A couple of helpful tips, when replacing my speakers. I couldn't get the clips loose for the door latch. So I put a small calapsable table under the door panel to hold it up while I replaced the speakers. I didn't have a 5.5mm socket for the speaker screws, but a 7/32 quarter inch drive socket works well too. Good luck with your speaker change out.👍👍👍👍😎😎😎
@redonKiLaus2 ай бұрын
Thanks for watching!
@Night_Thunder2 жыл бұрын
If you want see hug change you must edit EQ by forscan ,, your mid and low bass will come back
@jonmichael29 Жыл бұрын
What settings do you make in forscan that will improve the sound? I would like to do this to mine. Thanks
@dmoney2530 Жыл бұрын
dont need to get bass out of your doors when you have 2 12s
@JPandher9 ай бұрын
@@dmoney2530why have a backseat wh en you can have 2 12’s. There is no reason why you would need more bass than door speakers can provide.
@drophammer7766 ай бұрын
@@JPandherHe can't hear you.
@jamesbennett84026 ай бұрын
Holy shit, this comment should be mandatory on all the ford speakers swap videos. Thank you
@cameronjacobs9697 Жыл бұрын
Did the Metra adapters fit your speakers easily? The Metra adapter disconnects won’t fit the terminals on my Punch speakers
@redonKiLaus Жыл бұрын
The pins needed to bend ever so slightly on the factory connector side, but on the speakers themselves, no issues. Thanks for watching!
@tonyfoley9988 Жыл бұрын
What's the part # for those speaker plug/cable? I'd like to have the adapter plugs but not the speakers and definitely not from Stage 3, there way to expensive.
@cameronjacobs9697 Жыл бұрын
Metra 72-5600, hope they work for you, the disconnects are too small for the Punch speakers I bought
@reinaldonieves1964 Жыл бұрын
You didn’t show us the quality on how they sound👎🏻👎🏻👎🏻👎🏻👎🏻👎🏻👎🏻
@redonKiLaus Жыл бұрын
That wouldn't come thru a video - too subjective with a microphone capturing speaker output, KZfaq audio compression, and folks listening with different speakers. Thanks for watching!
@briang15612 ай бұрын
These speakers are better than Sony?
@redonKiLaus2 ай бұрын
They're about the same, my original ones were completely blown so they needed replacement badly. Thanks for watching!
@ryanguidus45232 жыл бұрын
Can you link the speakers you bought and the adapter you used as well?
@redonKiLaus2 жыл бұрын
Link is in the description. Thanks for watching!
@dossman10003 ай бұрын
hows the rattle?
@redonKiLaus2 ай бұрын
No rattle at all! Thanks for watching!
@TheCourage2Combust Жыл бұрын
Why do you take the whole door panel off
@redonKiLaus Жыл бұрын
No way that I know of to access the speaker otherwise. Thanks for watching!
@robertsmithUH60driver2 жыл бұрын
Do they sound better?
@redonKiLaus2 жыл бұрын
Far better than the blown Sony ones. When I bought my truck the speakers were already toast so I can't comment on comparison to stock, but I'm guessing better...to what degree I don't know. Thanks for watching!
@robertsmithUH60driver2 жыл бұрын
@@redonKiLaus I bought my truck new and thought the skny upgrade stunk from the start. Need to add sound control also. Thanks for the reply.
@Fence-Dogs-More2 жыл бұрын
Kickers were garbage in my f-150, sounded like a can and no bass. I put the nice $130 JBLs 6x8
@VeritasIncrebresco Жыл бұрын
Did you need an amp?
@DeerslayerMike4433 Жыл бұрын
How much did you pay for your speakers? I will do the same replacement for my truck and paid $50. or so. Just curious if yours are much better than the original ford factory speakers.
@redonKiLaus Жыл бұрын
I think it was a bit over $100, can't remember at this point. Thanks for watching!
@Badenhawk8 ай бұрын
What if the previous owner was an idiot and snipped off the factory harness and just twisted wires together with electrical tape like a meth head? Lol, jk, ill just have to use the supplied wiring to twist and shrink tube it on I guess. Thanks for the tutorial.
@dylanperkins14608 ай бұрын
I feel attacked 🤣🤣🤣 I was young and dumb
@Badenhawk8 ай бұрын
@@dylanperkins1460 so, my story continues. I opened the driver's side door first because that speaker was blown, found the janky wiring with an aftermarket JBL speaker. My mistake was that I then assumed all 4 door speakers were done the same way. Nope, the other 3 were all factory speakers with the harness still intact, so I guess I will have to use this tutorial haha!