2005 - 2010 honda odyssey sliding door roller replacement

No video

2005 - 2010 honda odyssey sliding door roller replacement - most common fix

Рет қаралды 17,667

Күн бұрын

2005 - 2010 honda odyssey sliding door roller replacement - most common fix
This week I show you how to remove and replace the sliding door roller on a 2005 - 2010 Honda odyssey. Its not too difficult but it does require a little time and patience, all you need is a couple of tools (listed below) and the replacement part Ill leave a link to them below.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
Tools/Material -
Screwdriver - amzn.to/39ZQBX0
Needle nose pliers - amzn.to/3yTT2V7
Painters tape - amzn.to/3nP26UI
Impact - amzn.to/3ABUtIX
Socket set - amzn.to/3yLJpGP
Sliding Door Roller Assembly - amzn.to/3PcBclh
Video Shot on
z cam e2- m4 - amzn.to/3wr5PvD
canon 24-70 - amzn.to/3wb6pP4
I hope you enjoyed this weeks video! Be sure to like share and subscribe! Also if you have any questions or comments be sure and leave them in the comment section down below! Consider supporting BS with AJ on Patreon so we can do bigger and better projects for you guys to see! Thanks for watching and ill see you next week!
Facebook - / bswithaj
Patreon- / bswithaj
BS with AJ KZfaq Channel - www.youtube.co....
twitter: @BSwithAJ

Пікірлер: 54

@cesarwo12345678 5 ай бұрын

You are the best !!! I have saved hundreds of dollars with the mechanic; It's a matter of patience, nice video and thanks a million

@BuildStuffwithAJ 4 ай бұрын

Great to hear! I'm glad I could help!

@StrengthOfYah 2 ай бұрын

This helped me disconnect the cables for the doors on both of my minivans and turn them back into manual doors. I hope your automatic door systems last longer than mine did!

@fitzfunfitness5681 Ай бұрын

Just wondering what you did specifically to turn them into manual doors again? After disconnecting cables did you remove them or just cut them off?

@anitageinert7889 Ай бұрын

As a widow this was wonderful. The only hard part is putting the cable back in. We discovered that the instructions should include using baby vice grips to pull the cable to get enough slack to insert the small cylinder. We really struggled for at least 30 minutes before we figured this out

@BuildStuffwithAJ Күн бұрын

I agree, this was by far the hardest part of the repair for me as well

@makowskid8 28 күн бұрын

Thank you for the exceptional video, I know it had to have saved me from atleast a minor headache if not more!

@BuildStuffwithAJ Күн бұрын

Glad it helped!

@gadfly96 7 ай бұрын

Awesome video! Great talk through of the entire process. Thanks!

@BuildStuffwithAJ 4 ай бұрын

Thank you! I'm glad I could help!

@Rika_Noodle Жыл бұрын

I needed to replace the roller mechanism shown at 9:50. I'm new to car repair, and had never seen a pin like that before. Had a couple unsuccessful attempts at removing it. Never would have guessed it required smacking with a hammer. Thank you soooo much.

@BuildStuffwithAJ Жыл бұрын

I am glad I could help!

@user-cl5gz8fl5o 7 ай бұрын

Wow. This was amazingly detailed and really helped me out with my minivan. Our sliding door rollers looked about like your old set there and it's been driving me crazy. Thanks for sharing your knowledge.

@BuildStuffwithAJ 4 ай бұрын

Thank you! I'm glad I could help!

@joelbennett9009 7 ай бұрын

Done in under 30 minutes woooo woooo thank you !

@BuildStuffwithAJ 4 ай бұрын

Awesome! Great Job! I'm glad I could help!

@user-rn3kc2bi1r 6 ай бұрын

Awesome video, I just did drivers side , piece of cake. Thanks for giving me the confidence to do the job. Thx for sharing.

@BuildStuffwithAJ 4 ай бұрын

Glad I could help! Thank you for the comment!

@stanmccorkle Жыл бұрын

Very grateful for your video. You saved me lots of exploration and the breaking of more parts while exploring.

@BuildStuffwithAJ Жыл бұрын

Glad I could help!

@nelsondesousa8855 10 ай бұрын

Like the way you masked off body to protect it. I would have used bearing grease on pin and each end of hinge... marking position of roller on door before removal makes a perfect install.

@BuildStuffwithAJ 4 ай бұрын

sounds like you have done this a time or two before lol. Great tips!

@nelsondesousa8855 4 ай бұрын

40 years at Honda kinda helps

@leavenedlives9862 22 сағат бұрын

Having done the job, I would not have been able to get the pin without removing the bracket. It took a fair amount of banging.

@Tahimate 4 ай бұрын

Awesome and thank you

@BuildStuffwithAJ 4 ай бұрын

Im glad I could help!

@Burgerdog75 Жыл бұрын

Fixing to do this repair. Hopefully it goes as smooth as yours. Thanks for your video.

@BuildStuffwithAJ Жыл бұрын

I am glad I could help!

@zdzislawkrzyzelewski4776 Жыл бұрын

Hi AJ! Excellent presentation. God bless You! I can see God's help.

@BuildStuffwithAJ Жыл бұрын

Thank you! I'm glad I could help!

@mrputter-rs Жыл бұрын

You do realize that they are asking for over 2000$ to fix that? Thx a lot.

@sorensenjay 2 ай бұрын

By the way, you can order the electric door roller part for an Odyssey with a manual door. It's a lower priced part and it works perfectly well. It has a couple of loops to accommodate the motor cable, but they are just ignored for the manual door.

@BuildStuffwithAJ Күн бұрын

Great tip!

@pobodysnerfect9270 Жыл бұрын

Thank you dude! 10/10.

@BuildStuffwithAJ Жыл бұрын

Glad it helped!

@victorweinstein2528 Жыл бұрын

Wonderful step by step video, and really appreciated the attention to detail, e.g. taking the time to zoom in to clearly show what you were doing. I have a few questions. First, did you remove a fuse to prevent the door motor from operating? Otherwise, how did you keep the motor from running? Second, I have seen it mentioned (in the Odyclub forum, for example) that white lithium grease should be used as a lubricant. Is it unnecessary to add grease to the new rollers or to try and clean out the track that the rollers are, uh, rolling on? Finally, what are the chances that it will be necessary to release the tension on the cable from the inside of the vehicle and how much complexity does that add to this process? Again, though, I want to compliment you on the excellence of this video. There's another highly viewed video on KZfaq for this same replacement and I prefer yours. Thanks.

@BuildStuffwithAJ Жыл бұрын

I didn't remove any fuses, we turned the automatic doors off a while back because they kept getting caught. although removing the fuse would do the job too. As far as the grease goes, I suggest using it for sure. I didn't because honestly it was over 100 degrees that day and I forgot lol. The tension was fairly tight to be honest, and it took me several tries to get it back into place. The reason I didn't relase the tension is because its very difficult to get to, it would have required taking a lot apart in the rear of the van. I have no idea why they didnt put an access panel anywhere for that. Thank you! I am glad you enjoyed the video! And I hope your project goes well!

@edwardmurray405 8 ай бұрын

You did a great job. Thank you

@BuildStuffwithAJ 4 ай бұрын

Thank you! I'm glad I could help!

@junocdx 5 ай бұрын

Thank you!

@BuildStuffwithAJ 4 ай бұрын

You're welcome! Thank you so much!

@leavenedlives9862 27 күн бұрын

Also, can you do this by removing the pin while the bracket is still attached to the door? If so, this would eliminate the problem of not getting the bracket back in exactly the right position since it would remain attached. Or would it not be possible to line the new roller up well enough with the bracket to reattach it with the pin?

@BuildStuffwithAJ Күн бұрын

Ill be honest, I think this would make it a lot harder of a job, Im sure it can be done this way but Id be afraid id make more work for myself

@flyxpl Ай бұрын

The whole reason I needed this video was loosen the slack on the cable and unfortunately, you don’t show that .

@BuildStuffwithAJ Күн бұрын

I'm sorry I couldn't help you, I watched several videos on how to loosen the cables before making the repair and I determined it would double if not triple the work load so I decided to do the repair without messing with the cables tension

@user-im8oc4us9p 7 ай бұрын

My door has no rollers asked machanic for repair cost but he said I had to go to a body shop. They're clueless or lazy. If I had a floor jack I'd do it myself. Parts from Honda went way up with the inflation bs

@BuildStuffwithAJ 4 ай бұрын

That sucks, Im sorry you had to go through all that. I hope my video helped you get it fixed yourself

@javoskiwhite6720 3 ай бұрын

Rock auto

@leavenedlives9862 27 күн бұрын

Will this repair work on an automatic sliding door or would that be different?

@BuildStuffwithAJ Күн бұрын

These are automatic sliding doors, but the automatic part was somehow draining the battery while the vehicle was off so we unhooked it.

@user-im8oc4us9p 7 ай бұрын

I believe it's "C" clip but I can't see it. I have seen all parts needing to be removed to get to tension release,. It's a PIA