Thank u dawg I damn near threw my Yukon xl 04 away because I was losing oil and got underneath an seen it’s trail from up top coming down on the driver side all the way to dripping off the filter and pan thought it may be a head but no tail smoke no pressure lost I looked where u said an I be damn if it wasn’t the gaskets on both sides 😂😂😂😂😂

I thank you for your video. I did a gaskets change today. And I found a trick on the passenger side cover. If you take all but the last dolt out you can move the coile pack up enouck to get to all four cover bolts and it all came out with no problem

Thank you so much for this video. I thought it would be a hard job but you proved me wrong and I'm gonna try this on my 2001 Chevy myself Sunday. Wish me luck

Ppl say the passenger side is the most difficult. I felt like I was watching a Bruce Willis movie. Like he's not gonna make it in time...JUMP!! Thanks Homie

That is one the best and most informative, videos I've seen, very helpful,and I appreciate the way you finished performing what you were explaining,most ppl just say "well you get the picture" ,thank you very much.keep up the good videos

This was a great detailed video!! Certain things aren't hard as we think. The only thing is we just don't know about what's going on. I said a few months back that I wanted to start working on my vehicle. With this video, I'm one step closer. Lol.

Nice video. Love it. I'm not mechanic but I try to learn new things everyday and so I watched this video 1 time and realize how very simple it is working on my 5.3L Vortec and other GM

This is exactly the video I've been searching for, very helpful....

Absolutely amazing video best one handed video I've ever seen, with no frustration you deserve 2 thumbs-up buddy.

Really good, very detailed video. I'm planning to replace my valve covers and this is the video I was looking for.

Very awesome video!

Perfect Video. I will be replacing my covers this week

You are the man. Thank you for this. Blessings to you.

Thank you so much this really helped me out I was about to pay someone to do it

you talk to nature, and so straight and forward like your video

I've actually worked on truck where we literlly took it all apart. A good way to clean all engine parts (obviously not any electrical parts) is with gasoline. Just get a little tub or anything that you can place the parts on and fill it with some gasoline, get a brush and wet it with the gasoline, and brush clean your engine parts over the gasoline. It's just better and safer than washing engine parts with water, since theirs always a risk of leaving water in hard to reach places. Gasoline will just leave your parts super clean and its safer than water when it come to engine components.

Clean the valve cover in the inside too

Thanks for the video. Straight to the point!!👍👍👍

Lots of help doing my chevy

Hopefully this fixes the issue of oil leaking onto my sparkplug threads.

Thank you, thank you, thank you!!!

Excellent video. Thank you.

My 06 Chevy Silverado squeaks. Allot any videos for that my boy ?

How much would you charge for a job like that. Nice vid !!

Super nice video thanks!

Fantastic video.

Do you need any type of adhesive before you put the gasket on or can you just put them on like that

Great video bro thank you so much

Thanks good video 👍

thank yu ths is video

Nice job man

Could the valve cover gasket cause my 2001 suburban to give codes p0171/p0174 I spay the edge of the valve cover when running and motor idle changes

Good video 🔥

This is the same engine type in my hummer H2 except for I have a 5.7 instead of a 5.3

When you disconnect the vaccuum line for the break booster do you then have to bleed the brakes because theres air in the system now? Idk

What is the little gasket that fell for

Knock sensor how do you replace the knock sensor cause mines bad, and has to be replaced also at the same time?

.... Why wouldn't you clean out all the caked on oil? It has an incorporated PCV that can get clogged and cause major issues

Hey guys does anybody know where that little gasket goes? With the 2 holes

You know what torque is.

whats the torque spec on those 8mm?

You didn't reconnect the hose for the brake booster on the drivers side and didn't reconnect the the breather tube that runs from the valve cover to the throttle body on the passenger side. At least not in the video.

What The other part for

@ 19:43 😳 twilight zonin

You didn't even put the plug wires on all that way

Sorry (spray)

Go 4K or go home !! It's 2020 for Gods sake, post a $K video !!!

This was a great detailed video!! Certain things aren't hard as we think. The only thing is we just don't know about what's going on. I said a few months back that I wanted to start working on my vehicle. With this video, I'm one step closer. Lol.

This was a great detailed video!! Certain things aren't hard as we think. The only thing is we just don't know about what's going on. I said a few months back that I wanted to start working on my vehicle. With this video, I'm one step closer. Lol.