You’re scaring me to death by not covering up the intake holes. That’s the most important part of the job. I truly admire your mechanical skills.

You don't have to split the manifold in half to take it off. The throttle body should be removed first, then the bolts for the manifold. Also the hoses on the TB don't have to removed. Other than that great vid!

THANK YOU. I pride myself in being able to figure out my own work on my car but this was something I was skeptical to attempt solo. This was a great guide.

So... you. are. amazing. and I wish I had a garage... but you just convinced me this is worth the money to have the mechanic do for me :P

Reducing the size of the spark plug tube seals by placing them in the freezer is a brilliant idea! I'm glad I saw this video before I did the valve adjustment on my TL. Thanks for the tip!

You did an absolutely amazing job with this. I just bought a used 2014 Honda Accord V6 Sedan Touring model, I brought it into Honda for a timing belt replacement along with the tensioner and water pump. After they made their usual 24 point inspection, they mentioned it has a valve cover gasket leak. Luckily I did purchase a 5 year and additional 95k warranty for the car that covers every part of engine and transmission minus wear items. They told me it would of been an $680 dollar job for them to do it, so I was thankful it was covered. I am somewhat mechanically inclined, but this a bit more than I'm normally accustomed to doing. So again just wanted to see that was might impressive work you did right there! 👏

Thank you, thank you, thank you. I thought I was gonna replace the valve cover gasket of my 09 Honda Accord V6 myself until I watched your video. I think I'll pay one of my mechanics to do the work. I'll check back for other videos. Thanks again and it's great to have a female mechanic who knows this car. How cute!

I can't believe a GIRL made this kudos to you 👏 I need this done and I'm stressed about how much it cost but it's alot of wk I see and u gotta have the right tools 😮😢

great job very informative. Things like the vacuum lines and fuel lines can be just unbolted and cast to the side inside of disassembling them makes it easier to install same for the throttle body just unbolt it from the manafold and also never use metal to scrap rtv there’s always a chance that you can scratch the surface and oil will leak from there use a plastic scrapper as steel will scratch aluminum and plastic won’t. those dental pics are great for removing the spark plug gaskets make sure to torque down the valve covers and the intake in a crisscross pattern so it can be seated evenly

It's about time Little! Great job very informative.

Wow! What a beautiful woman doing a job that I would have liked to be there with you to help you and at the same time learn, since my Accord is the same 3.5l but 2009. I love what happened to your little helping hand, every second I watched you and listened to you. You are a very cautious woman, with bags and labels so that the pieces don't get lost... I do that too, but obviously your handwriting is much prettier haha... Anyway: it's been three years since you made that video and it's a shame that I'm barely seeing you. I wish you a very happy life, that you have good health, big smiles, love in your environment and that rubber mallet so that you no longer struggle to take care of the delicate pieces. A hug beautiful woman.

I’m very impressed. Great video. Showing these dudes what’s up.

Hey Miss Reed great vid, really helped refresh my memory ...keep it up✌

Great video. Give you props for working on the side of a busy street like that. Be careful when you’re removing things with a screw driver as you may run into the chance of “stabbing the shit out of urself”. You must’ve went to school for automotive you seem to know your parts. Keep it up!

Awesome video thanks for sharing.. learned a lot from this video 👍🏼

I really liked how you did start to end, Thank you very much, keep doing more video

Does anyone know what that section to the left of the bottom valve cover is? It's got 5 bolts. 1 below the oil dipstick, and 2 bolts below the blue connector in a diamond formation. 21:34 . I wouldn't remove the coolant hoses either, now that I know where they ARE! lol, I have to see videos with some mistakes, and this engine type was the closest to my engine configuration. I'm the guy that has to watch 50 videos of the same thing before I actually do....my first valve job ever. Great vid!

What a Great Video You have Shared. Thank a You for sharing your Knowledge and also good Camera Work and editing! ✨✨✌️

Someone needs a rubber mallet for Christmas

I'm about to do this and your video sure will help a lot. Also, I'm impressed that you did it mostly using common hand tools. Hope you will continue to make more videos about this car.

Impressive. Well done!

Wow this videos it’s sooo good ! Thanks

In conclusion, I’m calling my mechanic to do this 👍🏼

Very helpful video needed this.

Great job!

nice! i need this steps so i can change my VVT.

Be careful unclipping the coils those little tabs can snap really easily. Thanks for the video X

Can I just fly you out to Cali so you can do this for me. Lol. Great job

Great video! We bought a 2009 Accord V6 and the front valve cover is leaking like crazy. Have you posted a link with the valve cover gasket?

You are amazing!

The HPS air intake hose you are using, what is the part number? I too want to use the OEM air box. Thanks 😊

a seal removal tool works wanders on the spark plug tube seals!

Good job girl

You're awesome

Hello, thanks for the video. Say... how long does it take to do this job? and how much would you say is fair to pay.

Where did u find the gasket at 12:18 I legit can’t find what the gasket name is called in between the intake manifold when she separates the two pieces at the time I put

do you have the part number ? also, is it two gaskets? one on the front and the other one on the back ?

Let's see more videos.

Is this where the oil is leaking onto the car's alternator? My alternator stop working cause oil was leaking onto it I just don't know where from. I have a Honda Accord v6 2008

Does this job apply to a 2012 V6 honda accord

I had a shop adjust my valves and they didn’t put the gasket back on right and it’s been leaking oil ever since and they’re not takin responsibility for it. Thinkin about doing it myself until I seen this video. Why’d I think t was gonna b easy. Lol

Anyone have an issue with the back valve cover removal because of the wire harness that’s overtop it? Been rackin my brain here tryin to figure out how to pull this thing without having to take the wires out of the plastic harness lol

This is a really tough job Honda charge $850 just to fix it 😒 🙃

8