Car MechaNick

Пікірлер

@Chris-mp3tq Күн бұрын

How many labor hours 😢

@delosangeleshernandez-w1h 13 күн бұрын

gracias exelente video fue de mucha informacion y muchos detalles

@lesklower7281 18 күн бұрын

I have no sound but l can see why you are replacing this 2015 Hyundai engine how horrible are Kias and Hyundai's there are so many you tube videos to do with Hyundai and Kia engines none of them good they absolute piles of junk well my 1997 Toyota Hilux with 437000 kilometres on it is perfectly fine and probably will never have to be replaced at least for another 27 years

@user-gd6cz5ms5f 18 күн бұрын

Sir thank you very much for this video I didn’t know how to access the bolts that on the flex plate

@user-gd6cz5ms5f 19 күн бұрын

How did you remove the transmission from the engine

@nickcruz2389 23 күн бұрын

Hey I know this is an old post but I had at question. At -23:10 minutes, what is that cable you are pulling out from the top? Looks like you just use a screwdriver to unhook it

@nickcruz2389 23 күн бұрын

11:36 seconds into the video

@gellishustle500 Ай бұрын

What is the best battery ratchet to use

@pardeepSingh-cu9dm Ай бұрын

👍👍👍👍

@Lawgive1234 Ай бұрын

Great and excellent video 💪🏾👍🏽

@kubeanie18 Ай бұрын

service that ptu lol

@bodini315 Ай бұрын

Are 2013 and 2016 similar in this process are there any major differences that you are aware of?

@kassies2832 Ай бұрын

My 2013 altima is at AAMCO right now getting the transmission replaced. Now i know why it is so expensive. Thanks

@augustomejia Ай бұрын

Just straight to the point video no talking,

@fordford3338 Ай бұрын

Is there better way to lift it up from top ?

@user-ci9yg9lf7n 26 күн бұрын

Did you have to program the pcm to the new transmission?

@CarlosHernandez-tj2og Ай бұрын

I was wondering if this is the same as a 2018 Ford Fusion 2.5?

@JuanHernandez-un7gr Ай бұрын

Can a 5.7 l small replace the 2.0 engine in these cars?

@tim37471 2 ай бұрын

Did you have to unbolt the torque converter before pulling the motor

@426TUNES 2 ай бұрын

Great Video. Do you have to pull the exhaust system?

@erocker78 2 ай бұрын

Hi, I'm just curious. What part of Ohio are you in? Do you work on Toyota's?

@thebestofmasters 2 ай бұрын

how do you remember where all the screws go?

@zafar78600 2 ай бұрын

I think, just buy a new car.The time u spend in dismantling, then repairing, then re installing, do u even make minimum wage?

@brandonzimmerman9158 2 ай бұрын

It’s been 4 years, I understand. But however, I’m in the middle of an engine replacement in a 2015 Durango with the 3.6. New engine is in, but I can’t get the torque converter to spin around freely to line up with the flex plate bolt holes. Did you have this problem?

@SINRYTUBE 2 ай бұрын

Where are you from?

@sigtech_gaming 2 ай бұрын

I didn't see an engine bar holding up the engine or a jack below. I also only saw onr motor mount. How is this engine hanging? Lol

@craigherron7696 2 ай бұрын

Just found out my transmission is going to need replacement. How many book hours should i expect it to take?

@afranklin5670 3 ай бұрын

What state are u in?

@ladyt_speaks_truths3923 3 ай бұрын

What are all of the major parts you had to remove in order to remove the engine? Btw love the video but I wish you could have mentioned each step as you worked

@jeremyford7278 3 ай бұрын

How many bellhouse bolts should it be

@toddmuehling2818 3 ай бұрын

What’s the star socket called? And what size is it?

@Alpha1258 3 ай бұрын

I this time lapsed ??? 39 mins. Is AWESOME !!!

@denisboss7309 3 ай бұрын

Is there a difference between a transmission with a plastic valve body pan and a metal valve body pan? Will a transmission with a plastic body pan fit a hyundai that had a metal body pan?

@BraydenTaves 3 ай бұрын

That fuckin Matco puts in work gawd damn

@chrisolson6444 3 ай бұрын

Help. 2006 mazda 5, i got the transmission installed and when into tighten the trans ti engine bolts i can bearly trun the engine over.

@Surfer_Dude858 3 ай бұрын

I'm getting this done right now to my car had 130,000 miles on it and the only reason why they're doing it for free is because I got all oil changes done the dealership

@oralwayne7273 3 ай бұрын

CAN I REPLACE A 4 cylinder EQUINOX with a V6 ENGINE?

@kaferere 3 ай бұрын

You don't need to take the drive shafts out of the Hubs at all nor remove the Hub nuts. For the drive shaft that's in two halves, separate the halves at the bearing support bracket BEFORE you remove it by tapping with a block of wood and a hammer. Take the halfshaft off the spline and leave it in the Hub, tuck it in the wheel arch out of your way, then remove the bearing support bracket complete with the other halfshaft, For the other side driveshaft. once the lower ball joint is undone, there's plenty of play in the suspension leg to take the driveshaft out of the transmission, and tuck it out of the way completely. Messing about removing the driveshafts from the hubs, hoping they're not seized is unnecessary and adds anywhere from 20 minutes to a whole day to the job, depending if they're seized in the hubs or not. No need to touch them.