not too bad. looks like just one problem screw. but not so much with the right tool. i didn't even think of checking the door gear to see if it sticks. thanks so much bud
@curtisnstacey Жыл бұрын
yes sir, anytime man. i appreciate you stopping by and checking my video out.
@davidsmith57663 ай бұрын
thanks for the info. I went to the hardware store and got screws with 7 mm heads made installation way easier
@curtisnstacey3 ай бұрын
thanks for watching and I appreciate the tip.
@wilber71932 ай бұрын
7mm head how long
@monicasherman88422 ай бұрын
How long did this job take to complete?
@curtisnstacey2 ай бұрын
@@monicasherman8842 about 2 hours. I work kinda slow and thorough
@johnt.7471 Жыл бұрын
Repair does suck because of that one T-15 screw, another video on youtube shows that you need to add a screw on the heater side of the actuator gear that goes on the actuator motor to permanently prevent the blend door from closing stuck on the melted glue. If not, youll be replacing the actuator gear very soon if you still hear popping now when you turn on the heat.
@curtisnstacey Жыл бұрын
I don’t know about all that. Just don’t turn your or ac all the way one way and you’ll be fine. I
@jarome111910 ай бұрын
link to video?
@Dametoven162 ай бұрын
My gears was broken to think I got to replace the actuator to? I put in the gear and is not spinning
@ulikewatuc1ulikewatuc170 Жыл бұрын
Thank you for the detailed and informative video.
@curtisnstacey Жыл бұрын
anytime. no problem at all. i appreciate you stopping by and watching! Thank you very much
@Sheisty25 Жыл бұрын
The gear and slot ship with perrfect alignment when purchasing a new part.. However, my gear on the blend door (passenger side) does not move freely like 3:14. How can I get that gear to align properly?
@marathonnierbagino64902 жыл бұрын
good one, thnks
@curtisnstacey Жыл бұрын
anytime
@JL-ru2bu Жыл бұрын
Do you happen to know the part number to the screws?
@curtisnstacey Жыл бұрын
i sure dont. they screw into plastic. i would try another kind or similar if you cant find the exact ones.
@spsjason23 ай бұрын
I got mine out, not too bad, but my issue is the door it self is stuck..Now what?
@curtisnstacey3 ай бұрын
it may be just stuck with old glue from the factory. can you turn the gear on the door with your hand and move it?
@spsjason23 ай бұрын
@@curtisnstacey I can turn it both directions about 1/4 of an inch and it's very stiff. Tried putting pliers on it, but felt like it was going to break, so I stopped
@curtisnstacey3 ай бұрын
@@spsjason2 I've never seen I've do that unless someone has dropped something down the defrost. I but doubt it'll make it that far. I could tho. Other than that I don't know about that one
@spsjason23 ай бұрын
@@curtisnstacey I cut a small access hole in the side of it and yep, it was gummed up, I was able to get it unstuck and now going to clean it up and plastic weld it back together. Better than ripping out the complete dash for it.
@curtisnstacey3 ай бұрын
@@spsjason2 good idea
@kenanjones6795 Жыл бұрын
The is the most frustrating replacement ever had to do both driver side and passenger side within 3 months😢 passenger side was so much easier
@curtisnstacey Жыл бұрын
you got that right. the drivers side is so freaking bad!!!!