Jeep Grand Cherokee starting problem - like and cement if this solves your issue
Пікірлер: 162
@luvdogsandhorses Жыл бұрын
THANK YOU i cleaned the ground beside the battery on fender and so far working good Cleaned both sides of washer with wire brush,cleaned bolt, cleaned fender attachment area
@lestatdelioncourt7513 Жыл бұрын
Thank God somebody finally stated where the ground was that they cleaned for this particular fuse box and relay. I've been asking all over the comments. Do you happen to own a Cherokee or a Commander?
@mitchaleshire13 жыл бұрын
You Sir, are my hero! Just wish my son could have found your video prior to 3 days of head scratching and $200 in parts on a 2005 Liberty Renegade! Turns out about 35 cents worth of butt connector and wire did trick. You are THE MAN!
@Bfalds252 жыл бұрын
I watched 6 different videos, one over 45 minutes and this is hands down, the best one. Even if this isn’t the issue with my Jeep, great video. Thank you.
@mattengelmann25912 жыл бұрын
You sir are the man this video turned my 5 hour starter replacement into a 5 minute ground cleaning don't even bother replacing the wires that's all it needs starts like a charm at 170k miles in Northern Illinois
@CarlosRodriguez-hr3ke Жыл бұрын
Thank you as well!!! Two days battling with the starter and so many wires and then I accidently grounded the wrong relay wire and blew a couple fuses but when I rerouted the correct ground wire from that relay like he showed in the video the jeep started right up!!! Thank you thank you!!!
@lestatdelioncourt7513 Жыл бұрын
@@CarlosRodriguez-hr3ke what color was the ground wire
@lestatdelioncourt7513 Жыл бұрын
Where was the ground that needed to be cleaned? Like what area in the engine bay should I look for this ground?
@manny3554 жыл бұрын
I went through and tested everything you did and when I tested that ground wire that was the problem...I spliced a new ground wire to a known good ground connection on the car...it started right up. Thanks bro! Saved me time and money.
@geraldjohnson21422 жыл бұрын
You absolutely are the man, I love this platform and appreciate the people that take time to help out others that can't afford a $1000 to have your vehicle serviced.
@billyb6116 Жыл бұрын
Man… I have an appointment at the dealer to fix my intermittent click, no start problem on my Jeep Commander. I had already changed the starter. Then had the same problem. They were going to charge me $180 diagnostic… The service guy already speculated, “if you have already changed the starter, and the fuses and relays are fine, it might be the ECM or a problem with the Power Control Distribution Center.” I’m guessing I wouldn’t have gotten out of there for under $750. Thanks. Great work… and really good video!
@davidgillettuk96387 ай бұрын
Just got exactly the same issues... many thanks brother. Best wishes from the UK 👍
@curtblanshan3 жыл бұрын
2009 Jeep Grand Cherokee, and this video saved me a ton of cash and time! I didn't have to cut any wires to ground it, but this put me on the track to fix a loose wire and worked like a charm!
@lestatdelioncourt7513 Жыл бұрын
Where was the loose wire you ended up finding located at?
@curtblanshan Жыл бұрын
@@lestatdelioncourt7513 I do not remember the specific wire but I do know I pulled the box up and checked them all.
@ronniemorgan53073 жыл бұрын
Mobile mechanic had relay no start on 2009 jeep cherokee same issue relay was in different place but I traced the yellow wire from starter solenoid up to fuse box relay tested all the circuit found hot wire was not getting power to relay thanks for your video i was stump to what was wrong found it my client is happy.
@zen8xx8003 жыл бұрын
Help
@uavflyr73273 жыл бұрын
Thank you! Thank you! Thank your!!! Had the exact same issue on my '07 for months now and this fixed the problem. Took me 1 hr. by simply jumping a new ground from the relay as you have shown. Was about to change out the ignition switch. Thanks YOU!!
@bindig12 жыл бұрын
Great video. Everyone assumes it's a major electrical issue, starter, ign switch, etc.
@georgehernandez3502Ай бұрын
It’s been awhile since this video came out but thank you that helped out my issue right way, very helpful video and str8 to the point
@OnVacationNow3 жыл бұрын
Outstanding brother. I did it and the results are perfect. Just wish I would have found this video before I purchased and changed the starter. It worked on my 2006 Jeep Commander. Again THNX. Mac
@VanHarding2 жыл бұрын
Thank you - you are a good diagnosis & detective!!!
@williamrenz89562 жыл бұрын
Bro thank you you said yourself you were in a rush however thanks for making that video I have the same issue one night I try to turn key over and just clicks I'm like wtf was just working. Ended up working again until a few days later same thing. I'm gonna do as you did and will reply with the conclusion.
@kirk1059 Жыл бұрын
This is exactly what's wrong with my brothers jeep thank you I'll do this for sure tomorrow when I have more daylight
@jaipeters48667 ай бұрын
Thank you so much for this video, extremely helpful. I truly appreciate your willingness to take the time and make a video solely to help other people out with there own repairs. Thank you kind Sir!
@Westcoastjazzer7 ай бұрын
I have the twin to this Jeep, It even has the same air freshener on the same vent. Had to have it towed home the other day with the same problem that has been a off and on problem for a couple years now. Can't trust the old girl! I was planning to change the starter when time permits but now I'm going to test as you did. Thanks for the tip! It all makes sense now! Stand by for an update..........
@livewireblanco6 ай бұрын
Did it work?
@JstAbase_c63 жыл бұрын
I'm going to try this on my buddy's jeep, its been giving him hell couple years now. I'll leave a update how this turns out. great advice
@TeamRegulate223 жыл бұрын
Most jeeps seem to be the actuator pin
@alecfacemire10203 жыл бұрын
Did it work?
@jaykincer78692 жыл бұрын
Thank you so much for this video! You saved me another expensive trip to the dealership. Worked perfectly for my 2006 Commander 4.7.
@lzambra472 жыл бұрын
You are alright Man, I am dealing with exactly the same problem. Thanks a lot.
@henrynewsom69064 жыл бұрын
Hey I have a 2007 jeep Laredo grand Cherokee. I just did this and it worked perfectly. People was telling me it was the starter but it wasn't. So thanks alot for this video it saved me 150 dollars. But I was wondering if I can continue to drive it like this
@GlifordJean4 жыл бұрын
I still own the car and it's been driving just fine ever since.
@TheDcrocks13 жыл бұрын
Did you keep driving it with a problem?
@XTRABIG6 ай бұрын
thanks.
@jimtresider804611 ай бұрын
exactly what I got going for me . I hope it works for me. Thank you
@80-_ Жыл бұрын
My 2008 Commander just did the same thing this past weekend. It worked fine in the morning then went to start it in the afternoon and just got clicking sound. I was going to make plans to repair it but will check the relay first. I have good voltage on my battery also.
@HorsepowerHouse2 жыл бұрын
Just check, clean and improve all chassis grounds relating to those areas. Should solve the problem for anyone viewing this. I do this on any older vehicle of mine. Battery to chassis, chassis to engine, ending to frame, engine to chassis, always check, clean, tighten those grounds. Or replace the wiring if they are suspect. Same on ANY motor vehicle, motorcycle, atv, ANYTHING.
@magalyquinones34242 жыл бұрын
Thank you your video saved me from being stranded.
@bobmcnelis36482 жыл бұрын
Good job Cliff! Those leads and contacts under the fuse/relay box, are the problem with mine. Again, no ground, but the contact on the end of the ground wire was corroded, and not making a good electrical connection. Now it cranks, but doesn’t yet start, I suspect that there are other problems of the same type in that wiring of the box.
@nathancarlson782 Жыл бұрын
Was about to buy and install a new starter but gonna try this first... Identical problem on my end! HOPEFUL!!! :)
@eurm128 Жыл бұрын
Thank you to help, this video was really good for me, please could you to do a heat transmission video when pull a trailer; I have big problem. Thanks in advance.
@beverlychapa5663 Жыл бұрын
Thank u for this video if it wasn’t for me and my dad my brother would of spent alot of money on his jeep love the video! Hope it goes to more audiences that need this video 👍👍👍
@tortugaclan3 жыл бұрын
Great video, helpful. And no bs.
@rebeccacollins47903 жыл бұрын
I was having the same exact problem on my 2009 Jeep Commander and it was the wires underneath the ones closest to the driver side it was a yellow wire I think it was part of the wiring harness good. But I cleaned it really good and all that and now it works just fine, and it did it multiple times like I probably had it happen to me 15 times
@kamillop.78423 жыл бұрын
Hello, there is one shortcut path here, the (-) on the relay electromagnet is not always conected with GND, this signal is comming from powertrain control module, so your solution will work but you can also run the starter in cases when normaly you can't do this, i.e. in case enginee is running already.
@daltonadriel35973 жыл бұрын
you probably dont give a shit but if you're bored like me during the covid times you can watch all the latest movies and series on Instaflixxer. Been streaming with my brother lately xD
@sethbriar82213 жыл бұрын
@Dalton Adriel Yea, have been using Instaflixxer for since december myself :D
@calgaryjammers48213 ай бұрын
Great video. thanks for the valuable info
@chrisbuskirk39762 жыл бұрын
got a 07 jeep with the same problem that you for the video
@gohan31319853 жыл бұрын
Mine was doing the same but what you did does work thanks sir
@GlitchEmpireBrett Жыл бұрын
I tried this and it don’t help and my dash now has no power any advice I have a 2000 jeep grand Cherokee limited
@tjanders9863 Жыл бұрын
Your a smart man!!! This was a helpful video as I have the same issue with starting my jeep .thx
@thomasbirzer77293 жыл бұрын
I have the same Problem with a 3.0 crd. I will try it tomorrow. Thanks for your vid.
@DFWTF2 жыл бұрын
This should of been a recall what a load of shi@
@teowaiwaaka23533 ай бұрын
Mean bro that worked 4 my jeep diesel thanks my bro
@henrytaylor3049 Жыл бұрын
Great explanation, appreciate you making this video 👍👍👍
@QRS365 Жыл бұрын
good catch bro. that was a good troubleshooting procedure
@basilreardon57833 жыл бұрын
Thank you sooo much for your guidance on this problem . Your fantastic .
@michaelearlharper50993 жыл бұрын
Lake Mmjj
@themoonman-42 жыл бұрын
Saved us with one! Huge help Thank You!
@TheSman17310 ай бұрын
Thank you brother! Definitely the same issue
@trevorpeden21802 жыл бұрын
Not sure if this is my problem but I may be returning the new starter I just bought.
@trevorpeden21802 жыл бұрын
This was not my problem however I didn’t have the best ground at the relay so i did leave this trick on my Jeep. Turned out I did have a bad ground but was at the starter the bolt was loose. However I did end up replacing the starter because it was a pain in the you know what to change so I put in a new one. Still this helped a lot thank You.
@damianreed1473 жыл бұрын
I´ll check it out. Great Vid, Thanks a lot.
@1Guernelli2 жыл бұрын
Best video! Thank you Gilford
@laurvesingi9576 Жыл бұрын
if my starter ground is showing 12 v, what should i look into next?
@jimtresider804610 ай бұрын
My issue was a small Clip/ spade connector which was loose attached to the starter , I had those exact symptoms. It was not the ignition switch , it was not a ground issue at the relay box .
@troyjones27722 жыл бұрын
Thanks your video saved me alot
@damon123jones Жыл бұрын
Ok i did mine last night and today its started first turn evdry time...yaya thankyou
@johandejager10343 жыл бұрын
Had the same problem - earth wire at bottom leading to starter motor attached to chassis need to be cleaned
@Mo-fc2vj3 жыл бұрын
I tested the negative and it read full 12.85V Edit : the problem was the negative connector to the starter was loose at the starter i clipped it with pliers and no more problem
@jorgemora71908 ай бұрын
Great job thakns man god bless you
@TheBriskOh4 жыл бұрын
My Jeep will start when its been sitting for at least a few hours then it doesn't start after I drive it around and turn it off. Is that issue you had?
@theharoonbuilds53104 жыл бұрын
Same here , you got a diagnosis and solution?
@brendanunderwood25423 жыл бұрын
^^^
@junit4833 жыл бұрын
Sounds a lot like heat soak
@kakachattha3 жыл бұрын
@@theharoonbuilds5310 is it diesel or gas. I had diesel and had.problem. changed injectors
@Skyskwatch2973 жыл бұрын
Thanks. Gonna try it on my 07
@hortanium3 жыл бұрын
You can never have enough ground wires...they deteriorate...always check your ground wires...
@cardude19576 ай бұрын
I'm having this issue and I just replaced the starter and it didn't solve my problem. This fix doesn't make sense though. If the relay clicks, then you have ground on pin 85 of the relay, and power from the ignition on pin 86. When those are activated, the relay closes the path between 30 (source power) and 87 (output). 87 of this relay goes to the spade connector on the starter. The thing about this fix is, all you did was connect pin 85 to ground, but if it was a good enough of a ground to click before the fix, then it was a strong enough ground... I'm not saying that Chrysler doesn't have terrible grounds all over the car, because they do. I just can't make sense of this fix. A relay doesn't click but not work unless it's broken...
@thomasdowd1960 Жыл бұрын
that fixed my Jeep Liberty Problem .... Bad Ground Mouse in the House
@Mattyd09973 жыл бұрын
Okay this is my problem, but I really need help. I disassembled the fuse box to get to the spark plugs and put everything back together and now my cars not starting saying service 4wd and service electric brake system. It’s not even turning over. So I think it’s the ground like you mentioned but it’s hookup up. :/
@bensalazar4561 Жыл бұрын
Great video helped a lot thank you 🙏
@manuelmolina67813 жыл бұрын
Good job man!!
@welz10044 жыл бұрын
Bruh i have a 2006 grand cherokee and it just stopped turnin oncoutta no where, makes a weird noise when i try to start but it aint startin
@bossvizionfilmz3 жыл бұрын
My jeep did the same to me today I’m gonna try it out
@annumma34402 жыл бұрын
What happens if you end up getting good ground what else can be the problem
@selador112 жыл бұрын
Thank you!!!
@paoloangeles951 Жыл бұрын
about to try it on my 08 jeep commander hope it works thank's in advance!
@SantoshYadav-kk1uo3 жыл бұрын
Nice information
@jeepsblackpowderandlights4305 Жыл бұрын
Had a feeling it was the ground.. my friend is having the same problem with their 98.. i keep telling them the ground or positive cables.. need cleaning or traced and cleaned.. or reppaced.. but they just keep cleaning the battery terminals.. but not the other ones
@mikejohn1059 Жыл бұрын
Yo gud shit bro! Thanks alot.
@904geez183 жыл бұрын
So I'm not getting a click from the starter relay and I replaced it and ran a ground from the starter relay to the driveline federally like you did and I get nothing from the relay and yes I did get a new battery. Removed the starter and tested it which it passed and also put a new female on the Yellow wire nothing any recommendations?
@Mo-fc2vj3 жыл бұрын
Test the relay if it's getting power when you crank the key if not I'd start looking around the ignition cylinder
@ralphnabozny8494Ай бұрын
good for you
@carlmartinez44754 жыл бұрын
Please help. I have 12 v in the second hole to the starter... ground is good 12v. Even the one to the ignition is good. But the first hole where u said it's always hot I'm not getting anything what could I do there? Would it be the red wire that connects to the starter because the wire under the relay hole is red.
@MMN4033 жыл бұрын
Clean the ground on the starter from the corrosion. And it will 100% will start
@haboobamaddyabbanga82422 жыл бұрын
I have the same issue please help when you get help
@MrTrelly103 жыл бұрын
im prayin its the ground wire because i just bought a starter relay yesterday then it worked i came in the house came back out and it wouldnt start again man im sooo pissed 😤
@damon123jones Жыл бұрын
good man, iam gonna try
@dominicmancini17663 жыл бұрын
Thx ther going tow mine hope fully that will work
@robertodonnell88073 жыл бұрын
I think you have bridged out the neutral start switch? Can you start the Jeep when it is in R and D now?
@warrensantiago4961 Жыл бұрын
What if I’m getting no volts from the ground would that fix still fix my issue?
@americanflower68593 жыл бұрын
Thank you so much.
@jensen5668 Жыл бұрын
Thx chief!
@toddmatthews5376 Жыл бұрын
I'm having that same issue in my 1996 ZG grand cherokee Laredo. Turn the key, dash lights come on and everything as it should then when I go to crank it over the starter relay clicks but nothing else happens so ill have to buy a multimeter and try this out.
@johnm4579 Жыл бұрын
I have same problem on 2010 jeep commander, same no crank issues. did a new starter and relay, new battery and same issues.
@fbgwedgie4 жыл бұрын
Which wire did you hook the new ground up 2
@GlifordJean4 жыл бұрын
You can simply run a ground from the left side wall to the green and pink ground relay #33
@fbgwedgie4 жыл бұрын
Gliford Jean the two separate wires under the relay?
@melvingarcia29922 жыл бұрын
@@GlifordJean I belive the ground cable is yellow?
@lestatdelioncourt7513 Жыл бұрын
@@fbgwedgie Jesus Christ no it's a green and pink like the wire is both colors not two different wires
@lestatdelioncourt7513 Жыл бұрын
@@melvingarcia2992 and you don't need to get on here confusing people the yellow wire is what everybody else is talking about on the starter. If you watch his video and follow along you can see him pointing at the green and pink meaning that it's both colors not two different wires the green and pink wire is the ground wire that goes to relay number 33 that you have to give a good ground if you want to bypass finding the ground that goes to that particular relay box and just clean it but both solutions work. The freaking yellow wire goes to the starter and that's same issue but not what he's talkin about and that's a completely different area to check if you're having the same clicking problem he was trying to show you what to do in case you check that yellow wire going to the starter if it's not the issue then it's the pink and green wire going to the bottom of relay number 33 don't get on here confuse people Jesus Christ
@johnelliott45213 жыл бұрын
Weird, same problem same solution, must be a common jeep issue
@juvevalerio32403 жыл бұрын
Dude!!!! I have the same problem. Now I now I can try that.
@uavflyr73273 жыл бұрын
It works! I just did this on my '07 that had the exact same clicking of starter random, no starting issues and this fixed the problem!
@zamfambam2 жыл бұрын
So just connect the yellow wire to the fire wall.
@miroslavpetrov803 жыл бұрын
Yes it helped me! Thank you!
@paxanda66622 жыл бұрын
👂🏻this is what I'm hearing 💯 I'll be back with results 😊❤️💕💕💕💕💕🤗💕💕💕💕💕
@lifehunter642610 ай бұрын
The bad ASD (Auto Shut Down) relay will make it do the same thing
@mammothether3049 ай бұрын
I am having the same click when trying to start. My ground and "always hot" are 12 volts. Back to square one lol
@ghungroo3850 Жыл бұрын
I have the same problem on my 2010 sentra , I think it does not have a starter relay , it has an IPD module. It clicks , no start.
@roberthidalgo43215 ай бұрын
Your story really is burned out $6 for a new one take your horn relay put it in place for your starter relay and then go buy a new horn relay
@adorablyadorable56652 жыл бұрын
I just put front struts and upper arm and wheels back on and the 2006 Jeep-Grand Cherokee will not even light up the interior lights, dead as a door nail. 12volts on the battery not sure about amps.
@GlitchEmpireBrett Жыл бұрын
I am goin for try this when I get home
@koreyholmes54553 жыл бұрын
I got one that does same thing let me save yawl some drama next time it does that put your foot on the gas pedal press down then turn key it will work 90 percentage of time if don't work try it again thank me later
@lstruggy2 жыл бұрын
I had this issue w my 07 laredo I replaced my ignition switch ($40) and took me 30 min to install it and wala she starts right up!
@danielreynolds67643 жыл бұрын
I am having same problem with my daughter's 06 liberty i tried the ground wire to the relay and it still didn't help
@gonzohernandez97524 жыл бұрын
I did this today and nothing. I hear the same click when I try starting it. Help