Backyard Mechanic procedure to change Cam Seals utilizing a home made cam seal install tool on a Mitsubishi Eclipse GT V6 3.0L.
Пікірлер: 27
@nitrous07me3 жыл бұрын
Thanks for making this video
@johndodson89656 жыл бұрын
thnx for the video
@hazegrayandunderway80776 жыл бұрын
John Dodson you're welcome. Alot of info...hope it helped
@24BLUEELMO6 жыл бұрын
Hello i was duing this but I pushed the seal to far in . do I take it out again or would it be ok?
@Paulieh0735 жыл бұрын
Thanks for the video... Question... I think I have the same problem on my 3.0.Did you need to undo the engine and jack it up some how ? Thanks...
@hazegrayandunderway80775 жыл бұрын
Yes, before you disconnect the motor mount, put a floor jack under the oil pan to support the engine. Just make sure you put a piece of plywood or similar to protect the oil pan from the jack
@Paulieh0735 жыл бұрын
@@hazegrayandunderway8077 thank you...
@mrplumrite85795 жыл бұрын
Same thing happened to me aaaaah!
@drewdowncutomz47925 жыл бұрын
So how did u remove the seal??
@RPMzRUDY3 жыл бұрын
I was wondering if you have to remove the intake manifold at any point while replacing seals?
@hazegrayandunderway80773 жыл бұрын
No you do not, just timing cover, belts, cam gear, etc
@RPMzRUDY3 жыл бұрын
@@hazegrayandunderway8077 thank you so much for making this video made my day a whole lot easier. Finally finished wife's car. Happy wife, Happy life.
@hazegrayandunderway80773 жыл бұрын
@@RPMzRUDY good job man. LOL, true statement!!
@Veloddadv6 жыл бұрын
Thanks for the video. Im about to change the seals too. Is there a trick to pull the belt and cam sprocket so reinstalling doesn't throw off timing?
@hazegrayandunderway80776 жыл бұрын
Veloddadv theres always the risk that when you pull the belt everything changes position. The cams will roll to the resting spot...the crank will be ok. Unfortunately you'll have to make sure everything is lined up. Sooo....while your in there change the belt, unless brand new. And for god's sake get OEM parts..seals especially
@RPMzRUDY3 жыл бұрын
I am in same position, so you DO need to remove manifold to set TDC (Top Dead Center)
@ibxlegendx5 жыл бұрын
how did you get the pick in there? once seal comes off will cam roll or stay in position?
@hazegrayandunderway80775 жыл бұрын
If belt is off, cam will roll for sure
@ibxlegendx5 жыл бұрын
I already did it with a big flat head. Drilled two holes next to each other. Got the flathead in carefully to widen it and started to rock it carefully up and down and mine came out easily.
@ibxlegendx5 жыл бұрын
Im suprised it didnt roll
@SWFLJetSkiRiders Жыл бұрын
Suck a amazing info there buddy, thank u so a lot. How's the car now ?
@dcmdylan1236 жыл бұрын
An update on my part after getting all the parts gaketsvand so on i lapped all 24 new valves by hand replaced steam and cam seals i even bought new lifters and head bolts i was torqued the rear head like it says on the book then i said to my self well while I’m here i should actually torch the rocker arms to 23 like the book also states... and i snap 2 damn bolts in the head go figure
@dcmdylan1236 жыл бұрын
How’s it going I’m going threw this right now as far as the broken time belt and I’m having hell if you have time can you message me i would greatly appreciate and i greatly appreciate the vid thanks in advance
@hazegrayandunderway80776 жыл бұрын
Dylan Morris if the timing belt broke you probably bent valves on this interference engine, but there is a slight chance you didn't. It's a bitch, but you can fix the belt then do a Compression check on the cylinder, but I'm afraid you'll fail because of bent valves. Sorry man. So I would pull the heads and get them redone, or do it yourself like the video. Valves are about 90.00 to 125.00 bucks. The rest is your labor. It will be big bucks at the shop. Not much good news I know.
@dcmdylan1236 жыл бұрын
SCPO USNAVY can you look me up on fb Dylan clay Morris and message me? I appreciate the reply
@dcmdylan1236 жыл бұрын
I pulled the front head today valves are bent pretty bad
@hazegrayandunderway80776 жыл бұрын
Dylan Morris pretty standard. Both heads will be. Make sure you inspect the cylinder tops too for damage, they should be ok. If you have the cash, you can take the heads in to get redone. You can do yourself. Make sure you re place valve seals and cam seals too. Take your time. Lap the valve seats too. You got this. Check Amazon for all the parts and gasket kit.