2007 Cadillac Escalade - P0011 Camshaft sprocket/oil pump

Рет қаралды 6,446

10 ай бұрын

Parts list for this job:
M365HV Melling oil pump
Melling oil pickup tube
Cam sprocket - GM genuine
Cam thrust plate - Melling
Timing chain - Melling
Timing chain tensioner - Melling
Oil pan pressure relief valve - GM genuine
Oil pan pressure relief valve deflector - GM genuine
Oil pan gasket
Water pump gaskets
Oil control valve - Melling
Also, sorry I mentioned the oil pickup tube is torqued at 106 ft lbs and that’s actually wrong, it’s 106 INCH POUNDS. Here is a link to the toque specifications I followed: ls1tech.com/forums/attachment...

Пікірлер: 48

@seanmarrero3461 6 ай бұрын

This was exactly what I needed to see. Thanks for this video

@pascalcoulanges6578 10 ай бұрын

Thank you this video was very useful.

@davntelisha19 9 ай бұрын

I have to do the same thing good stuff bro

@davntelisha19 27 күн бұрын

Yeah I’m pulling my motor out doing cam bearings rod bearing main bearing and also taking the motor to a machine shop I’m going all out I need my truck to last for a while just got new lifters I went with melling lifters and also went with comp cam cam shaft and better springs well hopefully everything goes well I’ll post here on KZfaq when I pull the motor out and show you the process

@rezcarguyz26 24 күн бұрын

@@davntelisha19 💯 sounds good 👍

@smacdiesel 2 ай бұрын

Cadillac should have provided a oil pressure gauge on the escalade.

@davntelisha19 27 күн бұрын

100 percent oil pressure gauge

@Lenoke85 5 ай бұрын

Melling makes a fork adapter for the oil pickup tube to have equal tension on the tube. I put one in my escalade. Chevy design fail allowing the o-ring to potentially bypass air, and that's not great for the internals.

@davntelisha19 9 ай бұрын

I think I want to change my cam too stock one while I do this job

@davntelisha19 3 ай бұрын

Do you still have the air ride hook up

@davntelisha19 9 ай бұрын

Dam 308 miles pretty good bro mines have 238

@illustr8phee100 7 ай бұрын

👍🏾👍🏾.. gave me Faith in my girl again

@philh9238 4 ай бұрын

Did it stall with the code? Mine warms up slow down idle goes down to 400 rpm then stalls becomes crank no start until it cools off

@michahoffman4148 4 ай бұрын

I got exact same problem as you lmk if you figure it out lol

@CameronNewland 2 ай бұрын

I have this problem as well. I heard the solution is to replace the camshaft position sensor and the camshaft adjuster magnet (and its gasket). Also should check wiring/continuity/resistance for related sensor wires. If you fix that and it doesn't fix your problem, then do a timing job, replace the oil pump, and do what the guys in this video did (replace oil pickup tube, clean out oil pan, etc). @michahoffman4148 @philh9238

@anatolyice4592 5 ай бұрын

Hello! What was the mileage of the car? At what mileage is it better to change the chain and pump? Do I have to change the lid to a new one?

@rezcarguyz26 5 ай бұрын

Around 300,000 miles. Depends how you drive and maintain the vehicle. You can change the timing chain anytime after 150K miles I’d say if you want to be safe. … change the lid?🤔 I don’t understand that question

@The_mechanic58 14 күн бұрын

Did you get the p0011 and stabilitrak and traction control??

@rezcarguyz26 13 күн бұрын

@@The_mechanic58 yes 👍, no light after doing this work.👌

@davntelisha19 9 ай бұрын

I seen this other guy on KZfaq he was getting the same codes we was getting po11 and traction light come on he put everything new like you did but he did new timing chain new oil pump new vvt sprocket new vvt bolt and oil pump just like you did and he said he drove it and he kept getting the code again then his next move was to replace cam bearings and cam and that was his fix

@rezcarguyz26 8 ай бұрын

Still running like a dream. So far I put about 5000 miles on it since the timing overhaul 👌👍

@rezcarguyz26 8 ай бұрын

Haven’t seen a code yet. The traction light blipped a few times, actually twice ✌️ which could’ve been from other factors, other than that she’s been running great.💯💯👍

@LovenotHate130 2 ай бұрын

I did everything also my next move is new engine or cam bearings and cam shaft

@davntelisha19 27 күн бұрын

How she doing she still running great no traction light again

@rezcarguyz26 27 күн бұрын

@@davntelisha19 still running great, no traction light, great oil pressure 24-27 psi on idle. I’ve put about 10,000 miles on it since the video. ..

@The_mechanic58 20 күн бұрын

Has the stabilitrak and traction control and p0011 code come back on ?

@rezcarguyz26 13 күн бұрын

@@The_mechanic58 no. The truck has been running great since I’ve changed all these parts.

@rezcarguyz26 13 күн бұрын

@@The_mechanic58 the truck has around 323,000 miles on it 😄👌

@davntelisha19 3 ай бұрын

So the issue was the oil pump o ring after all right

@rezcarguyz26 3 ай бұрын

Yes 👍

@user-uk3fd7jj1n 10 ай бұрын

لم يفتح هذا الفيديو

@davntelisha19 6 ай бұрын

Did that traction light come on every time and sometimes cut off by itself or 2 times a day

@rezcarguyz26 6 ай бұрын

Before I did all this work to it yes, the truck was throwing STABILITRAK codes intermittently.. after I completed all this work the truck has been running like new ever since. One thing I’ll recommend for the 6.2 LS is to use WIX XP oil filters. If I’m not mistaken I’m pretty sure the WIX XP filters were engineered to run with the GM LS engines because of the lower idle oil pressure.. the pressure relief valve in the WIX XP filters is a lower setting than other oil filters like Purolator boss that’s set around 22psi. Truck runs noticeably better when I run WIX XP oil filters and now that’s all I run 👌👍

@The_mechanic58 Ай бұрын

What scanner is that

@rezcarguyz26 Ай бұрын

Thinkscan SR1

@davntelisha19 3 ай бұрын

How she running no more po11

@rezcarguyz26 3 ай бұрын

Running awesome 👍

@keysautorepair6038 Ай бұрын

If you change all the stuff and it doesn’t fix it, I know exactly what it is ask me and I’ll tell you I had the same issue changed everyone of these pieces with all GM parts and none of it fixed the pressure issue no it isn’t the camshaft bearings either.

@rezcarguyz26 28 күн бұрын

After changing all these things I’ve put about another 10,000 miles on it as it is my daily driver and 30 minute trip each way and the truck is still holding up. What did you change?

@keysautorepair6038 28 күн бұрын

@@rezcarguyz26 Was the lower intake manifold gasket o rings bleeding oil pressure after changing everything else I was thinking it might be the camshaft bearings glad I didn’t change them and tried the intake gasket first.

@rezcarguyz26 27 күн бұрын

@@keysautorepair6038 awesome 👏, is your truck VLOM?🤔

@annettegonzales168 27 күн бұрын

We have the P0011 code coming up again after changing the cam shaft the solenoid and positioning sensor. I’m at a loss. Any ideas? (07 Yukon Denali 6.2) also the oil pressure gauge is at 0.

@keysautorepair6038 27 күн бұрын

@@rezcarguyz26 2007 gmc Yukon Denali 6.2.