No video
2011-2020 DODGE JOURNEY HOW TO REPLACE CRANKSHAFT POSITION SENSOR
Рет қаралды 91,439
Күн бұрынI made a how to video on how to replace a crankshaft position sensor on a dodge journey which apply to the following years 2011-2020
@richardhill2379 Жыл бұрын
I just did it this morning at 10:00 am, temp around a 100 degrees. I worked from under the car, used my ramps. It went fairly easy. Going from the top of engine you chance breaking stuff more. Great video !!. You gave me the courage to jump on it.
@chuythemobilemechanic Жыл бұрын
I’m glad it helped you out. Good job
@richardhill2379 Жыл бұрын
@@chuythemobilemechanic Hello Chuy, shortly after the replacmeent I got a second code for intermittant, so I replaced some wire and all is good though today I got another code to deal with PO750, so life goes on, blessings sir
@sealedsecure3754 Жыл бұрын
Bro I have a 2015 Dodge journey 3.6 AND STILL CANT FIND IT🤯😤 I'm under passenger side shining light everywhere even looking behind heat shields but I don't see it please help fellas.
@michaelnichols9916 Жыл бұрын
@@sealedsecure3754 can you use that thermostat? As a reference. And this is a four cylinder. Is your the v6? Can I ask what’s your car doing for you to need to change it. I have a 2015 journey and it’s just stalls whenever but then it’ll run fine then it might not.
@agpilotgt 2 ай бұрын
Chuy, your video had the crucial detail of running the cam crank relearn after installation, something I did not find in the other videos, I thank you.
@ljens8485 Жыл бұрын
Chuy! Hah hah, this video was perfect for me. I have a '17 Journey, stalling out on highway. Sputtering when trying to restart. When to auto store - crankshaft position sensor circuit fault. Got the sensor, had no idea where is was. Your video cleared everything up for me.
@jameswebb1730 Жыл бұрын
What do you do then you don't have the recalibration machine???
@InsideOutMinistries1122 Жыл бұрын
This IS NOT THE CRANKSHAFT SENSOR YOU ARE CHANGING SIR…it’s the CAMSHAFT. Thank you so much for the confusion!!!
@chuythemobilemechanic Жыл бұрын
On this 2.4 engine it is. If you have a 3.6 it’s in a different location. I’m sorry for the confusion. When I made this video I forgot to label the engine
@benhajdu4040 8 ай бұрын
Lmao no. That is 100% the cam sensor youre changing in this video. The crank sensor on BOTH the 2.4 and the 3.6 is located just above the oil pan on the back of the engine. @chuythemobilemechanic
@merrittwolcott 6 ай бұрын
U are correct its the crankshaft position sensor this people have no clue @chuythemobilemechanic
@merrittwolcott 6 ай бұрын
@@benhajdu4040wrong he is correct
@merrittwolcott 6 ай бұрын
It is the crank position sensor on this motor 2.4
@ashleehouse5204 Жыл бұрын
Thanks for the video. Looks like a pain but not impossible.
@calebromero4509 Жыл бұрын
Gracias por la ayuda es muy valiosa para los que cambiamos el ckp a una journey por primera vez
@marcelisteitor 2 жыл бұрын
The classic P335 code, thanks for the video
@yakemtesfaldet7948 2 жыл бұрын
nice job brother u save me a lot of money. thanks
@moshex99 2 жыл бұрын
What u did your car is 3.6 ?
@yakemtesfaldet7948 2 жыл бұрын
my car is V4 2.4L
@rickytintin4782 Жыл бұрын
He’s right it’s the crankshaft hole 2.4 ingine
@MrDirector88 Жыл бұрын
Thank you for your work!
@trapezethedoubledouble1242 2 жыл бұрын
So are working from the bottom and the top of the engine. Could you be mote specific. Thanks
@gregfine 9 ай бұрын
He did both
@TheAverageLifeCassandraA 2 жыл бұрын
What are the symptoms? How’s you know this was the problem. I have a 17 Journey
@chuythemobilemechanic 2 жыл бұрын
It shuts off. The code as well will tell you
@simply_divine6767 2 жыл бұрын
@@chuythemobilemechanic hi was the code p00b?
@moshex99 2 жыл бұрын
@@chuythemobilemechanic the car was stalling while driving?
@michaelnichols9916 Жыл бұрын
I just wanted to know what the car was doing? for you to have to change it? Thanks for the video Chuy
@richardhill2379 4 ай бұрын
Car stalling when in idle. Rough idle, eng feels off when driving and if you have a journey you get the code PO335
@Damngina33 Жыл бұрын
Hi does the same thing apply to a 2010 ?
@nardmatthews9295 2 жыл бұрын
What code did you get
@jimtheedcguy4313 Жыл бұрын
Should be a P0335
@ws2594 Жыл бұрын
What if you get P0366?
@sealedsecure3754 Жыл бұрын
What did you remove from back of engine before you started
@djkingxclusive8581 11 ай бұрын
Heat shield
@sealedsecure3754 11 ай бұрын
@@djkingxclusive8581 Bro 2015 dodge journey AWD you have to take off cv axle and transfer case and part of exhaust to get at it. Horrible. Just did it
@WPGinterceptor460Interceptor Жыл бұрын
replace sensor, and start car.. if runs and no issues then it doesnt need to be programmed!
@Jason-bi9fc 2 жыл бұрын
which engine is this? thanks!
@richardhill2379 Жыл бұрын
2.4 liter vvt 4 cyl. Dodge journey sxt, se.............
@thebakery3996 Жыл бұрын
You didn’t show us anything other than where it is. You didn’t show how to move the lines or where to move them.
@geo8841 2 жыл бұрын
What code did you get to lead you into this sensor?
@WPGinterceptor460Interceptor Жыл бұрын
P0335
@jeffmeeks2930 2 жыл бұрын
Thabk you
@travisplett-yz9gh Жыл бұрын
Help i dont undrstand how to do this
@russbrittain7379 2 жыл бұрын
I'm having a hard time getting to my crankshaft sensor I have a 2011 Dodge Journey Mainstream 3.6 I have it all torn down but I can't touch the sensor what am I doing wrong ?
@chuythemobilemechanic 2 жыл бұрын
Try getting it from the bottom. There seems to be alot of space behind the engine so you should have a better angle from the bottom. Just lift it up with a jack and make sure you use jackstand for safety. There’s two sensors back there so make sure you have the right one
@moshex99 2 жыл бұрын
@@chuythemobilemechanic where is the crankshaft sensor located please, 3.6l journey 2011
@alexisgrier4249 Жыл бұрын
@@moshex99 did you find it im having the same issue
@moshex99 Жыл бұрын
@@alexisgrier4249 in the back of the engine behind back engine mount, near exhaust pipe
@thedw1368 2 ай бұрын
For anyone confused this is the 2.4
@sempergumby8734 2 жыл бұрын
2wd are easy, AWD is hell to replace...
@mikematthews234 5 ай бұрын
I see u can’t even get to it im tryna find the mfka lol
@jeremypoole2054 Жыл бұрын
You changed the camshaft position sensor not the crankshaft position sensor
@gregfine 9 ай бұрын
No he didnt
@thinkofsin9840 Жыл бұрын
So this is not the crank positioning sensor this is the cam positioning sensor
@gregfine 9 ай бұрын
No it’s not
@nicklavioletteiii2183 7 ай бұрын
Might be a good video if your weren't directly in the fucking way for half of it
@johnnygoode8318 Ай бұрын
Hahaha
@terry1417 2 жыл бұрын
How the hell do you put a crankshaft sensor in the camshaft hole that's not the crankshaft dude unless that's a different like the 3.6 that's not where the crankshaft goes the crankshaft is at the bottom of the f****** engine where you actually have to pull the metal plate just to get to it
@hondalude89 2 жыл бұрын
It's on the bottom of the engine. By the Bell housing. That's not a "camshaft" hole.
@VirtualPlayer0187 2 жыл бұрын
Is lot easier from under the car
@Glu7118 4 ай бұрын
So what exactly do you need to do to takeoff the camshaft position sensor from underneath. 🙏🏼
@dannygarza5682 6 ай бұрын
This the crankshaft sensor not the camshaft sensor
@user-qq6bg6vx7t 7 ай бұрын
Taurine t
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 556 М.