2013 Renault Master 2.3 dCi Front brake discs and pads Replacement

Рет қаралды 20,842

Күн бұрын

Please note the upper slide pin rubber boot was not refitted on this side because it was damaged and was replaced later! 😁

Пікірлер: 41

@markwilliams2830 3 жыл бұрын

Very good info and well executed Max.I'm sure your arm muscles are getting bigger .All those high torque bolts!

@maxautouk 3 жыл бұрын

Bigger muscles or worn out elbows!! Thanks for the comment 😃

@ImranFamily2255 8 ай бұрын

Very helpful video ❤ I m really recommend this channel

@maxautouk 8 ай бұрын

Thanks for the comment 😃

@frednetherlands887 2 жыл бұрын

Thank you!

@maxautouk 2 жыл бұрын

You’re welcome thanks for the comment

@bmwmotorsportm5 Жыл бұрын

Thanks you sir for the good video and good job. I know tools now, I prepared tools and go job. I broke the two brake caliper bolts. 😢 💪👏👏

@maxautouk Жыл бұрын

Glad I could help with the video and I hope you got it sorted!

@bmwmotorsportm5 Жыл бұрын

@@maxautouk Thanks sir ! 🍺😃

@maxautouk Жыл бұрын

💪🏽

@bigdosser7777 7 ай бұрын

Thanks for the video, I like doing stuff on my own cars as I know exactly what has been done. I have seen others doing brakes before and they didn't bother cleaning or greasing anything, just put the discs on and slotted the pads in. Looking to swap discs and pads on my 2018 master, I was surprised to see Brembo listed as an option although they are a lot more expensive. Couple of questions mate, did you put some copper grease on the back of the pads? and was the pins also greased? Not a criticism just a question

@maxautouk 7 ай бұрын

Yeah any grease that isn’t solvent based or abrasive (so not multipurpose grease or copper grease) is ok for the slide pins and I use red rubber grease or aqua slip grease against the ears of the caliper and the face of the piston so that it keeps the pre mainly clean on the backsides so they don’t build up too much brake dust

@gerarduspoppel2831 6 ай бұрын

A lot of people forget to grease it up. You could also spray that Tork 40 in with WD40 the day before. Do it will come loose a lot easier.

@maxautouk 6 ай бұрын

Great tip!

@Oh-Jay52 3 жыл бұрын

Brembo Calipers ? wow , nIce ..

@maxautouk 3 жыл бұрын

I was surprised as well!

@MrDavedraver888 8 ай бұрын

Great video, Max. I've gotta do my front pads but struggling with the hex size as my 8mm hex looks way to small , am I missing something as you mention it's a hex 8 ?

@maxautouk 8 ай бұрын

It’s been so long since I’ve done front brakes on a Renault I honestly can’t recall… it is a large size though for sure

@themechanic7561 3 жыл бұрын

Only criticism unless I couldn’t see it, did you have an axle stand under there just in case. I’ve had a jack fail before ,and when you re -fitted the caliper the top dust boot for the slider pin was missing 👍🏻

@maxautouk 3 жыл бұрын

Well spotted! Yeah I always put a stand under the subframe which is quite far in on these - nicely spotted with the upper boot, the old one was ripped and spring inside had flown off somewhere so I sent it off without one for a few days until it arrived and I can assure you it’s all good now 😃 thanks for the comment!!

@themechanic7561 3 жыл бұрын

@@maxautouk glad you had a stand underneath 👍🏻. Yeah been in the trade 20 years gives u a bit of an eagle eye! Look forward to your next video 👍🏻

@jeremycanning8934 6 ай бұрын

you forgot to fit the upper slide bolt seal

@maxautouk 6 ай бұрын

Good eye, it’s in the video description 👌🏽the boot was torn so I refitted it as is for a day or two while the new one was on order

@stephenhall7892 2 жыл бұрын

New tyre next 😂😂good job

@maxautouk 2 жыл бұрын

Thanks for the comment! Yep it has a new tyre too off camera 😁

@michaelunison7607 2 жыл бұрын

Nice job. Appreciate you doing this video. You said 190 Newton meters for the carrier bolts? I was struggling wether its 119 or 190. NM's, kept playing it over & over. What are the NM 's for the caliper bolts? And are the rear ones same as front for tightness? My owner manual said 172 NM for standard wheel lug bolts for 2014 Renault Master X62 . But have nothing in way of shop info or specs. Did you find a shop manual? I'd love to find info on where i could get one. I have one video of front accident repair. Many other videos to put up, but finding time to get them uploaded? But I intend to contribute more. Wouldn't the paint at beginning of video just burn off from heat of disk? I'm interested in that idea. As I think your right about rust damaging them. What is the name of what you sprayed on them?

@maxautouk 2 жыл бұрын

Hi there they are 190nm yes! Very tight!!

@lloydgore8860 Жыл бұрын

Where are you getting your torque setting values from? I'd like a service manual for myself ideally.

@maxautouk Жыл бұрын

Because I run a garage I pay for access for main dealer information through e3 technical. Haynes manuals are probably the next best most easily accessible thing but I do find for most cars older than ten years you can find a main dealer workshop manual online somewhere for free to download if you're persistent enough

@doudou82vivaldi 2 жыл бұрын

Bonjour Est ce que le système de freinage est le même que pour un master renault dti 2.8 Merci

@maxautouk 2 жыл бұрын

My apologies I don't speak French

@timthomas4339 Жыл бұрын

Hi whats the nm on the slider bolts please

@maxautouk 11 ай бұрын

A whopping 75nm!

@timthomas4339 11 ай бұрын

Nice one cheers bud👍

@maxautouk 10 ай бұрын

Anytime

@kamilosPL19 Жыл бұрын

Im not specialist..... but where did u lost guide rubber? u know that is serious mistake right?

@maxautouk Жыл бұрын

Thanks for the comment, well spotted Yes the boot was ripped and when I removed the pin it completely tore apart, I ordered and fitted a new boot later off camera 👍🏽 if you leave the pins without boots for more than a day or two they will seize and destroy your pads and discs

@stevereddish6901 Жыл бұрын

No rubber on top slider. Will be seized in no time

@maxautouk Жыл бұрын

Well spotted 😁👍🏽 the old one was badly damaged and I couldn’t get one the same day but it was sorted a day or so later, thanks for the comment

@robertanderson2142 Жыл бұрын

Shoddy job you lost the top slider rubber

@maxautouk Жыл бұрын

Well spotted, it was badly torn so I threw it away and put a new one on a few days later but since I already had the camera out I continued with making the video 😁