I know how to change cylinder head gaskets, But got to say this is one of the most informative and clear videos I've seen on any vehicle repair video on KZfaq. Excellent job fellas.

Best mechanical repair video I have seen. The method of showing what has to be removed then forwarding to show it removed is perfect. I followed your video instructions on how to do a Prius head gasket and then dove into my 2010 Prius last fall; it went well. Now the 4.0L caravan has a blown gasket. Your videos are golden. Think it's time for me to donate :).

The setup on the 3.3 is almost identical to the 3.8, just used this to get my head gaskets done. Thanks for the video!

Thank you. You just convinced me to keep my 2008 van. I don’t have much to lose at this point.

Awesome instructional video! Top notch in every aspect and very informative with good commentary. Well done!

You make it look so easy. I've been very intimidated to replace some gaskets, this was extremely helpful

This is the best quality repair vid I have ever laid ayes on! Thank you!

Man awesome video. Couldn’t have been done any better. Appreciate people like you

Great job, I would have changed the oil too after that job before starting the engine. It's possible coolant mixed in with the oil. I also would put the car into clear flood mode and crank several times to flow the oil prior to ignition.

Excellent job just guys very well explained and great video!!

That's a nice trick with just moving the rear exhaust manifold out of the way to get to the head bolts! I've been struggling trying to detatch it from the cat...the four corroded bolts are stuck on there pretty tight.

Cylinder 5 in mine was showing on the plug. Thank you so much for this video, having an expedition (5.4 turd on motor number 2, cam bearing cylinder 3) I was relieved to see how flippin easy this was for the wife's gc. Subscribed!

Me subieron el ánimo, hace muy poco compré una chrysler town country, creyendo que había comprado un problemon y me doy cuenta que mecánicamente son muy simples.

These guys are real mechanics!

Bad ass quick and to the point explanation and alternatives to take during this process

Thanks for the video! Don't forget to clean top of the block before slappin the new head gaskets on there

My 3.8l is one of those that uses 2 quarts oil between changes. Planning to remove heads and oil pan to rering the engine. Also have heads rebuilt with new valve guides and seals.

❤this was soooooo helpful and it's exactly what is going on with my van

Awesome video, nice, clean, and concise, thanks guys!

My 3.8l has what looks like an external head gasket leak. When I replace it will I need to do both heads or can I just do the bad head?

Thanks so much, this will be my next project in my T&C. 3.8

Great video. This year van has tons of room it looks like.

Thanks guys this video was really helpful. I am working on a 3.8 not much different thank you.

Seriously, thank you! Blessings!

Thank you and thank u two toes

Gracias me sirvió de mucho sigan subiendo más videos saludos de un mecánico de Perú.

Thanks for uploading this video you guys just gave me confidence to take my 3.8 liter motor apart which is same exact set up. Would you recommend removing the heads for a cross threaded spark plug hole on cylinder 3? I purchased a spark plug thread chaser but I read that while using it, metal shavings will fall inside cylinder hole and cause internal damage.

Greate job you are the best!

I HAVE THE SAME VAN AND IT HAS 2100000 MILES AN STILL GOING AND IT JUST PASS SMOG CHECK ‼️

Great video, I'm about to try and fix my wife's 2004. One question tho, you didn't seem to bother matching the push rods to where they sat. Most mechanics put them in order on a piece of cardboard. Is it something with these engines and sloppy tolerances and/or hydraulic lifters that make that unnecessary?

Nice video, I might have to change my. Thanks

THE BEST ... ABOUT TO TACKLE.

Awesome job. Thanks guys

Great video sir

Does this apply to the Chrysler Grand Voyaher 2007? The engine looks fairly simullar.

Replacing the PS fluid with ATF +4 per Chrysler’s recommendation will quiet that PS pump right down.

Thanks so much for the video

Good instruction video. Would the same steps as in this video apply to a 3.8 L, v 6 in a 2008 Dodge Grand Caravan? When putting both heads back is there is anything to watch out for, or to be super careful? Do you have another video of putting the heads back on?

Great job! thanks

Watching this video as I get ready to do head gaskets on a 13’ with 580,000 miles.

Thank you

These engines would make for a fun custom sports car build/conversion. Not blisteringly fast or anything, but if it didn't have to carry a van and got some basic mods....

عمل ممتاز شكرا لكم 👍🏼🌼💯

Any tips on the 15 mm lifter bolts? I've sprayed several times and I can't get them off. Impact and everything.

Do u u have to take off more things if u have a 2007 dodge caravan 3.3? My altenator is lower than the one u guys r working on here. Great video but wish u would b slower and explain things more.

I wish u would have shown taking out the rear bolts

Got my head off from you help my question would be if the valves should all be closed when off I have one open and I’m sure that is my running issue

Хорошая работа. Спасибо.

I watched all the videos

I have 3.3 liter 08 same one you're working on. 91,000 miles it's spitting and sputtering but no engine light. Help

Could you help me out? I have that minivan, 3.3, 2010 Flexfuel. While driving on the highway uphill a strong metallic noise started coming from the motor (about 38 miles from the starting point). I still drove, in those conditions, over 250 km. The mechanic says that the motor is 100% gone and that the repair will be over 1,000 USD (I'm in Mexico). Is it possible that the damage is located exclusively in the crankshaft and bearing metals?

Can a head gasket cause a misfire on a specific cylinder.?

Wate till you try and remove the trans. way to many brackets, a big pain.

Would this tutorial work for a 2004 Chrysler Town & Country? I heard they are very similar. Mines a 3.8 litre v6 though.

What about the timing chain/belt?

I had to do the front head gasket to set one of the pushrods that came undone. Once we put everything back together, my van wouldn't start. It cranks, but no start. Tried to bypass the fuel pump relay using a wire, but still no luck. No fuel coming out from the fuel line. What are the changes that the fuel pump went bad at the same time? Any suggestion what could it be the cause of it? Mine is also 2008 grand caravan. Does this van have inertia or shut off mode? Thanks in advance

is for the 3.8 engine the same thing? 2005

can you reuse the TTY headbolts?

How much do you guys charge to do the head gaskets? I've got an 05 Town & Country with a 3.3, I just bought it a week ago, only has 120,000 Mi on it, the guy I bought it from was a shyster, radiator is full of head gasket repair dope, no water in the oil, OR out the exhaust, but it's pushing out the overflow, must be blown between cylinders

Excellent video guys. Question 1: Was the head leaking oil (reason for head gasket replacement) or just because of mileage? Question 2: You mentioned having the heads machined. Is that a typical practice when head gaskets are being replaced? How long did you have to wait for the heads to be ready for you. Thanks from Vancouver, Canada.

what torque is it for the intake bolts

Thanks for the video. The plastic Y pipe on my 2010 DGC with a 3.3 decided to split and dumped all my coolant. It overheated and now I have a misfire on cylinder 3. I know my head more than likely warped and will need to be repaired by a machine shop. Anything else I need to think about? My skilll level is advanced DIY. Thanks.

Change that can check fuel injection manifold leak catalytic converter it's like renew the car but not the transmission that's another invest

So for that job on that Dodge Caravan how much should I pay the mechanic

Hi I own a Dodge Caravan with a 3.8 engine size The car suffers from such fuel exchange 40 liters of gasoline travel only 100 km The engine is in good condition The nipple sensor is on and it has been tested The nozzles (fuel spray) have been replaced with original quality Currently only there is a p0325 code Does this sensor increase fuel exchange? what should I do

Is that all for the intake gasket the metal

My mom bought one that likes to over heat 3 radiators 2 water pumps 3 thermostats. Have no clue how much coolant. And it keeps over heating. We did a vapor block test and not getting the color change. Need someone to have a tip.

So I just finished replacing the upper and lower manifold gaskets on my 05 as well as the valve cover gaskets...If I had gone all the way and took the heads off, they HAVE to be reground ? You can't just remove them, change the gasket and put them back right ? I know I sound stupid but I'm not a mechanic, I just knew I could save 5k in labor with the work I've already performed...the engine doesn't seem to be leaking from the head gasket anyway, was just curious..thx.

My 08 dodge grand caravan 3.3 liter it has 71, 000 miles and hesitation and jerks when giving gas , do you know what causes that?

thank you very much for this nice video . can you please tell me the torque specification for the head bolts how many ft lbs i think you said they are 8 bolts. thank you

So when taking off the head, it's actually 8 bolts per side?

did you replace the head bolts and how do you like that earthquake ratchet

What's the amount of time spent doing this task? Got a 2010 DGC and I am usually on-call 24/7/365... but I can schedule upto 8hrs off if need be...

Oh and mine is a 2015 Dodge Gr. Caravan

I change my head gasket on my 2001 Chrysler town and country but I hear a small tapping on the back cylinder head. I feel the lifters is stuck so do I have to remove the cylinder head to change the lifters

Fords are crap🤣🤣🤣🤣! Great commentary during the video enjoyed working on my Caravan,thanks

What’s the torque spec on the intake?

This not use timing belt, how is the cylinder position?

Probably won't get anybody to respond. but I got a gr caravan in shop they've had it for a wk. Said it had leck at head and still wont fix it. They keep saying need to know why guess of leck. So that extended warranty will cover fix. Any advice. Oh and at some point said it was cylinder 1

Thats the mileage I have on my '07 3.8

It has been a while since I last did a head-gasket replacement. Would the tappets require readjustment after 0.011 were milled off the head or do these newer engines adjust for that automatically?

Hello from the leaning tower of Pisa, can you tell me where to buy the head gaskets for my 3.3 L Grand Voyager online? From Germany only the valve cover gaskets cost €58 each plus shipping, they probably cost less in the USA but above all I'm interested in having the ones you used for the cylinder heads, my car is from 2008.

Not a mechanic but I'm tempted to go try to fix my 2008 Dodge Grand Caravan. I'm having this same problem.

How do I replace the oxygen sensor

Great job, I have a cuestión, Did you put the engine on time before you disarmed everything?

Do you still have that? I cracked my windshield. Would love to buy it off you.

Well you made it look easy want to send you ten dollars how?

How much a job like this cost

Is that the same for 2004 Dodge Grand Caravan

Hello Gasket Masters, Great videos any chance you have on of a 3.6L Dodge Grand Caravan 11-20?

Hey guys great video can you tell me if it's the same to do the 2009 4.0 liter engine question mark

This is how I take the whole engine out the top... Way lots easier. You can damn near get two guy to just lift it out... Just to add. Dodge adding that Accessory bracket on the front of the engine. To hold all their pulley, alternator and PS pump was genius.. As taking that plate off is even easy....If you ever do a Oil pump and timing chain....

I just finished mine and when I started it it was smoking out of the exhaust manafold. What on earth did I do wrong?

Looking for same on a 3.8L engine... is it the exact same procedure? Assume largely the same... but gotta be careful with assumptions.

wow these engines really are stupid easy, modern Chrysler engines are just as complicated as ford if not more. with the hurricane engine I'm talking about all that for 1 MPG better over a v8 hemi 🤣

no exhaust gaskets?

I’m sure I’ll be ridiculed for this but I had a coolant leak coming from the radiator and water pump. I had just been topping it off with water until I could get the time to mess with it. We had an unseasonably cold night in Nov and I think the water may have froze inside the cooling system. What’s the chance I cracked the block or cylinder head? I know the van overheated the next day. When I noticed it I limped it home about 3 miles and parked it. My coolant is definitely going somewhere still. I changed the water pump, thermostat, lower radiator hose, coolant temp sensor, and radiator. I don’t see any white smoke coming from the exhaust. Oil looks like straight oil. No leaks on the driveway. Could it just be the head gasket?

45 65 then 90°

Dude you sound like mayhem the fighter

Hi, whom do you send the parts too, to have them checnked?