2013 Dodge Grand Caravan 62TE Transmission Valve Body Replacement

  Рет қаралды 114,911

Sell Those Flipping Cars

Sell Those Flipping Cars

Күн бұрын

#dodgegrandcaravan #transmissionproblems #transmissionrepair
Are you having problems with your 62TE transmission valve body? In this video, I show you a step-by-step guide and replacing the 62TE transmission valve body. This 2013 Dodge Grand Caravan has been experiencing transmission problems and has been needing the transmission repaired for quite some time. Due to the cost of the repair the owner of the vehicle was not able to get the transmission repaired. So, if you are having problems with your gears slipping and skipping gears then this is the video for you. This repair if you were to go to a repair shop can cost you between 1600- 2800 depending on the shop and the part price. Thank you for watching and don't forget to subscribe to the channel for more DIY Auto Repair videos.
------------------------Parts Used in Video------------------------
Basic Mechanic Tool Set- amzn.to/3qEqe0U
Remanufactured Transmission Valve body with Solenoid pack- amzn.to/3J5vwJw
Transmission Filter w/ gasket- amzn.to/43ruI9M
Transmission Dipstick- amzn.to/43xPXGU
-----------------------Contents of Video----------------------------
0:00 Intro to Video
2:59 Disconnecting Negative Terminal on Battery
3:28 Location of Transmission Valve body Terminal
11:55 Valve Body cover is removed
12:51 Start of Valve Body Removal
18:34 3 tubes on the back of Valve Body
18:46 Valve Body is removed
→ Become a Channel Member for Exclusive Content! / @sellthoseflippingcars
→ Become a Sellthoseflippingcars Subscriber: / sellthoseflippingcars
→ Help Support the Channel with our Merch Store: / @sellthoseflippingcars
→ Pinterest: / sellthoseflippingcars
→ Facebook: / sellthoseflippingcars
→ Website: sellthoseflippingcars.com
→ My Channel Home Page: / sellthoseflippingcars
→Business Enquiries send to:
sellthoseflippingcars@gmail.com
TubeBuddy is the main tool that I use to manage the backend of my KZfaq channel. It has been a huge lifesaver when it comes to time management and properly optimizing my channel. They have tons of free tools you can check out right here! www.tubebuddy.com/stfc
*If the video was helpful, remember to give it a "thumbs up" and consider subscribing.*
Disclaimer:
Due to factors beyond the control of Sellthoseflippingcars, I cannot guarantee against improper use or unauthorized modifications of this information. Sellthoseflippingcars assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Sellthoseflippingcars recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Sellthoseflippingcars, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Sellthoseflippingcars.

Пікірлер: 472
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Are you doing this repair and are stuck on a specific step? Need help? Join our membership program! Where I personally help you with your auto repairs monthly if needed! kzfaq.info/love/o3SXInKTI8Wt-cB5mDQtWwjoin Membership program starts at $2!!!! Auto Repair shop troubleshoot starts at $140!!! Easy decision!!!
@SLINGING_MUD_SINCE1994
@SLINGING_MUD_SINCE1994 Жыл бұрын
Thank you 😇
@SLINGING_MUD_SINCE1994
@SLINGING_MUD_SINCE1994 Жыл бұрын
Finally got it
@handymanhoney-do6881
@handymanhoney-do6881 Жыл бұрын
Excellent video. I really like the style you have in explaining the process. Still--at 14:30 I said “yeah, this is beyond my skill set”. I try to save enough by doing my general repairs & maintenance that I don’t mind paying for repairs I’m not comfortable doing.
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Thank you! I understand that and never be afraid to take a break. If it seems overwhelming it is usually bc you are tired or hungry. I know it is with me lol thanks for watching!!
@apachewraith
@apachewraith 2 жыл бұрын
Glad I found this. I've been looking all over for the transmission pressure sensor. I saw it on the left as soon as you opened it up 😃
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Glad to be of service Jonah
@RS-kz3gj
@RS-kz3gj Жыл бұрын
Did it fix your problem
@apachewraith
@apachewraith Жыл бұрын
@@RS-kz3gj No I never changed it. I keep getting codes for vacuum leaks and the PCM disconnect. I'm focusing on the PCM. It's not a coincidence, I don't believe, that all of these sensors keep coding but when you fix them they keep coding.
@joseacevedo9117
@joseacevedo9117 2 жыл бұрын
This is beautiful. Love this vid and subscribed. I have had a Trans issue has been Jerking, rarely does it but its there. Threw a code but i forgot which one it is. Ill come back and update once i put the obd 2 scanner. it's been troubling me because my mechanic said the $ can stack up quickly and process of elimination to fix the issue. This video is very informative and helpful. I am alittle intimidated once we start removing the sensitive parts and I learn as I go along. I also tackled opening the engine and putting In spark plugs and coils which was tedious but I loved that I learned it. Felt good to know I accomplished it. Even my mechanic was impressed lol because he said it's a pain In the ass to work on this platform. Thanks a bunch and wish me luck! Also I'll be using a Autel MaxiPRO MP808 scanner. Friend gave it to me because he doesn't do work on his cars himself. Just found out it's worth about 750$ lol.
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Sounds great Jose and yes the tools cost quite a bit the longer you are a mechanic and the more elaborate tools you need.
@paulmontgomery4696
@paulmontgomery4696 2 жыл бұрын
That was a great video to watch and now I’m glad to say I’m a new subscriber keep up the good work
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Thank you Paul! I'm glad that you enjoyed the video and welcome to the channel!
@terrenceneeley726
@terrenceneeley726 5 ай бұрын
Bro best creator, fr one of the best creators of car vids
@Sellthoseflippingcars
@Sellthoseflippingcars 5 ай бұрын
Thank you brother ❤️ I really enjoy hearing that my videos help people.
@prashanttrivedi2537
@prashanttrivedi2537 8 ай бұрын
You have explained very well. Neat job. Thank you. 👍
@Sellthoseflippingcars
@Sellthoseflippingcars 7 ай бұрын
Thank you! Make sure you subscribe for more Auto tips this year! Thanks for watching!
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
I am so happy this video has helped so many people!!!! Thank you everyone for your continued support!! Dont forget to subscribe for more DIY Auto Repairs here on the channel!!
@walbertomatias7498
@walbertomatias7498 3 күн бұрын
Thanks for making this video This video help me a lot
@Sellthoseflippingcars
@Sellthoseflippingcars 20 сағат бұрын
You are most welcome! Thank you for watching!
@ziarehman8057
@ziarehman8057 2 жыл бұрын
Wonderful tutorial!
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Thank you! I am glad you enjoyed the video and found it beneficial
@tjtheadvocate8856
@tjtheadvocate8856 2 жыл бұрын
You rock Zach. These videos are so helpful. Bless you sir for taking time to share knowledge and save this chick hundreds/thousands of dollars. Geshhhhh i would welcome a Zach clone here in GA anytime.
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Thank you! I am glad you find my videos beneficial and saving you money! What part of GA?
@tjtheadvocate8856
@tjtheadvocate8856 2 жыл бұрын
@@Sellthoseflippingcars Fairburn 15 minutes outside of Atlanta
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Nice! What all problems are you having? I can make some videos for you
@tjtheadvocate8856
@tjtheadvocate8856 2 жыл бұрын
@@Sellthoseflippingcars wow so grateful. How can I donate? I need blower resistor motor(rear I was told) and rocker arm. My Dad says many times rocker arm causes tick as no codes for motor. I use it for my Medicaid transportation services. Also said 2 transmission hoses with fluid chg. I am cramming all your vids. You have one for blower resistor. I want to donate. Thx sir
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
I can create those videos for you no problem. Give me 2 weeks please to find another Grand Caravan or Town and Country to do the videos on. I have a membership program that helps support the channel or you can use my Paypal to send donations to which is @sellthoseflippingcars
@nwafrugalfinds8650
@nwafrugalfinds8650 2 жыл бұрын
Love this video! We are trying to salvage our beloved mini van. I was driving and it started acting up. Sputtering a bit whenever it shifted down or when I pushed on the gas it was a little delayed trying to get moving. It was very sudden and I tried to get home but it ended up totally failing while going up a hill. It now will start and run great but will not move at all. It was giving a code for Fluid pressure sensor A circuit permanent. Do you think changing the solenoid and filter and putting in new fluid could fix this? We have four kids and gotta get this thing going one way or another preferably without having to get a new vehicle 😖 the prices are sky high right now!
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Yes, and also make sure you replace the Orings on the vacuum tubes. Thank you for watching! Dont forget to like and subscribe for more DIY auto!
@al197861
@al197861 3 жыл бұрын
Awesome information bro
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
Thank you Alfred! I am glad you enjoyed the video and found it to be beneficial! I hope your Grand Caravan is back up and running!
@artemioolivas5689
@artemioolivas5689 Жыл бұрын
Hi. Great video. I have a 2012 dodge cravan P0806 and P1745 codes. Doesnt shift past 2nd gear max mph is 40. Can I fix by replacing clutch solenoid or should i replace the valve like in the video? Thanks! All the vid and comments super helpful
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Yes you can, but I found it to be more cost efficient to just get the valve body since it comes with the new solenoids already on it. Compared to buying the solenoids one at a time. I did link the valve body in the video description if you are looking for one. Thanks for watching!
@belowfray5251
@belowfray5251 Жыл бұрын
Real good. Thanks!!!
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
You are most welcome! Thank you for watching!!
@mattmcnamee4717
@mattmcnamee4717 Жыл бұрын
Thanks for this video! I have a 14 Grand Caravan. It goes into park, reverse and 1st gear. Unknown service history. Would you think a new solenoid would allow the transmission to shift into the other gears?
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Yes it definitely would! But check if you have any transmission codes 1st
@kylemaleport1685
@kylemaleport1685 Жыл бұрын
Your videos are great! The breakdown on them are easy to follow and understand. I’m at this video now due to transmission troubles. Recently replaced the alternator, serpentine belt and PCM on 2011 town and country. After the PCM drove it for a week and now it’s having transmission problems. Won’t reverse after the car runs for a couple minutes but when it first starts it will. Throwing multiple codes (p0733, p0868, p0870, p0836 & p084a). Any ideas what could cause the reverse not to work after running for a minute or two?
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
You need the testing transmission dipstick, it is a tool by Mopar to check the transmission fluid. I show you how to use it in this video kzfaq.info/get/bejne/kK6SqKimm62wm5c.html You have low transmission fluid, (P0868) You need to fill the system and retest. I am glad you enjoy the videos, please let me know if you have any additional questions. Thank you for watching!
@kylemaleport1685
@kylemaleport1685 Жыл бұрын
Thank you for the reply, subscribed to your channel. I bought the transmission dipstick and have enough fluid in there according to the diagram. It whines when it starts. Will reverse for a min or so and then won’t until the car is restarted. I’m going to change the filter next weekend but was wondering if this part “Trans Pressure Transducer Sensor - Mopar (5078708AC)” could be the culprit? I’m stumped at this point.
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
All of the sensors that deal with your vehicle shifting are located on the solenoid pack. Are you getting any transmission codes?
@jimmyau5365
@jimmyau5365 10 ай бұрын
Love it , great video
@Sellthoseflippingcars
@Sellthoseflippingcars 10 ай бұрын
Glad you enjoyed it! Thank you for watching Jimmy!
@freddyliriano2000
@freddyliriano2000 Жыл бұрын
Excelente explicación
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Thank you and thank you for watching!!!
@mikestepan7478
@mikestepan7478 2 жыл бұрын
What’s up man, great vid. Did U use silicone for the pan or get a gasket?
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Hey Mike! Thank you for watching I am glad that you found the video beneficial to your transmission valve body replacement. I used silicone for my transmission pan reinstall.
@SLINGING_MUD_SINCE1994
@SLINGING_MUD_SINCE1994 3 жыл бұрын
Great video
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
Thank you Carolina! I am glad that you found the video to be beneficial and you enjoyed it. That makes it all worth it to me. Thank you for watching!
@revinlight
@revinlight Жыл бұрын
Thank you, thank you, thank you!!
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
You are most welcome Robert! I am glad your found benefit in my videos! Dont forget to subscribe for more DIY Auto repair here on the channel! Thanks for watching!!
@revinlight
@revinlight Жыл бұрын
I ordered the part from the link you provided on Amazon. Reviews were mediocre. Any issues with the one you bought? Subscribed!!
@2001jamiewolf
@2001jamiewolf 6 ай бұрын
i'm working on my dads right now and it shifts out of 2 when it feels like it. get over 40 to 45 and it's like it's in neutral
@henrypagan6657
@henrypagan6657 2 жыл бұрын
Thanks for the video I just got a new transmission six months ago and it feels like you’re skipping. Should I change the oil and filter
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Yes check the color of the fluid. That will tell you a lot about why the transmission is skipping. If it is dark change it and the filter
@henrypagan6657
@henrypagan6657 2 жыл бұрын
@@Sellthoseflippingcars thanks
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
You're most welcome!
@CHEAPROLLIN
@CHEAPROLLIN Жыл бұрын
Hey thanks alot I mean use this as a reference on my
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
I am happy to hear that brother! The Dodge Caravan even though it is a great vehicle, it had some problems with it but hey......what doesnt? Am I right? Thanks for watching brother!
@CHEAPROLLIN
@CHEAPROLLIN Жыл бұрын
@@Sellthoseflippingcars yes sir I appreciate those videos thank you
@emilehagege
@emilehagege 7 ай бұрын
excellent video, with lots of very interesting explanations. In your opinion, why does my gearbox, when it reaches more than 80° and when I almost come to a stop, the engagement of first gear is sometimes a little abrupt and sometimes idling is a problem a little unstable. Thank you for your response, it would help me a lot. 13000km
@Sellthoseflippingcars
@Sellthoseflippingcars 7 ай бұрын
I am going to guess you meant 130,000 km's and my 1st question would be are you receiving any transmission and engine codes. Sounds like a pressure problem but you need to confirm with transmission codes that you are receiving. Same with rough idle, that could range through ALOT of problems, knowing the engine code would narrow the search down. Especially since I don't have the vehicle in front of me. Thanks for watching and I await your response.
@emilehagege
@emilehagege 6 ай бұрын
thank you for your feedback, I have had the diagnostic case carried out there is no error code neither in the engine nor in the gearbox, I bring you two details a few days ago, I wanted to pass the gears manually at low speed and a low pressure error code is displayed on the diagnostic, second thing, I noticed that when the box is very hot there is a little bit of the smell of engine oil. Box, which goes back to the passenger compartment? Thank you again for your clarifications.
@syserr7318
@syserr7318 2 жыл бұрын
I have a 2013 200 with the 6 speed trans. I put in a used one and the connector to the solenoid is different than my old trans. Can I just change out the solenoid pack or do I need to do something else?
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Yes just change out the solenoid pack with the correct one you have a different model number
@johnlucero8237
@johnlucero8237 Жыл бұрын
P1745 2018 dodge journey sxt 3.6 when going from park to drive or neutral to reverse it shifts hard while foot is on the brake. I tested pin 12 line solenoid with positive lead on 10 it was 5.5 ohms all other pins checked out within spec. But it stays in the same gear won't shift to other gears for highway speeds. Replaced filter and fluid as well.?
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Shift solenoid is on its way out, reverse is the 1st one to always go out 1st
@josuegalvez1
@josuegalvez1 Жыл бұрын
Thanks
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Anytime Josue!!!! Let me know if you have any questions and thank you for watching!!
@ThatsNotZon
@ThatsNotZon 2 ай бұрын
I just did mine to try to fix my reverse issue but now it just won’t go into drive, opposite problem but worse because at least I could drive it before, hoping you know what happened
@Sellthoseflippingcars
@Sellthoseflippingcars 2 ай бұрын
You need to fill the transmission fluid to the correct level. Use a long funnel to fill where fill plug is located. Having the transmission dipstick from video will help get to correct level
@ourhousedeals5152
@ourhousedeals5152 2 жыл бұрын
I have a 2016 Grand Caravan with 85k miles. Yesterday I was driving and heard a whining sound. I was in a bad area at the time so I jumped on the highway, drove about 10 miles, and when I exited the highway, after coming to a stop, the van wouldn't go. It wasn't catching gears for a few seconds then finally caught gears enough to get it to the side of the road [no lights on dash]. I called a couple people, and decided to take a chance to go another 15 miles home. The ENTIRE TIME it would only go up to 2nd gear and sometimes wouldn't even do that. I finally got it home. There are still no warning lights on. I checked the trans fluid level with my scored oil dipstick [I learned to do this from other YT mechanics], and it read way too high. The fluid itself did not smell burnt and looked ok. I siphoned about 1.5 qt out to get it right at the top of the hot line. It's still having the same issue. Still no warning lights. This is our only vehicle. Advice would be MOST APPRECIATED. Thank you in advance!
@ourhousedeals5152
@ourhousedeals5152 2 жыл бұрын
Update: I disconnected the battery for a while and reconnected it. From what I read, that exited "limp mode." The van started to go then I heard the whining sound again, and the same thing happened [STILL NO WARNING LIGHTS ON]. I don't know how to diagnose it.
@ourhousedeals5152
@ourhousedeals5152 2 жыл бұрын
Update 2: After disconnecting the battery again, I finally got the van to throw code P083B
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Writing response in update below
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Ok, first of all that is not correct with your transmission dipstick, unless you checked the temperature of the transmission before checking the transmission itself. On the 62TE transmission the correct way is to check the transmission temperature by using live data on a code reader that has it, then taking that temperature and checking your transmission fluid level table that should of came with the transmission dipstick that is in the video description. Just seeing if you have transmission fluid is great and all, but if you do not know how to read it then it does no good at all. The other videos you watched showed you a great way to save $12 and getting the correct tool for the job. Now back to the problem at hand, when you unhooked your battery, you reset the computer just like you would a desktop. Sometimes the operating system will correct the problem then other times it wont if it is a hardware issue. What you have is a hardware issue. You do not have an engine code but I am sure you have a transmission code. On the Dodge Grand Caravan it only shows transmission codes if you have a code reader that can read transmission codes (not all code readers can). I would say from what you have said you have a faulty shift solenoid and since this solenoid is electrical when you reset the computer it tried to reset but failed. Double check for transmission code, but the part you need is in the video description. It is the transmission valve body, it comes with the new sensors. This is the cheaper option then just buying the sensor by itself, from what I found. Hope this helps!! Thanks for watching and subscribe for more DIY auto repair!!
@ourhousedeals5152
@ourhousedeals5152 2 жыл бұрын
@@Sellthoseflippingcars Thank you so much! I am trying to get someone here with a decent scanner that can scan the trans codes.
@mkanaar
@mkanaar 21 күн бұрын
I have trans fluid coming out of the overflow valve (everyone calls it something different) on top of the transmission which makes me believe I have too much pressure or a temperature problem to make the fluid boil out. Any idea? So far, I have about 20 different ideas which could become a real financial problem. Mine is a 2014 town and country 3.6 62te
@Sellthoseflippingcars
@Sellthoseflippingcars 10 күн бұрын
What transmission trouble code are you getting?
@clicketysplit1817
@clicketysplit1817 10 ай бұрын
I have been told on many occasions that when scanned there are low voltage codes. When I look at the connector where the harness plugs in (in the beginning of your video) it is in direct line of water drainage resulting from a sun heat warped windshield gutter not allowing water from rain or a car wash to drain off to the sides properly, instead it runs directly into to engine compartment and onto the harness and plug causing shortage. At one time after going through the car wash I noticed a weird burning plastic smell inside the car, sort of like an old transistor radio would smell if it overheated. Now as soon as I put the AC on it seems to put a drain on the voltage causing the miscommunication resulting in the trans downshifting from low speeds sort of rough. I brought it to Aamco and they tell me that a remanufactured transmission with labor is about $6K, but I know it's not a hardware issue, it's electrical. There is nothing wrong with the gears inside the transmission because it runs through all the gears fine without slipping getting up to speed, but when downshifting from low speeds it doesn’t seem to know how to respond at times, especially when I have the AC on in circulation mode.
@Sellthoseflippingcars
@Sellthoseflippingcars 10 ай бұрын
Sounds like the plug needs cleaned or covered after replacement to prevent this from happening again. If there is nothing wrong mechanically then it's all electronic. What are you thinking of doing? Repairing it yourself and saving the $6,000? By the way I do have a complete transmission replacement of this vehicle walkthru as well. I got the transmission for $400, $6,000 is quite steep
@michaelparker2319
@michaelparker2319 Ай бұрын
Does the van need to be level? I can’t stop the trickle out the back of the port to get a good seal with rtv
@Sellthoseflippingcars
@Sellthoseflippingcars Ай бұрын
Yes, the van needs to be on a level surface
@kenio09
@kenio09 2 жыл бұрын
I have Fiat Freemont 3.6 2014 year which is Dodge Journey and have weard issue with it. The car, after warming up and driving for about 15-20 minutes, 80-100 km / h when braking to 0 before a crossroads or lights, sometimes starts to jerk as if it did not disengage the gear, the engine shakes, it pulls the gear even though I am braking. If it is dragged on the brake to 0, it will go off, or if the brake is released, sometimes it will manage to give up a gear and will not go off. It never happens in the city itself when driving up to 60-70 km / h, only on the road and only when I’m braking to 0. No code. I could add that few months ago I had change fluid (the mechanic said that he poured the appropriate fluid designated for these cars). I’ve read on one forum that changing 62TE TCC Solenoid could fix the problem, do You have this kind of situation earlier with any Chrysler/Dodge?
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Yes it could be the TCC or a stuck caliper on your brakes causing the intense shaking
@victorraymond9430
@victorraymond9430 21 күн бұрын
Hi, is there a gasket for the valve body cover or can you use silicone gasket maker?
@Sellthoseflippingcars
@Sellthoseflippingcars 7 күн бұрын
You can use RTV for the gasket
@brandonmcintosh9575
@brandonmcintosh9575 Жыл бұрын
I'm under a different profile but I'm the one with the 2013 t&c. I took the pan off and drained the fluid. All I see are shavings in there that turn to mush when you try to pick them up with a paper towel. Is that normal with 166000 miles on it? I also had it flushed a few years ago but I don't know what all they did to it.
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Yes, that is normal in a transmission pan. Shavings and slivers are normal it is when you see metal chunks that is a very bad. Remember in your transmission it has metal on metal contact with the gears turning. Your transmission fluid, lubricates and disperses heat placed by said friction of the metal. Make sure to change your transmission filter, and fresh fluid to keep your transmission running for years to come.
@cspl3474
@cspl3474 2 жыл бұрын
pretty new at this but financially need to be able to do more repairs or know what I need when taking for repairs.My Journey with 62te will not shift out of first, drives, high rpm but not shifting. It will reverse (I am not driving it until problem diagnosed) What should I check? appreciate what you are doing thanks and subscibed
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Are you getting any transmission trouble codes? You will need a code reader that can read transmission codes. Thank you for watching and welcome to the channel!
@christopherconnor1988
@christopherconnor1988 Жыл бұрын
Same with mine, code P0882
@LateNightRituals
@LateNightRituals 2 жыл бұрын
Thank u
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
You are most welcome! Thanks for watching!
@geraldocabral5969
@geraldocabral5969 Жыл бұрын
Hello, my Journey 2014 3.6 went into emergency mode and made a cavitation noise in the Valve Body, I replaced the Filter and the oil because it was clogged and after I replaced the oil and the filter the Code P083B appears, already I reset the code with a scanner but the code comes back, I've already checked all the electrical harnesses, everything is ok, and no noise appears. Could it be the valve body? Or the Pressure Sensor?
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
The pressure sensor is going to be located on the valve body and will be cheaper to just replace the valve body since it includes the sensor as well. Make sure to check your orings when reassembling, you have a pressure problem, even the smallest oring can make a difference when it comes to having the correct pressure for your transmission. Thank you for watching!
@wojo8881
@wojo8881 5 ай бұрын
Is it necessary for the rooster tail comb be in the correct position for gears to shift correctly . I got in 6 valley
@Sellthoseflippingcars
@Sellthoseflippingcars 5 ай бұрын
Yes, the groove needs to be in the set position. If you don't then your shifting will be incorrect
@stansengun
@stansengun 2 жыл бұрын
Awesome video. What was the purpose for replacing solenoid pack? I have a code that came up last week P0841. Does replacing this pack resolve the issue. My transmission has been engaging but it’s kind of delayed. Any advice is greatly appreciated.
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Thank you, I am glad you enjoyed the video! With that code you are having a problem with your pressure sensor circuit. The solenoid pack holds that pressure sensor. When is the last time you have serviced your transmission? While you are in there I would replace the transmission filter and new transmission fluid as well.
@stansengun
@stansengun 2 жыл бұрын
@@Sellthoseflippingcars I just purchased the van through an auction. I drove it back and the transmission seems to shift a little weird at low speeds. But on the highway, it drive fine. If I was to replace the solenoid, will it solve the problem?
@CashApp-HelpMeStayAlive
@CashApp-HelpMeStayAlive 2 жыл бұрын
@@stansengun Did you change the Trans filter and Trans oil ?? Start with that .
@danvon7490
@danvon7490 2 жыл бұрын
I have a 2013 grand caravan replaced the transmission fluid and replaced the transmission filter and it’s making a whining noise??
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Did you add the correct amount of transmission fluid? Keep listening for the whine while you add more transmission fluid. The whine will slowly go away, that is how I know I am getting to the proper fluid level.
@MrDumonic
@MrDumonic 2 жыл бұрын
Also found out that they did two recalls. Some cover for the steering wheel wiring, and a software update. Whoop, whoop 🙌. She drives like a brand new vehicle. The shifts I noticed are a lot different, almost like they’re closer together. That was part of the software update. I’m so scared to drive it 😟 and it break down 😂. The 3.6 is a great engine. I drive it real easy, if only I did the pan and filter instead of a fluid exchange at the quickly lube. I probably could have gotten more out of it. But a snow plow did hit my vehicle in the front drivers side all the way down to the rear. He was backing up and smoked my parked vehicle with his blade. I drove it home, but never went over 50. Then I noticed I had this problem with the transmission. Not sure if it’s related, but I noticed the limp mode the next day. Body shop picked it up with a tow truck. Got it back and they said no visible damage to the transmission, not part of the accident. Took it to the dealership as mentioned to get a diagnosis. And this is where we are at. Pan and filter changed, full fluid flush. Codes p1745 and p0868 along with my oil codes. Pan/filter and flush didn’t fix the issue. Fluid was a little burnt and no debris found in the pan 😮‍💨. But as you know, the pack, valve, and range sensor had to be replaced…accident related??? I couldn’t ask the dealership because I picked up my vehicle after hours and it was just a secretary.
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
If the oil is burnt then the valve body and solenoid pack were seeing increased heat due to fluid being dirty.
@MrDumonic
@MrDumonic 2 жыл бұрын
@@Sellthoseflippingcars thank you.
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
You are most welcome Dominic!
@stevehamman4465
@stevehamman4465 2 жыл бұрын
@@Sellthoseflippingcars 2011 , stuck in first gear, happend today. Getting p1745 and po868 codes. Haven't tore onto it yet ,its the neighbors and I'm just trying to get info! What do you think?. Thanks in advance!
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
@@stevehamman4465 0868 is your pressure sensor malfunctioning. Yet 1745 is transmission fluid pressure is running too high. This makes me think 2 things 1) when did you change the transmission filter and fluid last? 2) what level is the trans fluid at?
@wesdbry
@wesdbry 2 жыл бұрын
My 2013 caravan tries to kick into passing gear when at only 2500rpm while still in low gear. You have to speed up very slowly not to have passing gear engage. Is there any reason for this?
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Check to see if you have any transmission codes. If not unhook both sides of battery for 30 minutes so you can reset the TCM.
@teeybannister
@teeybannister 2 жыл бұрын
We got a Town and Country. It will drive but once you start it, when you put it in gear it does this. What could be the issue?
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Check your transmission oil level, it could be that your fluid is low. If you have never changed your transmission fluid then you are looking at doing a transmission fluid change at least.
@fishinwithhomer
@fishinwithhomer 2 жыл бұрын
I got P084B and out can is in limp mode, which would be better to replace, the valve body or solenoid pack?
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
With that transmission code you are needing to replace your TCC Solenoid which is attached to your solenoid pack. It is cheaper to purchase the solenoid pack as a whole. I found mine on Etsy and it was remanufactured. Let me know if you need the company's link I order mine from, it will save you a few hundred dollars.
@fishinwithhomer
@fishinwithhomer 2 жыл бұрын
@@Sellthoseflippingcars I’m getting the solenoid pack today, the tcc is the one that has the fragile clip? If so, the solenoid pack doesn’t have the tcc..
@story1234
@story1234 Ай бұрын
Perhaps you can help me with my 2012 Caravan at 230,000km. I bought it to convert it to a camper van so I got it cheap with problems. Problem 1. There’s rough idle in Drive and the seller said there’s a misfire. The is no vibrate when stopped in neutral. Problem 2. There’s jerking when I release brake and brake again. The steering wheel will jerk. The alignment is off right now for sure. Otherwise it runs fine going 100km without clunks. Transmission is fine. It brakes fine from that except the slight jerking on the steering wheel. Driving it would have that jerking too.
@Sellthoseflippingcars
@Sellthoseflippingcars Ай бұрын
Sounds like you need a tune up and new brakes, I would check the suspension while you have the tire off. Inner and outer tie rods and stabilizer links are always good to keep in good order.
@russellsnyder4221
@russellsnyder4221 2 жыл бұрын
I have a 2013 caravan and its slipping in between 4n5 and 5n6 would this solve problem I replaced filter and fluid. no change
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Check to see if you are getting any transmission codes
@SLINGING_MUD_SINCE1994
@SLINGING_MUD_SINCE1994 Жыл бұрын
Bro I got the 3 hoses in but the valve body I’m having a hard time putting it back all the way
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
You have to do it be feel brother, the tubes are bent, So do a hook with them when reinstalling, when you hook it into the hole they go into, you will feel the holes they are supposed to sit in. After you push them in, give them a little bit more of a push and you will feel them, almost click but they will fit snugly into their resting spot. After you get them installed, then reinstall the tubes onto the back of the valve body, this should make it easier. Hope this helps brother
@SLINGING_MUD_SINCE1994
@SLINGING_MUD_SINCE1994 Жыл бұрын
@@Sellthoseflippingcars the tubes are not my issue anymore it was the bottom pin
@SLINGING_MUD_SINCE1994
@SLINGING_MUD_SINCE1994 Жыл бұрын
Bro does the bottom pin that you said don’t bend I got a new one from Amazon and it’s hard as a rock doesn’t move left or right
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
There is no lubrication at all like there was in the old valve body, that pin is moved with great pressure from the transmission
@vincentrivest6235
@vincentrivest6235 9 ай бұрын
thanks boy
@Sellthoseflippingcars
@Sellthoseflippingcars 9 ай бұрын
Your Welcome Vincent! Thanks for watching!!
@oleksandrhavryliuk6825
@oleksandrhavryliuk6825 Жыл бұрын
Hello! i have the same transmission on my 2013 dodge avenger sxt 2.4l 6 speed i have a problem with it while driving when i drive 30 miles and start braking and the transmission shifts shifts from 3rd gear to 2nd gear and at this point when it shifts at 20 miles i hear a thump Even when the car is stationary, it works, I try to switch gears from P-R-D, I hear kicking, and when I checked, the engine moves as if all the supports are broken, although the supports are in normal condition
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Sounds like you have an internal gear issue with your transmission. Are you getting any transmission codes from a code reader? Make sure the code reader can read transmission codes or you wont be able to see them.
@michelletrinidad9825
@michelletrinidad9825 Жыл бұрын
I have a Dodge Caravan 2012 I change the transmission but when they get the spray way for 45 minutes no stopping 60 mile four hour does transmission start kicking I need to know if it’s a sensor or the transmission
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Do you have any transmission codes? (You need to make sure the code reader you are using can read transmission codes)
@JacobParkYusuk
@JacobParkYusuk 3 жыл бұрын
Would a P0868 on a 2013 Caravan be fixed by this, or could it be one of the wires/plugs that go into the transmission?
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
Yes this would correct the p0868 diagnostic code on the 2013 Dodge Caravan. With this diagnostic code being brought up due to low line pressure. The three lines that are in the back of the valve body. The 3 metal lines that I show in the video make sure you replace the O-rings that are on those tubes.
@JacobParkYusuk
@JacobParkYusuk 3 жыл бұрын
@@Sellthoseflippingcars thanks!
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
You are most welcome
@frankieserrano7426
@frankieserrano7426 3 ай бұрын
I got the same problem
@tomley643
@tomley643 Жыл бұрын
I have a 2017 dodge grand caravan I backed up it shifted hard into reverse trans began to shift hard into gears made it home luckily no codes. Let it cool down started it and got codes p083b and p0841 van doesn't want to move. Outside temp 29° buddy's scanner said trans temp was 44.67° it whines in park and netural. Transfuid is darker than it should be, appears 2 be on the fuller side but that's with marking out the oil dipstick hack. And engine warm but can't drive to heat up fluid with friction. What would you try?
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Sounds like that solenoid is cooked, the fluid being dark only means the filter is even darker. The tiny screens in the solenoid freeze up when sediment is in the system. Time for a flush or replacement...veering more towards replacement time.
@tomley643
@tomley643 Жыл бұрын
Are you referring to change solenoid pack or transmission itself? Thanks
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
@@tomley643 I am speaking about the solenoid pack
@MrDumonic
@MrDumonic 2 жыл бұрын
Update. Vehicle is done. They also changed the range sensor, and not just the pack, but the whole valve assembly. Total is $2105. And they threw in a free inside and outside detailing. Gave me 10% off of the parts, and 2 years parts and labour warranty (unlimited Km’s).
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
That's what I did as well, replaced the entire valve assembly and solenoid pack. Good to hear you got your vehicle back on the road.
@clicketysplit1817
@clicketysplit1817 10 ай бұрын
Where did you bring it?
@belowfray5251
@belowfray5251 Жыл бұрын
Subscribed
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
welcome to the channel!
@christopherconnor1988
@christopherconnor1988 Жыл бұрын
Hi, i had a secondhand good running trans sitting in the shed, i took the whole valve body out and stuck it in my current journey, now I'm only getting first and reverse, do i need to get that valve body coded?
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
No the valve body does an automatic learning process after 30 miles. Did you refill trans fluid and replace the rubber orings?
@christopherconnor1988
@christopherconnor1988 Жыл бұрын
Rubber orings looked to be in good shape, So i left them, i changed the trans filter and filled with new oil, i can't drive for 30 miles, because it literally stays in first gear, Even when i put it into tiptronic mode, it will show 1 on dashboard, but immediately jump into D when in motion.
@albutterfield5965
@albutterfield5965 11 ай бұрын
Out of all these videos that shows how to do this I was not able to find one that had the 3.8 engine. I have a 2010 with the 3.8 engine which requires you to take the exhaust crossover pipe off in order to get the sound shield and the metal cover off. The bolts that hold this pipe on that connect to the exhaust manifold that is next to the fire wall are had to remove and take some time, the nuts are special ones with a locking tab so try not to lose them. you will also need to get 2 exhaust gaskets before you reinstall this pipe.
@Sellthoseflippingcars
@Sellthoseflippingcars 11 ай бұрын
The replacement kit online has the exhaust gaskets in the kit. Just make sure you put your model engine correct and it will be good to go. I have another transmission replacement video for the 62TE and the transmission I pulled came off a 3.8 with the exhaust crossover. The exhaust crossover is the only difference in the removal process. If you have any questions during the repair, feel free to message and I can help you out. Thank you for watching!
@albutterfield5965
@albutterfield5965 11 ай бұрын
@@Sellthoseflippingcars I did have to order the gaskets from a local auto parts store, told them that the engine was a 3.8 the gasket arrived and they were for a 3.6, the design of the gasket was different but they fit.
@Sellthoseflippingcars
@Sellthoseflippingcars 10 ай бұрын
How is the vehicle running now?
@mayegillock4724
@mayegillock4724 2 жыл бұрын
Mine won’t go in reverse all other fine 209 Dodge Grand Caravan slt 4.0 motor any suggestions
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Are there any noises or codes? You should be receiving a transmission code because it sounds like a solenoid just failed, if you are getting no noises.
@marcustaylor3943
@marcustaylor3943 Жыл бұрын
Is there a preformed gasket to purchase or did you use some sort of RTV to seal the valve body cover?
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
The transmission filter with gasket is listed in the video description
@marcustaylor3943
@marcustaylor3943 Жыл бұрын
@@Sellthoseflippingcars Thank you for your response. I know the transmission pan has it where the filter goes below. I was referring to the valve body cover in the video. I can't find any information on a gasket for that and wondered if the Permatex A/T gasket maker was appropriate to use there.
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Yes, permatex/rtv silicone will work fine there. I used gray myself but blue works too. Thank you for watching!
@raulmorales7971
@raulmorales7971 11 ай бұрын
I have a 2011 Dodge Grand caravan crew and I replaced the shift solenoid and it not shifting in 2nf gear but in other gears changes fine
@Sellthoseflippingcars
@Sellthoseflippingcars 11 ай бұрын
Are you getting any transmission trouble codes?
@raulmorales7971
@raulmorales7971 11 ай бұрын
@@Sellthoseflippingcars just the solenoid keep messing up I have changed it 2 times
@Sellthoseflippingcars
@Sellthoseflippingcars 11 ай бұрын
Which code are you getting? That is the difference between a sensor or the whole pack needing replaced.
@raulmorales7971
@raulmorales7971 11 ай бұрын
@@Sellthoseflippingcars P040 thats the code I get
@madmike214
@madmike214 2 жыл бұрын
Any suggestions on what to look for in scan data or even on a scope to catch the issue? I have a customer (2012 tc) that's says it feels like it's sputtering in 2nd up hills, very intermittent....i haven't confirmed the complaint yet (car Will be dropped off Sunday for a diagnosis) but the way she describes it, sounds like she's describing a misfire....however the side pan is leaking so she may be right. I'll have to interrogate her more thoroughly and have her drive the car with me in it.
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Is she getting any engine trouble light on? I always like to think of vehicles as a puzzle and a good puzzle leaves bread crumbs. If it is a transmission issue you will be getting a trouble code but your code reader must be able to read transmission codes. Start with the codes and go from there.
@madmike214
@madmike214 2 жыл бұрын
@@Sellthoseflippingcars I always do a full scan report pre and post service on all my vehicles so maybe there's something, I have 4 scan tools ( verus, autel 906bt, smartdiag, and can use factory through my cardaq3+ j-box). Just wondering if there is anything in particular I should be looking at. And like I said, how she described it sounded more like a miss than a trans problem. I'm a mobile diagnostic tech but admittedly my weak point is transmission diagnostics.
@madmike214
@madmike214 2 жыл бұрын
Oops! I ment thinkdiag not smartdiag lol
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
If it is the transmission you will be getting a low pressure transmission code. If you are experiencing a misfire then you will be experiencing that in every gear not just 2nd. If is sputtering you might want to look at your fuel system. There are a few things it could be but the best thing would be to look at the vehicle and diagnose from there.
@madmike214
@madmike214 2 жыл бұрын
Well, trans is low at cold point and still waiting for it to reach temp to read the operating temp point...bored waiting for this to reach temp do I'll replying now 😆 i also found the battery is bad...I'm not surprised...this customer has multiple cars that I've been servicing (from a now out of business shop) and they ALL have had bad battery or terminal ends!! Not kidding..ALL!! I know Chrysler likes to do load shedding and can cause all sorts of issues with drivability so after getting the right amount of fluid in it I'll have to sell her a battery before I can move forward. I Should just tell her to get a new battery installed in anything I haven't serviced for her yet before bringing it to me 😆.
@hiddenghost9200
@hiddenghost9200 2 жыл бұрын
I have 2011 dodge caravan an had transmissions slipping I bought a remanufactured shift solenoid installed it an back to acting up again was I suppose to what you pointed out @ minute 16:00 let me know please. Thanks
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
you purchased the shift solenoid pack only? did you clean the valve body while you had it out?
@hiddenghost9200
@hiddenghost9200 2 жыл бұрын
Only purchased shift solenoid didn’t clean valve body to be honest
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
How did the repair go? How is the vehicle running?
@hiddenghost9200
@hiddenghost9200 2 жыл бұрын
@@Sellthoseflippingcars took it to the shop an was slapped with 3600$ in repairs, now running like a baby!
@horaciotellamedo6141
@horaciotellamedo6141 5 ай бұрын
muy bueno el video pero no dijiste cuantos litros de aceite lleva y que tenes que hacer un aprendisaje rapido al cuerpo de solenoies
@Sellthoseflippingcars
@Sellthoseflippingcars 5 ай бұрын
Eso serían 5,2 litros y no, no tienes que hacer un proceso de reaprendizaje. Debe asegurarse de que el líquido esté en el nivel correcto utilizando la varilla medidora de prueba de transmisión. Entonces te sugiero que cambies de marcha antes de salir en un vehículo en el que acabas de reemplazar la transmisión. ¡Gracias por mirar!
@jamiemorgan6150
@jamiemorgan6150 2 жыл бұрын
My 2016 Dodge journey is reading P0750 what does this mean thank you
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Check your transmission fluid level and color first. The code means your reverse solenoid circuit is low. Worst case scenario you need a new valve body. But start with the fluid and color first.
@obamitsui7795
@obamitsui7795 Жыл бұрын
My 2013 t&c just stranded me. It starts and runs good but it won't go anywhere. Feels like it is in neutral when i put it into drive. Will this most likely fix that problem? And if so, where is the video description at so i can see all the parts that i need? Im not too technologically advanced lol. I just want to get everything that i need. Oh and thank you for this video! You make it seem pretty simple and without this video i would never know how to do this lol. And i don't have a transmission code checker and i havent had it read either. This is our only vehicle and if this will fix it id rather do that than trade it in. Ill have it paid off in august lol
@obamitsui7795
@obamitsui7795 Жыл бұрын
I actually just figured out where the video description was lol. I feel dumb now lol
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
lol far from brother, dumb people dont try to save themselves money and this is one repair that will save you a BUNDLE of cash! Let me know if you have any questions about the repair and I will help accordingly. Thank you for watching!
@obamitsui7795
@obamitsui7795 Жыл бұрын
Thank you. I didn't expect you to respond so quickly. So thank you for that as well. Do you think this is probably the problem with it? I checked the fluid and it was normal color but had a burnt smell to it
@Relevantminded
@Relevantminded 2 жыл бұрын
Do you have to drain the transmission fluid to do this job?
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Yes
@kevinwaller6353
@kevinwaller6353 3 ай бұрын
I broke one of my bolts. Should I or can I remove the broken one with an easy out?
@Sellthoseflippingcars
@Sellthoseflippingcars 3 ай бұрын
Yes you need to extract it so you can put the new one in.
@kevinwaller6353
@kevinwaller6353 3 ай бұрын
@@Sellthoseflippingcars, I called the dealer to see if they had the bolt and the guy said holy macaroni, you're the first person to ever need that bolt. Off to the junkyard I go to pull one
@Sellthoseflippingcars
@Sellthoseflippingcars 3 ай бұрын
Yep, junkyard will probably save you $50 on that bolt alone, dealerships are a rip off
@kevinthomas8035
@kevinthomas8035 2 жыл бұрын
Do you need to program the tcm if it has one after this job?
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
No, the transmission will do a self-learn process. Remember though when you are refilling the transmission fluid to cycle through the gears when you get to the correct fluid level. You will feel the gears getting smoother and smoother each time you cycle through the gears. I do it 4 to 5 times to cycle all the fluid through.
@kevinthomas8035
@kevinthomas8035 2 жыл бұрын
@@Sellthoseflippingcars thank you so much thanks for the video
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
You are most welcome Kevin! Thank you for watching!
@kdeh21803
@kdeh21803 2 жыл бұрын
I don't have any transmission codes coming up on a 2011 T@C...... it "occasionally" acts as tho it does not want to shift from 3 to 4..... is that the pack?
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Yes that is the TCC on the fritz. Its cheaper just to replace valve body and pack at same time. Since TCC is apart of pack
@kdeh21803
@kdeh21803 2 жыл бұрын
​@@Sellthoseflippingcars Could it just be the "selenoid pack"?
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Yes it could
@kdeh21803
@kdeh21803 2 жыл бұрын
@@Sellthoseflippingcars so then it is hard to tell, so I guess it would be better to go ahead and replace the valve body and the TCC while I'm there just in case........
@andrewlozinak273
@andrewlozinak273 8 ай бұрын
I have a 2013 doge grand caravan thats stuck in limp mode. And its throwing a P0760 code overdrive solenoid contol circuit. Do you know which soliend this is or which one i have to change? The vehicle has 88,000 miles on it
@Sellthoseflippingcars
@Sellthoseflippingcars 8 ай бұрын
That would be shift solenoid c. But at the time of doing this repair I found that the entire solenoid block with valve body was cheaper than an individual solenoid.
@andrewlozinak273
@andrewlozinak273 8 ай бұрын
@@Sellthoseflippingcars thank you I will try to buy it that way
@Sellthoseflippingcars
@Sellthoseflippingcars 8 ай бұрын
I have the part linked in the video description
@Sellthoseflippingcars
@Sellthoseflippingcars 8 ай бұрын
Your welcome! Thanks for watching and stay tuned for more Auto knowledge videos here on the channel
@andrewlozinak273
@andrewlozinak273 8 ай бұрын
I just subscribed and liked . Thank you for all your knowledge and hard work
@kennethnorman5511
@kennethnorman5511 2 жыл бұрын
Thanks for the video. I just replaced the valve body/solenoid pack in my 2015 Dodge Grand Caravan. Everything seemed to go well, and there are no error codes, but now the Caravan won't shift out of park. What is the likely problem?
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Low transmission fluid. Do you have a transmission dipstick?
@kennethnorman5511
@kennethnorman5511 2 жыл бұрын
@@Sellthoseflippingcars Thanks for the quick reply. (I apologize for the delay in responding as I couldn't find the KZfaq video that I had asked the question in.) I do have an aftermarket dipstick to check the fluid with, and the level is just fine. I realize now that I should have been more specific. The gear shifter would not move at all. After I asked the question, I pushed the release just above the gear shifter, and the knob would then move, although it was hard to do so. According to the indicator on the dash, I was able to get it to move from park to reverse to neutral, and then back to park. However, when the gear shifter was all the way at the bottom where drive should be, the indicator on the dash said that the transmission was in neutral. It seems that that the gear shifter and the transmission range sensor are no longer in sync, but I'm not sure what to do from here. I have taken the valve body cover back off to check the position of the transmission range sensor, and I believe that it is in the correct position (it's in the slot farthest to the right, which I'm pretty sure was the position it was originally in). I did not move the cable on top of the transmission, so I don't think that's the problem. Any help would very much be appreciated.
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
I had that problem before, the valve body and shift cable are out of sync. Did you put lever on bottom of valve body on the same notch i did?
@kennethnorman5511
@kennethnorman5511 2 жыл бұрын
@@Sellthoseflippingcars I was thinking that must be the case. The lever at the bottom of my valve body is in the same position as it is at 13:17 in your video (all the way at the bottom or farthest back position), but I see that you placed the lever in a slightly different position at 24:08 (it appears to be up one notch from the bottom). Is that my problem? If so, do I need to take the valve body back out and reinstall it, or can I re-position it without taking it out again?
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
The lever has to be taken off and repositioned. Make sure not to move shift cable
@kishia1100
@kishia1100 2 жыл бұрын
Thanks so much for making this very informative video. I own a 2003 Dodge Grand Caravan Sport 3.8L V6 Front wheel drive. I went out to my van on Tuesday morning I cranked it up and I noticed I was feeling vibrations as I was sitting in the driver seat I let it run for about 5 minutes. When I put it in reverse and pressed on the gas the van cut out. I cranked it back up and put it in Drive and it cut out again. So I had my uncle come over and he hooked up a computer to my van and it said I had a misfire on 5. So I went to auto zone purchased new wires and spark plugs had those installed by my dad and that still didn't fix the problem. So my uncle came back drove my van forcefully. When he came back with the van it smelled like burning rubber. He put it back on the computer now it gave him codes for the transmission. Do you think that changing the part on my van that you changed in the video would help my van? Thank you.
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
What it sounds like is that you are having pressure problems. I have the same problem on a 2003 Dodge Caravan that I have right now and will be doing the repair on it soon as well. This is a common problem with MOPAR vehicles. This video would help you, although your transmission valve body is different than the one shown in the video. Same idea, just different valve body. I will be taking mine apart tomorrow if you would like, I can record it and have it online in 2 days. Would this help you?? Thank you for watching as well!!
@kishia1100
@kishia1100 2 жыл бұрын
@@Sellthoseflippingcars Omgoodness! Thank you so much for responding to my comment. I really appreciate you! And yes please I would love it if you'd make a video when you do the work on your van. Again thanks so much! I'll be looking forward to watching your videos.
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
You are most welcome! Sounds good I will plan for the video, it will be a fun one!
@kishia1100
@kishia1100 2 жыл бұрын
@@Sellthoseflippingcars Awesome!!
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
I removed the transmission valve body today from the 2003 Dodge Caravan. I will be editing the content tomorrow and should have it posted no later than Sunday.
@vincentrivest6235
@vincentrivest6235 9 ай бұрын
Yo my man , i just saw you video a few days ago , i got that issus whith my 2011 grand caravan, i am not sure if it is the body valve, when i put the car in drive it's stall, but it's still run in reverse . I was on the hiway when it has arrived, soon i got zero km the engine stop ? Like it was geared to hi . but like i said it works in reverse. What do you thinks ? Thanks in advance it will be very appreciated.
@Sellthoseflippingcars
@Sellthoseflippingcars 9 ай бұрын
Are you getting any engine codes?
@vincentrivest6235
@vincentrivest6235 9 ай бұрын
Hi Budy, thanks for answering's, well i asked my mechanic and he said no code ?? He said the transmission is done, because to expensive to repair, But i can do it my self for sure. You got a know that the car has 315000 km, but the rest was perfect, very well maintain, it's kind a sad to just do nothing . Thanks again.@@Sellthoseflippingcars
@Sellthoseflippingcars
@Sellthoseflippingcars 9 ай бұрын
I have a step by step video on the replacement of this transmission let me get the link for you brother. That will save you $4,000!
@Sellthoseflippingcars
@Sellthoseflippingcars 9 ай бұрын
kzfaq.info/get/bejne/ptFkdcaUq5PUl4k.html here you go, I found the replacement transmission at the junkyard on half off day, so I paid $100 for it. Look for a vehicle that has under 150,000 miles and service the filter before you install. This guide will save you SERIOUS CASH on this repair! Hit that super thanks for me and let me know if you have any questions during repair. I don't mind answering any questions you have
@vincentrivest6235
@vincentrivest6235 9 ай бұрын
I just checked prices , the body valve it' s expensive , dont you think that it could be the solenoid ?@@Sellthoseflippingcars
@legendarypestcontrol9722
@legendarypestcontrol9722 2 жыл бұрын
Could this fix my issues? My van keeps kicking me out of 6th gear back into neutral when going hwy speeds and redlines. Do not want to have to drop 3500+ for rebuild or new trans if I don't need to. Van is at 140K. mine is a 2011 Crew. Thanks.
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
I would love to say yes but to be for sure, it is time to drop your transmission fluid pan. If there are any metal chunks in there then you have a mechanical problem. If there is only metal glitter then you are okay (mechanically), you have a pressure problem. Which the pressure problem would be solved by this video, also have you received any transmission codes? Dont forget to subscribe, I always love helping my subscribers :)
@legendarypestcontrol9722
@legendarypestcontrol9722 2 жыл бұрын
@@Sellthoseflippingcars Yes just from AutoZone. Codes P0729 Gear Ratio Error in 6th, P0420 Catalyst System Efficiency below threshold, P0340 Camshaft Position Sensor Circuit- Bank 1 Sensor 1, C121C Torque request Signal Denied.
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
When is the last time you changed the engine oil? transmission oil and filter?
@legendarypestcontrol9722
@legendarypestcontrol9722 Жыл бұрын
I actually did fluid and filter change right after watching this video and it's still doing the same thing. I have been able to bypass 6th gear by just driving it in manual and never driving it over 5th gear. If I do drive it as normal around 5th/6th gear it kicks out of gear rpms read line and I can not excelerate I have to just take foot off gas and wait for rpms to come back down and it kicks/jurks back into gear or have to stop and kill engine and start again if it doesn't kick back into gear. I have been driving it in manual mode long enough at my check engine light has turned off. I'm thinking it's a computer issue since I have been able to bypass it acting up.
@legendarypestcontrol9722
@legendarypestcontrol9722 Жыл бұрын
I also had cam position sensor replaced when I had transmission fluid change. As far as I know the fluid that was changed was normal no large cuncks of metal in the fluid. Thank you for your help and previous responses.
@johng8967
@johng8967 2 жыл бұрын
I thought the engine coolant reservoir is on the left side. the window wiper fluid was near the transmission.
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
You are correct John
@walmartian348
@walmartian348 2 жыл бұрын
2016 R/T Caravan no codes showing runs fines other than a slight rough idle in park and drive and it surges during acceleration revs up to 2k rpm and back to 1k/1.5k rpm and runs fine after that
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Clean your IAC "Idle Air Controller" and your MAF "Mass Air Flow" Sensor. These can be found on your throttle body the MAF will be on the intake tube. Clean those and you should be good to go. Thank you for watching!
@walmartian348
@walmartian348 2 жыл бұрын
@@Sellthoseflippingcars thanks Ill give it a try
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Sounds good, let me know how it goes
@SLINGING_MUD_SINCE1994
@SLINGING_MUD_SINCE1994 Жыл бұрын
Amazing video
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Thank you brother! I am glad you enjoyed the video and found it beneficial!
@SLINGING_MUD_SINCE1994
@SLINGING_MUD_SINCE1994 Жыл бұрын
I no strange but is there anyway I can talk to you bro 🤣 I literally in the middle of taking out the pack I’m stuck on something
@SLINGING_MUD_SINCE1994
@SLINGING_MUD_SINCE1994 Жыл бұрын
I’m watching your video step buy step you miss a couple of steps buy talking about it and not showing I think that’s what really confused me
@SLINGING_MUD_SINCE1994
@SLINGING_MUD_SINCE1994 Жыл бұрын
Can you post the link one more time to be apart of your channel thanks
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
@@SLINGING_MUD_SINCE1994 kzfaq.info/love/o3SXInKTI8Wt-cB5mDQtWwjoin
@TDinosor47
@TDinosor47 3 жыл бұрын
2014 Oil accumulates on top of transmission housing just a little. Can you tell me where that oil is leaking? Thank you
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
That would be the vent on top of the transmission. Check your fluid levels. Make sure that the vehicle is running and is in park or neutral oh, the vehicle also has to be at operating temperature. To get a correct reading.
@enzodunn2577
@enzodunn2577 3 жыл бұрын
Oil cooler
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
@@enzodunn2577 you are entirely correct an oil cooler would prevent this valve body from failing! Great idea!
@enzodunn2577
@enzodunn2577 3 жыл бұрын
@@Sellthoseflippingcars that's is not what I said. When the oil cooler cracks it leaks down onto the top of the transmission and pools up. That can be why he was seeing oil on top of the transmission.
@enzodunn2577
@enzodunn2577 3 жыл бұрын
@@Sellthoseflippingcars there is hundreds of videos on KZfaq about this problem for the town and country and the grand caravan. So I would think that since he said oil, and not transmission fluid was pooling on top of his transmission, then maybe it is a GREAT idea to check the oil cooler.
@SLINGING_MUD_SINCE1994
@SLINGING_MUD_SINCE1994 Жыл бұрын
So I just bought this vehicle 2015 bro love your videos hoping you can help drove it then one morning nothing is working not reverse not drive not even the 2,3,4,5,6 won’t let me take it down to 1 🤷🏻‍♂️ like it’s in netural every single gear any recommendations
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Do you have any transmission codes coming up on your code reader? Thank you! I am glad you enjoy my videos! I am happy you find them beneficial with your vehicles upkeep.
@SLINGING_MUD_SINCE1994
@SLINGING_MUD_SINCE1994 Жыл бұрын
@@Sellthoseflippingcars yes sir I have a p-083B I change the fluid today and the filter and now I’n any gear when give it gas it moves after 5seconds of hard throttle
@SLINGING_MUD_SINCE1994
@SLINGING_MUD_SINCE1994 Жыл бұрын
@@Sellthoseflippingcars thank you for replying
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
@@SLINGING_MUD_SINCE1994 yep your fluid pressure sensor is on the fritz, time for a solenoid pack.
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
@@SLINGING_MUD_SINCE1994 you are most welcome! Let me know if you have any other questions
@greenlantern7537
@greenlantern7537 Жыл бұрын
What if your trans shift hard would it be valve body too
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
What transmission trouble codes are you getting? Yes it could be the valve body. Thank you for watching!
@greenlantern7537
@greenlantern7537 11 ай бұрын
@@Sellthoseflippingcars I brought it to the dealership and they told me the internal need repair and that the PCM is not responding also I might need a torque converter but I change the transmission filter and fluid and Thier was no pieces of metal so that why I have been watching your videos to learn what I can do
@FrankMixTutoriales
@FrankMixTutoriales 2 жыл бұрын
Hi I have a 2013 G Caravan 3.6 liter. And when I drive the van, the trasmition slept on 2g and then comes back normal. Can your tutorial fin my problem? And ir yes what's the name for the part
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
when is the last time you serviced your transmission? the parts for this repair can be found in the video description with a link to the part as well
@FrankMixTutoriales
@FrankMixTutoriales 2 жыл бұрын
@@Sellthoseflippingcars Yes sr I will and will share your video on music Chanel and Facebook :) Amd the thing is that I both the van 2 days ago. Can I do a flash on the transmission oil and filter first? To chale levels?
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
to check the transmission fluid levels properly on this vehicle you would need to have the transmission fluid dipstick which is linked in the video description if you do not have one. Make sure you are in park or neutral and the transmission needs to be at operating temperature. You did the service 2 days ago? Thank you for sharing my video as well!!!!
@FrankMixTutoriales
@FrankMixTutoriales 2 жыл бұрын
@@Sellthoseflippingcars No, sir. I have not done any service to the vehicle. I have purchased the vehicle two days ago.
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Oh ok, did you purchase it from a dealership? Because I would have them correct the problem to save you money. If not then it is time to check the color of the transmission fluid. It should be cherry red but in this case I believe yours is going to be pretty dark. That means the filter is stopped up and the fluid itself has no circulation so it is burning.
@zuberalisyed9786
@zuberalisyed9786 3 жыл бұрын
Hi good video and i like you careful attention, Can you advise what error code did you get to replace this. I get DC Error Codes P083B P0841 P0306 please help
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
I just saw this post, my apologies. Were you able to get your vehicle running?
@zuberalisyed9786
@zuberalisyed9786 3 жыл бұрын
@@Sellthoseflippingcars after replacing tranny oil and filter, oil filter adapter, tranny cooler lines and one tranny pressure input switch all the error codes were gone. The car is back up in running but i see hesitating going to 4/5 gear most likely the second tranny pressure switch will replace that as well
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
@@zuberalisyed9786 the 62TE transmission is not the best that MOPAR came out with.
@MandeepKumar-fh3jm
@MandeepKumar-fh3jm Ай бұрын
Hi dear I am having dodge grand caravan 2015 and having codes P0300 P0301 P0740 Can you help me with this Thank you
@Sellthoseflippingcars
@Sellthoseflippingcars Ай бұрын
You have two separate issues, P0300 and P0301 are misfires, when is the last time you have done a tune up to the engine? P0740 is your torque converter clutch solenoid malfunctioning and will need replaced. make sure to install a new transmission filter as well while you have the transmission pan off. Thanks for watching! Subscribe for more DIY Auto repair here on the channel!
@jhoniregis
@jhoniregis Жыл бұрын
I have a 2014 grand caravan, I have the code P1745 and P0868. After I cleaned the codes, just the P1745 camed back. I already replaced the kickdown solenoid and the Torque Converter Clutch Solenoid, but the problem was not solved. The car stay in the 3rd gear. I can reverse too. Please help me!
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
This is the reason I replaced the the valve body which includes all attached solenoids. The P1745 code is line pressure too high, this means you have an obstruction in your lines. This usually happens because the transmission filter is clogged and has let some debris thru, into your lines, causing the clog. It is time to flush your transmission valve body, I walked thru this process in the video when covering the small filter screens on the back of the valve body.
@jhoniregis
@jhoniregis Жыл бұрын
@@Sellthoseflippingcars I just found the problem. After hours working, the car show the code P0882. TCU low input. Was a relay. Just replaced, and working. Thanks!
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
@@jhoniregis That is great to hear Jhoni!! I am glad you were able to get your vehicle back up and running! Thank you for watching!
@jhoniregis
@jhoniregis Жыл бұрын
@@Sellthoseflippingcars I appreciate you help!
@RS-kz3gj
@RS-kz3gj Жыл бұрын
Could be an electrical problem.you need someone that's very good and tracing down the problem.Iv seen this happen before on that code
@brandonmcintosh9575
@brandonmcintosh9575 Жыл бұрын
Update: got it all replaced and it's still not moving. Still seems like the transmission is stuck in neutral. I don't know why. Could it be the TCM?
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Did you use your transmission dipstick to check your fluid level? The 62TE is a very sensitive transmission and needs the proper level of fluid. Also remember to cycle thru the gears after you fill the transmission fluid. Thank you for watching!
@brandonmcintosh9575
@brandonmcintosh9575 Жыл бұрын
Ya I have the fluid level at the correct amount and I cycle thru the gears but the transmission isn't actually shifting through them for me. I didn't know if there would be away to reset all the TCM or cars computer to have it realize there is a new valve body in there
@Guy_On_The_Couch
@Guy_On_The_Couch 3 жыл бұрын
I have a code p1745 on a 2013 grand caravan and thought to change out the Pressure Control (EPC) Solenoid. I did have the code for P0868 as well. But I cleared that and hasnt come back since. Right now its stuck in Limp mode. Not sure what to fix now since watching this video.
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
P1745 on your 2013 Grand Caravan means that the transmission pressure has been too high for too long. The pressure control solenoid you are speaking of replacing will be on the valve body as shown in the video. Depending on the price of a solenoid you are trying to replace, sometimes it will be cheaper just to replace the valve body.
@Guy_On_The_Couch
@Guy_On_The_Couch 3 жыл бұрын
@@Sellthoseflippingcars Its $200 something on RockAuto. And the whole Valve body (complete) is $700. But If that doesn't fix my problem then I have to take it apart again. I've been having problems with the tranny all year. Just don't drive it much. It slips sometimes. Sometimes it would shift hard. I replaced the tranny fluid when i did the coolant lines. My question is do you think I should just replace the whole Valve body or just do the pressure control solenoid?
@Guy_On_The_Couch
@Guy_On_The_Couch 3 жыл бұрын
@@Sellthoseflippingcars Also do I need to program this once done? It is in Limp mode now.
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
www.etsy.com/au/listing/783939277/62te-6-speed-transmission-valve-body that is the valve body that I order for my 62TE transmission valve body replacement. I have ordered a few from them and they are remanufactured units but come with a warranty and save you a bundle
@Guy_On_The_Couch
@Guy_On_The_Couch 3 жыл бұрын
@@Sellthoseflippingcars Thank you for the fast responses. I want to get the whole thing with everything on it. The one on RockAuto has the pressure control solenoid and the tcc.
@Relevantminded
@Relevantminded Ай бұрын
Will doing this fix my P1745 and p0868 on my 2014 dodge grand Caravan? Apparently i have both low and high line pressure im assuming that means the transmission coolant lines maybe and it hard shifts into reverse and drive and when im driving i think its in limp mode.
@Sellthoseflippingcars
@Sellthoseflippingcars 23 күн бұрын
Yes, the valve block is blocked and is causing your pressure problems. parts are listed in the description and dont forget to put a new transmission filter on while you are in there. Let me know if you have any questions during repair. Thanks for watching!
@Relevantminded
@Relevantminded 23 күн бұрын
@Sellthoseflippingcars so just the valve body or the Solenoid too?
@clintrittenhouse2782
@clintrittenhouse2782 3 жыл бұрын
I’m working on a 2012 town and country with code P0765. How do you know if it’s the solenoid or the valve body?
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
I replace the entire valve body because it is much cheaper than to find the TCC solenoid by itself. I just purchased one the other day for a 2008 Dodge Grand Caravan and it cost me $200.
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
Also my apologies Clint it took me a couple days to respond I have been really swamped lately
@jamest3039
@jamest3039 11 ай бұрын
What ended up being the problem from the P0765 code?
@chrisloveall2821
@chrisloveall2821 2 жыл бұрын
Do you have to replace the valve body gasket or can you reuse the same one when doing this project
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Yes, remember the gaskets that are in there are probably the originals from the factory. Thank you for watching
@_Shayne
@_Shayne 3 жыл бұрын
Does the Vehicle need to be programmed afterwards ?
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
No it will do a self learn process that you do not have to initiate.
@_Shayne
@_Shayne 3 жыл бұрын
@@Sellthoseflippingcars thank you sir!! I'll give it a go 🤞
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
You are most welcome Shayne!
@Relevantminded
@Relevantminded 23 күн бұрын
Do you push in or down on the lower part of that connector?
@Sellthoseflippingcars
@Sellthoseflippingcars 23 күн бұрын
which connector?
@Relevantminded
@Relevantminded 23 күн бұрын
@Sellthoseflippingcars the big one on the front transmission pan I think for the shift Solenoid
@Relevantminded
@Relevantminded 16 күн бұрын
@Sellthoseflippingcars Nevermind I figured it out and luckily it came off without breaking it ow I'm working on testing the pins on the solenoid to see if it's the issue before removing the whole valve body.
@runningbear1982
@runningbear1982 2 жыл бұрын
Great video. That being said I said fuck it and I bought a remanufactured transmission. 🤣
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Thank you! Thanks for watching!! Great choice on the reman transmission! This transmission is not bad to replace here is the video I recorded on replacing the transmission. Hope it helps! kzfaq.info/get/bejne/ptFkdcaUq5PUl4k.html Have a Merry Christmas and a Happy New years!
@MrDumonic
@MrDumonic 2 жыл бұрын
Next thing I need done is the oil cooler filter housing. They want $1300!!! I’m gonna take it to a regular garage where they charge less per hour. If only I had the tools and time to do it. But for the transmission, I wanted professionals dealing with it that know these vehicles inside and out. I don’t mind paying to have it done right and under warranty.
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
Understandable, still a high price though lol
@juanpablomgonzalez
@juanpablomgonzalez Ай бұрын
Please someone help me after we install the valve body I got a code of p2764
@Sellthoseflippingcars
@Sellthoseflippingcars Ай бұрын
Double check that the harness plug for the solenoids is seated properly and has a flush connection. P2764 shows that your voltage is low to that solenoid.
@amrabdalla5673
@amrabdalla5673 2 жыл бұрын
the best thing to do is reuse the trans oil if it’s never been drained or got some miles on it look it up
@Sellthoseflippingcars
@Sellthoseflippingcars 2 жыл бұрын
That is like saying its ok to reuse your engine oil after its been used. I am teaching the proper way not the way that will get you by. I guarantee you that dealerships do not reuse the oil they just drained. But you do you
@AJ-bf6dp
@AJ-bf6dp Жыл бұрын
I may of missed it, but what are all the o-ring sizes?
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
The O-rings I used were in a universal o-ring kit, I can link the kit to you if you like.
@AJ-bf6dp
@AJ-bf6dp Жыл бұрын
@@Sellthoseflippingcars holy crap that was a quick reply! Yes please and thank you!
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
@@AJ-bf6dp Always trying to help you get back on the road quicker without breaking the bank, even on my birthday. Heres the link you requested amzn.to/3r26XXB Let me know if I can be of any further assistance
@AJ-bf6dp
@AJ-bf6dp Жыл бұрын
@@Sellthoseflippingcars happy happy happy birthday! And thank you again.
@Sellthoseflippingcars
@Sellthoseflippingcars Жыл бұрын
Thank you 😊 and you are most welcome! Make sure u subscribe for more DIY Auto and thank you for watching
@TDinosor47
@TDinosor47 3 жыл бұрын
I wander why all Caravans transmission solenoid are gone in every junkyards where I live.
@Sellthoseflippingcars
@Sellthoseflippingcars 3 жыл бұрын
It is one of the largest selling minivans in production. Awesome for sales bad for parts
2008 Dodge Grand Caravan 62TE Transmission Replacement made Easy
18:21
Sell Those Flipping Cars
Рет қаралды 30 М.
Chrysler 62TE Solenoid Pack Replacement PART 1
18:38
MotorCity Mechanic
Рет қаралды 296 М.
HAPPY BIRTHDAY @mozabrick 🎉 #cat #funny
00:36
SOFIADELMONSTRO
Рет қаралды 17 МЛН
Женская драка в Кызылорде
00:53
AIRAN
Рет қаралды 385 М.
Became invisible for one day!  #funny #wednesday #memes
00:25
Watch Me
Рет қаралды 60 МЛН
The Truth About Dodge Grand Caravans
10:32
Scotty Kilmer
Рет қаралды 408 М.
500,000 Mile 62TE
46:45
Gary Ferraro
Рет қаралды 94 М.
Chrysler/VW 62TE Transmission Solenoid Pack Testing
12:08
MotorCity Mechanic
Рет қаралды 56 М.
Caravan / Town & Country 62TE Transmission Dipstick Hack
8:05
South Main Auto LLC
Рет қаралды 775 М.
2014 Dodge Grand Caravan 62TE Transmission Shift Solenoid (Minute Maintenance)
35:01
Clearing up common misconceptions about the Chrysler 62TE
6:35
Transmission Digest
Рет қаралды 20 М.
Video testing solenoid 2 different tcm - good and bad one
1:34
Muhammad Anwar
Рет қаралды 99 М.
БМВ i4
0:29
Vladione
Рет қаралды 1,8 МЛН
ride like a god... #bike #bikelover #biker #rider #motorcycle #india
0:10
КИТАЙСКИЙ АВТО
0:19
Films
Рет қаралды 1,5 МЛН