2003 - 2009 Toyota 4Runner Backup Camera Install

Рет қаралды 35,439

Жыл бұрын

Parts used linked in the description below!
Watch a full tutorial as a 2007 Toyota 4Runner will have a backup camera installed to an existing aftermarket radio. We will be using the Natika license plate mountable camera which will be installed in the rear liftgagte of our 4runner.
This video applies to Toyota 4Runner models for years 2003, 2004, 2005, 2006, 2007, 2008, and 2009. This video also includes kick panel removal, complete installation for the camera, wiring, and testing!
Click here for part 1 where we installed the radio on this 4runner:
• 2003 - 2009 Toyota 4Ru...
Click here for the older version of this video:
• 2003 - 2009 Toyota 4Ru...
Click here for the amp / sub install on this 4runner:
• 2003 - 2009 Toyota 4ru...
Click here for the front door speaker install on this 4runner:
• 2003 - 2009 Toyota 4Ru...
Click here for the rear door speaker install on this 4runner:
• 2003 - 2009 Toyota 4Ru...
If you have any questions, leave a comment below! Be sure to like and subscribe!
Backup Camera used (Amazon Associate Paid Links):
*Natika license plate mountable camera: amzn.to/3csfJn3
Other Parts Used (Shown in the radio install video) (Amazon Associate Paid Links):
Parts Used (Amazon Associate / eBay Partner Paid Links):
*Pioneer AVH-1440NEX Apple Carplay Radio: amzn.to/3dYk56M
*Crux SWRTY-61J Stereo Harness adapter (retains factory JBL Synthesis Amplifier): amzn.to/2T1yw2m
---Use the Crux SWRTY-61S Wiring Interface for the non amplified version: amzn.to/3iqHcK7
*Metra 95-8210 Dash Kit (Used when replacing a radio with RDS): amzn.to/3kKKb1b
---Use the Metra 95-8202 for Factory non RDS Radios: amzn.to/3gNTSJM
*Pioneer Parking Brake MicroBypass: ebay.us/RVf61w
*Hosa YRA-154 3.5 mm to RCA Female Cable: amzn.to/3wakBW4
*MOTONG Male to Female USB Power Port Socket Adapter for Toyota VIGO(42 22mm): amzn.to/2U02lRm
Disclosure: As an Amazon Associate I earn from qualifying purchases

Пікірлер: 73

@ProvoBeastAudio Жыл бұрын

Parts used linked in the description of the video!

@bryanfeely650 Ай бұрын

OMG what a great video! My son and I just installed a back up camera and apple car play interface for his 2009 4-Runner! Your video was SO easy to follow - thanks again!

@JonFox1945 22 күн бұрын

Is it a v8? 09? Trairunner edition?

@bryanmartinez435 Жыл бұрын

Thank you so much for this video. Quick to the point and very informative. I followed it step by step. The only hard part was fishing the wire with the hanger. I zip tied that wire so well, I still don’t dare roll that back window down 😂

@squarecatcreative 2 ай бұрын

Super useful details-especially at the hatch wire routing!👏

@ProvoBeastAudio 2 ай бұрын

Thanks!

@pjrainmaker Жыл бұрын

Also, for accessory power, you can tap into license plate lights on most vehicles because they are on with accessory power

@stevewynn2307 6 ай бұрын

Thank you for the great video. Hardest part was fishing the wire through the liftgate/back door.

@akutell 11 ай бұрын

Thanks for the video, I'm doing the same install. I was wondering, though, why you chose to install the wire through the driver side and ignition area, instead of the less-busy passenger side with it's easy-access behind the globe-compartment?

@4thgenhunter Жыл бұрын

Going to try this now!

@ItAintMeBabe99 Жыл бұрын

Great video ! Sure wish I knew what a loom or reloom is !

@TheBEAST-ej7oo Жыл бұрын

Hii thanks so much for the video, I have a doubt do we need to buy a cable for the length needed to install the backup camera? Or the ones that comes with the screen and cámara is enough? Thanks

@Dean-dy4jf 7 ай бұрын

Hi, great video. I have a question about the wiring. Instead of running the separate "trigger wire", couldn't you just connect the trigger wire that comes with the reverse camera to reverse camera power and then bring that to the front (with the yellow video connection) and then plug the trigger wire at the other end into accessory? Then simply run a wire from the trigger wire behind the head unit to the brake wire under the dash that is powered when you put it in reverse. This is the red/yellow wire under the dash.

@kpboix99 3 ай бұрын

Thank you for showing the process to get the wife fed in. Just ordered a camera online and knew KZfaq had the answer!

@felixwong7242 Жыл бұрын

Awesome tutorial

@ProvoBeastAudio Жыл бұрын

Not the easiest backup camera to install, but certainly doable!

@RyanPrice01 Жыл бұрын

For those models with the factory nav and backup camera, can you use the existing camera with a new aftermarket radio?

@ImperatorCaesar22 10 ай бұрын

Hey I bought my car used and it has a very similar radio and backup camera, but the backup camera isn't working. Any idea on how to begin to troubleshoot?

@pjrainmaker Жыл бұрын

The wire the powers the reverse light comes from the front. You didn’t need to run an additional wire. Just tap into the same wire you’re using in the back, just do it under the steering wheel

@kyleosher3916 6 ай бұрын

Great tutorial thanks! I chose to go with Option 2. Hooked everything up, but I don’t think the cameras receiving power. Do I need to complete the circuit with the red accessory pigtail by connecting it to itself back by the taillight?

@ProvoBeastAudio 6 ай бұрын

No, it’s one or the other. If you connect one end to accessory and one end to the reverse light, you can backfeed your reverse circuit and cause damage. If the camera isn’t getting power, check your accessory wire or be sure it’s still grounded.

@s2000pill Жыл бұрын

Are you in Provo? I will drive there from Los Angeles LOL! I need this done for my mom's runner

@paulreetz8466 Жыл бұрын

Great video! With your implementation and this Sony unit, will the backup cam view interrupt CarPlay if it is active? I assume yes but I've read some stereos won't interrupt when you go into reverse if CarPlay is on.

@ProvoBeastAudio Жыл бұрын

Yes, all brand name units will interrupt any source to display the reverse camera as long as the radio's reverse trigger wire is properly connected.

@jerryray808 Ай бұрын

im going Sony as well. Crutchfield recommended for the Jbl system T4R. and will supply dedicated connections.

@Terences123 2 ай бұрын

What do you do with the parking brake by pass

@Jextremegamer 6 ай бұрын

Hello, so basically if I want just a normal back up cam. Just hook it up to the reverse bulb both neg and positive and then the yellow rca to the radio and the remaining red wire to the purple white infront. Corrent? Thanks

@ProvoBeastAudio 6 ай бұрын

You got it buddy.

@imranabbasi7871 Жыл бұрын

Awsome 👍

@InMn Жыл бұрын

Sp the front trigger wore connects to the acc. Where does the red trigger wire on the rear part on the harness connect to?

@ProvoBeastAudio Жыл бұрын

It doesn’t, we tape it off. Camera gets power from accessory up front, red wire back at the camera we insulate, and ground connects to ground of reverse light.

@s2000pill Жыл бұрын

how long does it take?

@stuartfact8361 Жыл бұрын

I watched this video 8 times already and can’t figure out why my setup is not working. I had to extend my RCA cable because it was not long enough to reach the front of the car. Will the camera still get power if the cable is extended, but is only a regular RCA, not one with the auxiliary power wire? PLEASE HELP I’m so close to being done!

@ProvoBeastAudio Жыл бұрын

Send us a message on our facebook page and we can assist.

@whylee13 Жыл бұрын

I followed this guide and have made it all the way to the stereo using the second wiring option. However, I'm getting "No Signal" for the R-Cam. The trigger wire works, when I shift into the reverse, and the accessory wire shows 13V of current on the multi-meter. So that only leaves the RCA connector. Any thoughts?

@ProvoBeastAudio Жыл бұрын

Camera isn’t getting power. Ensure if wiring it to accessory, to ensure it’s connected as well as the ground.

@whylee13 Жыл бұрын

Edit: I found out there was loose between the backup camera and the extension cable. I had to fish the connection back out, push the connectors together, tape the crap out of it, and pull it back in place.

@revolutionunderground Жыл бұрын

@@whylee13 🥹

@Terences123 2 ай бұрын

I’m doing option 1 so I just run it to the stereo and connect my red to violet white and plug my rca into the pioneer stereo

@alejandrogonzalez3285 11 ай бұрын

Nice very nice

@sergio_ivl 6 ай бұрын

What model of Sony radio is it?

@johnkimx83 10 ай бұрын

The 4runner I bought already has an aftermarket camera installed. Can I swap out the camera and just plug it into the existing wiring?

@ProvoBeastAudio 10 ай бұрын

Depends on the camera, depends on the wiring. Maybe? Not every camera uses the same wiring harness.

@revolutionunderground Жыл бұрын

I'd like a backup and dash camera with loop recording, on when key is on lol

@mariocabron1653 Жыл бұрын

What kind of radio ?

@mrnoedahl Жыл бұрын

Great job my hillbilly friend.

@4thgenhunter Жыл бұрын

Wow this was difficult 😅 I had a really hard time trying to get the cable through the channel in the side of the trunk

@ProvoBeastAudio Жыл бұрын

Yep, not a great design by Toyota!

@SLickev92 Жыл бұрын

I had a hard time as well , I was using fiber glass fishing Rod. I switched over to the wire hanger and Much easier. Now I gotta go through the boot, 😩

@christophercrispin5605 Жыл бұрын

I did it verbatim how you said, and now my radio won't turn on unless I put it in reverse. I took everything apart, and made sure it was back to original wiring without backup camera, and the radio won't turn on at all now.

@ProvoBeastAudio Жыл бұрын

Sounds like a wiring issue. Check your fuses. If your radio only turned on while in reverse, you have some major wiring issues and potential blown fuses.

@ProvoBeastAudio Жыл бұрын

Refer to this video for your radio issue: kzfaq.info/get/bejne/rqqagJOmp53KnGw.html

@ProvoBeastAudio Жыл бұрын

Also ensure your backup camera is NOT powered by BOTH the reverse light and the accessory red wire. Doing so can cause major damage

@christophercrispin5605 Жыл бұрын

Thank you. I figured everything out. The only thing now is I keep blowing the IG1 fuse which is the reverse trigger for the stereo. So everything is fine until I try to put it in reverse.

@christophercrispin5605 Жыл бұрын

@@ProvoBeastAudio so just to reiterate, I disconnected that “extra purple wire” going from reverse positive power from tail light to reverse gear input signal. That stopped the fuse from popping and the camera still works when I select it on the stereo, but now I don’t have a trigger for when I go into reverse gear

@armondhammer9 Жыл бұрын

The rare 3rd row.. I've only read about them. If this thing is 4x4 it's a Unicorn.

@blueworld25 6 ай бұрын

Hello there! I’m in Utah and need a similar job for a 2005 4Runner how can I get in touch with you?

@ProvoBeastAudio 6 ай бұрын

Send me a message on Facebook or Instagram

@tonydize3944 Жыл бұрын

What radio is that i like it

@machina_aeterna Жыл бұрын

Where do you connect an aftermarket back up camera?

@ProvoBeastAudio Жыл бұрын

To the camera input of the radio.

@pjrainmaker Жыл бұрын

You keep mentioning that there are no trigger wires because it’s an old analog car. Cars still use the same electronic signals but with the addition of CANBUS, a digital signal that carries binary code, but you don’t use them for triggers anyway. So the comments about the old analog car are really ridiculous. Just think about it, does the backup camera kit come with different equipment for connecting it up to a new digital car versus an old analog car ?

@bryanbearden4448 7 ай бұрын

Gone 10 years without a camera. After watching this pain in the ass, I'm happy without one

@user-qs2cz6qn5m 8 ай бұрын

i have the same car and i did everything the same shown in the video and im getting a black screen

@mariop.2758 8 ай бұрын

Could the screen have problems? If screen was tested prior double check your wiring..

@jovani7346 Жыл бұрын

Brother, need some big help. I was able to get the wires through to the tail light and ran to the front of the truck. I cleaned everything up to finish another day and now the tail gate doesn’t latch when closed. I was very careful through the process. Do you have a possible solution?

@ProvoBeastAudio Жыл бұрын

Unplug the harnesses from the lift gate modules on the driver side, remove the negative off of the battery, wait a few minutes, reconnect harnesses and negative on battery. That should reset the module in the lift gate.

@acdcjake3850 Ай бұрын

I heard AC/DC playing in the back ground.....lol

@SolanoPolancoJunior1284 Жыл бұрын

Hola😅

@ProvoBeastAudio Жыл бұрын

Hey!

@DpDm-jx4iu 6 ай бұрын

The video is helpful but he does a terrible job of explaining and talks too fast

@ProvoBeastAudio 6 ай бұрын

Wow, thanks. I have people complain my videos are too long, or too short, or talk too much, or talk not enough. I can't satisfy everyone, so I do my best. I'm sorry it's not up to your personal standards.

@jerryray808 Ай бұрын

Us old buzzards need it a little slower. Like having a 20 yr old tell you how to program your computer.