57 ENGINE BMW 3.0td x6 same job

@TheYesnoyesnoyesno 7 жыл бұрын

Very useful - thanks!

@charlescopp3432 Жыл бұрын

Thanks from up state NY 🙂

@FluffleValveExpress Жыл бұрын

Thank you 😊

@charlescopp3432 Жыл бұрын

Thanks 😊 great tutorial!

@DavySwift 4 жыл бұрын

Nice one 👍 Thanks for sharing.

@AnasKhan-vz6gn 6 жыл бұрын

Thank

@albertoromano7853 Жыл бұрын

Ciao, complimenti hai fatto un bel lavoro e un bel video.

@FluffleValveExpress Жыл бұрын

Thank You.

@javerlozep162 3 жыл бұрын

Great video never seen

@FluffleValveExpress 3 жыл бұрын

Glad you enjoyed it

@stanislas2008 5 жыл бұрын

Fucking master .. you're a great help.. thank you so much for your expertise and patience to do this awesome videos...

@nazmibullari6469 5 жыл бұрын

Bravo

@jeffmee763 5 жыл бұрын

Hi Isi it a a bosch injector thanks good video.

@FluffleValveExpress 5 жыл бұрын

I do believe it is a Bosch Fuel injector.

@markrayton6385 3 жыл бұрын

Excellent video. Thanks for sharing. Only problem I have is I don't have access to an airline.

@FluffleValveExpress 3 жыл бұрын

That'll be the next thing on your shopping list. An Air-Line is a godsend in any workshop.

@peterbloggs8750 5 жыл бұрын

Excellent video but why not anneal the copper washers before you put them back under the injectors?

@FluffleValveExpress 5 жыл бұрын

This something people don't know. I have in the past annealed copper washers on sump plugs. I suppose it depends on "If it leaks" or not. Sometimes it's just as well the buy new.

@mauricioericfalcon9546 2 жыл бұрын

Lo intentaré 👍🏼

@eyeswideshut7732 Жыл бұрын

time stamp 30.22 lol what happened to cranking for 20 mins.... if only they were all like that...

@ciaranoconnor6783 2 жыл бұрын

Hi' I have just had an engine fitted on my 313 sprinter. Mechanic has fitted new delphi injectors but wont start. Delphi say injectors have been scarred and are now knackered (won't replace them) have you or your followers experienced this , what could be the cause and do you know of a solution

@FluffleValveExpress 2 жыл бұрын

Could be the mechanic has damaged them somehow? If you damage the Nozzle/Tip of the injector, it won't spray correctly.

@ribama1 2 жыл бұрын

This is a great video but you need to know what type of injector you have. If you have a piezoelectric injector it is hydraulic no springs and tolerances of 3/1000th you can't clean like this.

@jasonga Жыл бұрын

What do you put on them to aid removal in the future?? Please…

@FluffleValveExpress Жыл бұрын

Copper slip on the threads.

@jasonga Жыл бұрын

@@FluffleValveExpress YES, I knew it, I been doing that and work mates cocking nose up…. I use the copper slip and really rub it in……. Thanks, good video…..

@RoyaJoha 3 жыл бұрын

I did the work!.. deleted code and yay!.. Except 8 sec later code is back and now it’s leaking at new areas.. any torque spec on the items (all pref) for a Ford transit connect? 😅

@FluffleValveExpress 3 жыл бұрын

Sorry, I know nothing about the Ford Transit other than that I owned one in the late 1980's It was a MK2 Mini bus, converted to a camper.

@RoyaJoha 3 жыл бұрын

@@FluffleValveExpress ah that’s all good 😊 thank you for the video though! I’ll get there in the end I’m sure.. orrrr a new injector is already in the mail..😅

@BillSikes. 5 жыл бұрын

I tried this with my mondeo tdci injectors and its never run since, I don't think they're opening, it won't fire at all

@FluffleValveExpress 5 жыл бұрын

Hopefully, you have put them back together in the correct order that they came apart? Also, did you bleed and prime the diesel system before trying to start the engine?

@BillSikes. 5 жыл бұрын

@@FluffleValveExpress Thanks for the reply, yeah it's all bled up, and there's pressure there, coz I get a big squirt when I crack the nut on the inlet pipes, but il dismantle them again tomorrow to see if I didn't put them back right, cheers il let you know

@TVTika 2 жыл бұрын

@@BillSikes. what news ?

@BillSikes. 2 жыл бұрын

@@TVTika It never ran again, I scrapped it in the end

@habibizhafranzhafran8343 3 жыл бұрын

May Allah give you hidayah....aamiin

@Stainless316L 2 жыл бұрын

brake cleaner/tattoo remover lol 😆

@xXJusTMichelxX 2 жыл бұрын

I took an injector off to clean it and now the car is not starting, all the injectors are not spraying, there is pressure in the rail but the injectors are not opening. Help me please

@FluffleValveExpress 2 жыл бұрын

Try bleeding the system. Crack open the feed pipe to the injector while cranking the engine over. Are you sure everything went back together correctly 🤔.?

@xXJusTMichelxX 2 жыл бұрын

@@FluffleValveExpress Was air in the rail, I did what you said and it starting now . I can't thank you enough. Have a great life. Can I give you £10?

@FluffleValveExpress 2 жыл бұрын

@@xXJusTMichelxX I'm just glad that you are sorted 👍 😊 Keep your moneys for fuel ⛽

@xXJusTMichelxX 2 жыл бұрын

@@FluffleValveExpress Thank you again, sorry didn't mean to be rude about the money, If you were here I would probably take you out for a beer :))) ! Have a nice day!