www.williamsmobileclutch.co.uk 🇬🇧 Contact us for your clutch replacements. Thanks to all our subscribers and viewers of the channel. 🎉

Thanks man I'm a 65 year old cancer patient I watched your video and it inspired me to have a go at my own V50 so clear you are a very efficient worker good on you regards Vince

Kevin, I changed my clutch and DMF over the weekend using the Haynes manual and this video. This video was is worth its weight in gold, it was by far more useful than the Haynes manual and was the reason I was able to complete the job. It took me 2 days to finish - I'm in awe that you do this as your day job, and film it and complete the job in 4 hours, unbelievable. Thank you so much sir!

This guy is like superman or something, how easy he makes it look to put back the gearbox, I'm in awe!😮 Took me a chain to an engine jack over the car to first raise the gearbox upclose, then about 2381 tries before it connected properly. Man you are a god!

Thank you. I was able to replace the flywheel and clutch (and CV axle, while I was at it) on my 2005 V50 2.0d with the help of this video alone. Cheers! 🍻🙂

excellent video - exemplary for all KZfaqrs... thank you so much

With the help of your videos i did my first clutch on a 2013 Citroen C3 , turned out it wasn't just the clutch it was also the gearbox so it was a gearbox of times 2 :)))) , them did a 2002 Nissan Primestar again watched one of your videos on the Vivaro but this one was the 1,9 so had some differences but still not fun at all :))) I just wanted to say thank you for doing this videos it shows that with methodical work even a person like me who by profession is a registered nurse can tackle the job.

Nice work as always Kevin 😊

Excellent work, not so easy to work on the Volvo. 👍

Super great work. I love your style of work. Very much respect from Japan. Please be careful for eyes.

Amazing job. Thanks for sharing this great video.

Estupendo trabajo y muy buen video. ❤

Good job.I'm sending greetings from Poland

A murky morning for you and it looks as though that Volvo could do with some new suspension on it thanks for the video stay safe

Badass move just hoisting it up by hand

Great job!!👍

That was amazing😮 I have the same V50, it's all so tight/compressed, not much space to work.

Zajebiście:)

Great job.which this guy was my neighbour

Greetings from Poland !

Thnak you , i will try this

Top👌👍 Grüsse aus Düsseldorf 🇩🇪

Guilherme um mestre

Volvo is a little harder to work with, but once you know how to do it, it's only a matter of time! good job!

thank you

Have you done a 2013 V40 D4 yet? I particularly enjoyed the ball joint pinch bolts that seize into the alloy hubs...

Hai fatto un lavoro eccezionale,sia come meccanica che come ripresa cinematografica,in condizioni difficili.I miei complimenti.Permettiminuna domanda,che pasta è quella rossa che dai su alberino e sede delle viti? grazie

Mr. Kevin, in which gear of the milwaukee impact wrench are you tightening the wheel hub (the big screw)

Not all heroes wear capes 🫡

Hi kevin ! I'm from Sweden so I'm not very good at English so I'll give you a disc via Google translate, I'm going to change the clutch on a Volvo 2.0 diesel -08 the same job as you do in the movie, here in Sweden it's mentioned that you need a special tool to clamp the release with but I have the same tool you have to center the release with, so wondering is it just to clamp the pressure plate crosswise? Very good videos you make, I also watched when you changed a Ford Fusien 1.6l and it was very helpful.

When you're working on the older vehicles Kevin, how do you cope with the rust and road dirt dropping into your eyes? Every time I'm under my old Forester I wear safety specs, as it always manages to drop a load on to me.

At a typical garage, what cost would I be looking at for a clutch replacement including labour do you know?

🧘. I finish my session and I watch 😂😂

33:23 me in a Cessna 🛩️👋🏻

Hi Kevin what's your thoughts on a solid flywheel conversion? Do you think it is too harsh on the gearbox and poor driving experience?

Çok iyi

Great video and attention to detail. What is the black paste you put on the back of the slave/throw out bearing. Is that a gasket sealant? Keep up the good work

Hi mr Stig Kev, did uou learn your trade in a main dealer/independent? What made you decide to do clutches instead of general repairs or diagnostics? Great work as always 🚘👍🏼

hi Kevin, why do you never use the tool for SAC Clutch ? You have a risk of tiggering the wearing compensation system. Espacialy on LUK and SACHS. Many thanks for your video ! BR JC

How much did it cost to replace the clutch ?

hello kevin. i want to ask you a question. when i change the clutch . i cant put the gearbox back on. i really struggle alot. like i keep on push the gearbox towards the clutch but it never sits . could you please tell me why doesnt the gearbox sit on the clutch. like do i do something wrong

Lovely cars I’d love one Whoever uses Williams appreciates good craftsmanship. Would you ever consider opening a garage or do you love the road. Be safe as always.

What is the red lubricating you took on the threads on the gearbox?

Hi Kev, what was your total time for the job from landing to leaving ?

Great Work! How much does the Clutch Replacement cost for this Volvo?

What is the part in 21:12 called, which is looking like a Z? At this place my car is oily, but i dont know what it called

Hello Kevin, I like your video keep it up but it would be better if you write the autoname in the descriptions instead of the date.

Volvo Ford Mazda 😉

Oil in the turbo tube? Uh-oh.