Added a little extra stuff with this one. I replaced the filter and cleaned up the surfaces at the end of the video.
Пікірлер: 24
@MyPlayez Жыл бұрын
I got ripped off by some shady mechanic replacing mine for me for 3600 dollars, he took over 3 months to fix mines and it only lasted me for about 6 months before it messed up again😕. Now im going to try to fix it myself. Thank you for this video 🙏🏼
@CarMechaNick Жыл бұрын
That stinks? Hope you’ve gotten it sorted.
@luismartinezz8936 Жыл бұрын
Thanks for vídeo Im taking mines out to fix it and it’s my project van,the sad part of this vehicle that there’s not many videos about them on KZfaq and is hard to find accessories for them
@luismartinezz8936 Жыл бұрын
And should i buy a new cooler for the transmission?
@robwillard3453 Жыл бұрын
@@luismartinezz8936 Yes these overheat very easily
@luismartinezz8936 Жыл бұрын
@@robwillard3453 thanks, people have told me that these mini vans suffer from transmission heating issues, they gonna repair it this week so im buying a new cooler
@robwillard3453 Жыл бұрын
@@luismartinezz8936 yes, a mechanic tried to sell me a new transmission but it was just the saddle and cooler. It slipped from 3 to 4 gear after around 30 minutes of driving.
@CarMechaNick Жыл бұрын
Hope it’s working well for you!
@josephdoe94076 ай бұрын
Where do I get those plugs for the lines and what are they called
@chrisolson64444 ай бұрын
Help. 2006 mazda 5, i got the transmission installed and when into tighten the trans ti engine bolts i can bearly trun the engine over.
@gregenera2825 Жыл бұрын
Did you ever tighten down the nuts from the torque converter to the flywheel? It seems when I do so it pulls the torque converter out of the transmission and leaks.... Any idea how to fix it, maybe a washer?
@CarMechaNick Жыл бұрын
No way don’t try to customize it. You either have the wrong part or a bad seal. It should come towards the engine SLIGHTLY but shouldn’t leak. Sorry to hear that.
@mrmusclecarsuspect53622 жыл бұрын
Do you find it posible removing the transmission with torque convertor left on flywheel? I did and installed it back.with convertor still on the engine. A little space but made it work! Great video
@CarMechaNick2 жыл бұрын
Definitely possible, just have to be gentle. What a job!
@groovymoon10 ай бұрын
Nice. Total time?
@carlosbanegas7577 Жыл бұрын
thank you very much
@CarMechaNick Жыл бұрын
You are welcome, thank you! 😊
@camerongates91972 жыл бұрын
Is this possible with 6 inch car ramps?
@camerongates91972 жыл бұрын
And do you have to lower the engine?
@CarMechaNick2 жыл бұрын
I would rather have the car propped high on jack stands. After you disconnect everything up top, to avoid tippy toes. You'll need to support the engine when you separate the two.
@25111Ashley2 жыл бұрын
how long did this take
@CarMechaNick2 жыл бұрын
Not long at all, maybe 5 hours. That doesn't mean you'll only be charged for 5 hours though. But I don't think it calls for more than 7 or 8 hours book time.
@shinigomie23582 жыл бұрын
I didn't see him remove the subframe
@CarMechaNick2 жыл бұрын
That's because I didn't remove it. It's a partial subframe, I only ever need to remove full subframes.