2007-2013 Chevrolet Avalanche 5.3L V8 Throttle Body Replacement and Relearn

Рет қаралды 50,733

Жыл бұрын

This throttle body was used in multiple GM SUV/Trucks with the 4.2 Inline 6, the 5.3L V8 and the 6.2L V8 so this video should also apply to most GM SUV and trucks around 2007-2014
-Chevy Silverado,Tahoe,Suburban,trailblazer, and SSR
-Cadillac Escalade
-GMC Yukon,Sierra, Savanna, Envoy
-Hummer H1 & H2
-Saab 97X
-Buick Rainer
Throttle body Part #- Duralast TB1011D
throttle body gasket part- # Mahle G31974
AC Delco throttle body part #-12679524

Пікірлер: 49

@1ThomasBug Жыл бұрын

Excellent work on showing the printed instructions on the throttle body reset. That is what is needed for those who do not have a scan tool. Shows the DIYer that this can be done safely and correctly IF YOU FOLLOW THE INSTRUCTIONS. DGBryan

@steventappin8164 Жыл бұрын

Thank you

@brybrooks3648 3 ай бұрын

perfect

@oscarzavala7962 5 ай бұрын

My get the code po430 and the mechanic told me change the throttle body so what you think?

@terryraines9952 7 ай бұрын

thank you, I have the same truck and HAD that problem, but I got a can of Throttle Body cleaner and it helped, did you try that 1st?

@ms8510 Жыл бұрын

I have chevrolet camaro ss v8 will support?

@hardbodyty4866 7 ай бұрын

I replaced the throttle body but the car not starting

@b__l____o_____o___d2298 11 ай бұрын

U should have let us see how it ran before installing

@44hawk28 Жыл бұрын

Run at least two cans of carburetor cleaner through that intake, and then put a damn catch can on that engine. Those things should have at least a catch can , that or remove the that the PCV system works so it doesn't run through that intake and oil foul everything around it. I have built a few of these engines and found that General Motors Loves.030 gaps on these piston rings. That is ridiculously large. It sounds like they're getting a kickback from the oil companies to keep these things drinking oil. But at least with a catch can you can put a good portion of that oil back into your crankcase.

@armandomartinez6718 Жыл бұрын

You don’t need to disconnect the battery? Does your type of scanner allow you to disable the active fuel management (afm)?

@ultimatediyguy395 Жыл бұрын

No you do not need to disconnect the battery. It’s stupid that GM didn’t give users the option to turn off AFM. You’ll need to find a way to trick the ECU

@tomsadlink 10 ай бұрын

Use a Range, it plugs into the data port under the dash. It will keep the engine in V8 mode at all times.

@DAPHNE1776 Жыл бұрын

Can removing the air intake cause a need to relearn the throttle body sensor? Recently had to remove all of it to replace the lifters. 2013 Avalanche is idling like the engine will fall out and the only code is p0300. Replaced MAF, Spark plugs and wires, about to check the o2 sensor but i feel like im just nickel and diming myself to death.

@DAPHNE1776 Жыл бұрын

Also runs fine for about 30 seconds. I think it is the computer.

@ultimatediyguy395 Жыл бұрын

Doing lifters is a big job. Who knows what could be causing your problem. Did you remove the battery before tackling the job? Sometimes when throttle bodies are disconnected they need to be relearned give a shot and see what happens

@DAPHNE1776 Жыл бұрын

@@ultimatediyguy395 TYSM!!

@RedneckJesus513 8 ай бұрын

good vid, but of all the 30 billion brands you could have picked to use for the replacement, you went with quite possibly the WORST brand for electrical components. take the advice of someone who used to work at autozone, and dealt with their Duralast electrical components, and stay far away from duralast for electrical stuff. they're JUNK. i had to warranty out duralast electrical components at least 3 or 4 times a day when i worked at autozone. and most of the parts were only a couple months old. i strongly recommend going with either standard ignition, delphi, or acdelco.

@BruceWyn1 6 ай бұрын

Good advice

@MightyFlyChuck 10 ай бұрын

Umm did you post the pic if the procedure?

@ultimatediyguy395 10 ай бұрын

Yes at 6:18

@Hooligan357g 4 ай бұрын

If you at home you should of use instructions everyone doesn't have a programmer

@RaShaud 9 ай бұрын

Does this relearn process work on all gm cars I gotta 19 Malibu

@ultimatediyguy395 9 ай бұрын

More than likely no

@j.2391 2 ай бұрын

I got a 2010 chevy malibu p2135

@MrMexicanbaby123 Жыл бұрын

should I go get it reprogrammed at the dealership? Or will doing it the way the paper has it should be fine ?

@ultimatediyguy395 Жыл бұрын

Doing it the way the paper has it, is perfectly fine

@MrMexicanbaby123 Жыл бұрын

Thanks I’m doing this tonight on my Tahoe

@bowtieguy107 Жыл бұрын

Looking at your part #, thats not the one Auto Zone suggested for my 2013 1500

@ultimatediyguy395 Жыл бұрын

@@bowtieguy107 what engine is in your 1500? You could have the 4.3L V6 or the 4.8L V8

@bowtieguy107 Жыл бұрын

@@ultimatediyguy395 its the 5.3L

@jesusenriquez1673 5 ай бұрын

What model scanner is that?

@ultimatediyguy395 5 ай бұрын

Foxwell NT650 Elite

@jesusenriquez1673 5 ай бұрын

Thank you.

@RayTheFloofyBoi Жыл бұрын

Hey whats the scanner you have?

@Denverscorpio Жыл бұрын

It's almost $300

@ultimatediyguy395 Жыл бұрын

A Foxwell NT650 Elite

@keayremoore Жыл бұрын

Foxwell NT650 elite

@rustyshackelford7651 9 ай бұрын

Im seeing that one for $169. The more advanced "scanners" that can reset ECMs etc have come down in price quite a bit. I'm.seeing a few in the sub $150 range. I'm thinking Iay purchase one it would pay for itself in a couple uses. I work on cars a lot.