2015 Volvo V40 1.6D Injector replacement

Рет қаралды 23,820

Жыл бұрын

Step by step guide on how to replace the fuel injector on a 2015 Volvo v40 1.6 diesel engine. Same procedure applies for the injector replacement on this 1.6d in various other Volvo models. Includes adaption procedure. P1264 Cylinder 4 high to low side short fault code was stored relating in Injector number 4. P0201, P0202, P0203, P0204, P1261, p1262 & P1263 are common fault codes that may also be stored.
Any Donations to help Support my Channel are much appreciated.
Donate via Paypal - paypal.me/diydaly
Check Euro car parts - tidd.ly/3lIO7xA (use discount codes on site)
New Fuel injector Ebay - ebay.us/ybkDI7
Diagnostic machine used in this video:
Topdon Phoenix lite 2 - diydaly.co.uk/products/phoeni...
Tools used:
Milwaukee 3/8 impact driver - ebay.us/ZtxrBu
Socket set - ebay.us/7tUKdM
Digital Torque wrench - amzn.to/34kpI9y
Torque Wrench - amzn.to/2VZ4CKu
E-Torx sockets - ebay.us/5a3i3Y
Screwdriver set - amzn.to/30RA53L
Spanner set - amzn.to/2DlwUZm
Injector cleaning set - amzn.to/3grvnPB
Injector seal removal tool - amzn.to/2O9d7P7
Ring Inspection Lamp - amzn.to/3gGWHcG
Bonnet lamp - ebay.us/3y0gGv
Injector clamp bolt torque setting:
stage 1 - 4NM
stage 2 - 65 degrees
Useful links:
Car Analytics - Vehicle information checker - tidd.ly/3B2PEbx
If you found this video useful, please Like Share and Subscribe to help grow the channel, and never miss any future content. kzfaq.info?...
Please also check out my website - www.diydaly.co.uk where you'll find top quality goods, tried, tested and recommended by actual mechanics.
DISCLAIMER: Links included in this description might be affiliate links. If you purchase a product or service with the links that I provide I may receive a small commission. This doesn't effect the price you pay!

Пікірлер: 64

@diydaly Жыл бұрын

New Fuel injector Ebay - ebay.us/ybkDI7 Diagnostic machine used in this video: Topdon Phoenix lite 2 Ebay - ebay.us/tsyiTI Topdon Phoenix lite 2 Amazon - amzn.to/3dxuQQl Tools used: Milwaukee 3/8 impact driver - ebay.us/ZtxrBu Socket set - ebay.us/7tUKdM Digital Torque wrench - amzn.to/34kpI9y Torque Wrench - amzn.to/2VZ4CKu E-Torx sockets - ebay.us/5a3i3Y Screwdriver set - amzn.to/30RA53L Spanner set - amzn.to/2DlwUZm Injector cleaning set - amzn.to/3grvnPB Injector seal removal tool - amzn.to/2O9d7P7 Ring Inspection Lamp - amzn.to/3gGWHcG Bonnet lamp - ebay.us/3y0gGv Injector clamp bolt torque setting: stage 1 - 4NM stage 2 - 65 degrees

@sheffcitys2forgedinsteel255 Жыл бұрын

Hi mate, Just a quick question for you, I have a volvo V40 D4 r design 2.0 diesel year 2014, now i seem to be going through oil quite a bit, I've been looking for weeks every morning for oil on the road where I park and nothing they no smoke coming from anywhere at all running fine, Just can't figure out where it's going. Any help would be appreciated

@diydaly Жыл бұрын

@@sheffcitys2forgedinsteel255 may be burning it , dactyl how much is it using , how much per how many Miles roughly

@sheffcitys2forgedinsteel255 Жыл бұрын

@DIYDaly every few weeks it asks for half a litre to 1 litre as it's not a manual dip stick it's electric one, What you mean burning it,? How, and why, and solution

@diydaly Жыл бұрын

@@sheffcitys2forgedinsteel255 so much will pass through and get burnt up as it’s passes through the exhaust .. these engines arnt know for excess oil consumption though , you need to get it checked really . There’s a possibility the turbos failed or a leak in the intake system and it’s dragging the oil into the intake ..

@sheffcitys2forgedinsteel255 Жыл бұрын

@DIYDaly if the turbo had gone tho wouldn't it be kicking out smoke through the exhaust? And it's been like this for a year now and apart from not knowing where the oil is going it runs and drives fine no loss of power, Very very strange.

@sollykhan2385 6 ай бұрын

Thank you for this AWESOME tutorial, very helpful, please post more, the handy dandy links for them tools and equipment is very valuable, Cheers 🙂

@diydaly 6 ай бұрын

More to come! Thanks for the comment

@kevinpalmer7452 Жыл бұрын

Great video Those V40’s ain’t a bad car Ford underpinnings and PSA Engines a nice drive and well made. I see the Top Dons still earning its keep.

@diydaly Жыл бұрын

Yeah I like em tbf, I really fancy an XC60 D5 at the mo but gota get some funds together first! 😬 .. Yeah Topdon still going strong.. its my "go to" machine now.. still got the snap on but its mega slow.. I still haven't found anything that the topdon can't do compared to the snap on (other than ours has a scope!)

@user-op8cy5fu3l 8 ай бұрын

Great video very helpful Especially listing torque settings tools needed etc Thanks for your efforts to help people

@diydaly 8 ай бұрын

Glad to help 👍👍

@user-op8cy5fu3l 8 ай бұрын

Quick question I’ve just removed my original injectors and they have a small plastic sleeve around them the new genuine ones don’t do you know if you have to remove that sleeve from the original and put it on the new one Tia

@diydaly 8 ай бұрын

@@user-op8cy5fu3l yes you should swop it over mate

@kristalydaniel3113 8 ай бұрын

You are legend @diyDaily thank you somuch for the videos very informative

@diydaly 8 ай бұрын

👍👍

@andriusmboandrej3759 6 ай бұрын

Спасибо большое. Вы мне очень помогли. Я из Беларуси. Спасибо

@diydaly 6 ай бұрын

👍👍

@ioandriment3140 Жыл бұрын

Super lesson. Many thanks. It's helpful. All the best. I hope this is the same for Ford Galaxy 1.6 diesel 2012.

@diydaly Жыл бұрын

👍👍 glad you enjoyed it

@TheDervMan Жыл бұрын

That’s an impressive torque wrench compared to mine at least 😎👌🏻🔧

@diydaly Жыл бұрын

haha there a mega bit of kit tbf! bit wedgy though!! 😬

@cw2126 Жыл бұрын

Great video lad 🔧🚘

@diydaly Жыл бұрын

Thanks 👍

@BlakeCDS 7 ай бұрын

Replaced copper seals on this engine today due to fumes in cabin. Noticed a leak off pipe clip only had 1 tab instead of 2, could this cause the fume smell inside the cabin? Keep up the great work you're videos have been a lot of help to me

@diydaly 7 ай бұрын

👍 should be ok if it’s not leaking fuel still

@ionelcocosatu2849 4 ай бұрын

hi, what symptoms did the car have before the injector change?

@lovepreetsinghhanjra1997 Жыл бұрын

Nic work sir 🔧

@diydaly Жыл бұрын

Thanks as always 👍 👍

@ewawa5253 Жыл бұрын

I pulled them out by hand on my engine

@joelmerd6864 26 күн бұрын

Great video, very helpful! I have a S40 2012 with the same engine, that needs injector replacement due to short circuit. Do I have to lubricate the body of the new injector before fitting it in? (The old one was very corroded for some reason)

@diydaly 14 күн бұрын

Neh just clean the hole out well & the seat

@dimonedimone6228 3 ай бұрын

Hello Good video 👍 Maybe u must write number of injector? And reset adaptation of 4th cylinder?

@diydaly 2 ай бұрын

Yes needs to be adapted mate

@user-xy2lb9df4i Жыл бұрын

Today I replaced an injector on my 2015 v40 D2, your video was great guidance.Thanks! I noticed that on the car you worked on the dashboard shows: "ESC termporarily off". I had exactly the same dashboard message before replacing the injector. After replacing the injector it changed into: "City safety service required'. Any idea what this could be? Thanks in advance!

@diydaly Жыл бұрын

Thanks for the comment , tbh I’ve never seen that message before , have you done a full code scan after? Presumed it should have some sort of fault code relating to it

@skylarkfieldfarm Жыл бұрын

I have a faulty injector. And the same esc message. Can't be a coincidence.

@wesleydillon86 Жыл бұрын

Very helpful video. Iv a 2013 Ford focus 1.6 tdci and I'm getting code P029A cylinder 1 balance - fuel trim at max. Is this injector going bad, car has rough idle and it is very jumpy at low rpm seems down on power aswel

@diydaly Жыл бұрын

Thanks 👍 yeah im fairly sure thats the injector

@wesleydillon86 Жыл бұрын

@@diydaly Thanks for the reply. I'll pick up a new injector and give it a go, hopefully it sorts it. 👍

@PietroEnciu Жыл бұрын

Those injectors must be coded into the ECU. I did the coding with a TEXA scanner and then did the adaption.

@diydaly Жыл бұрын

Thanks for the comment

@mihaidanielpatrichi4364 9 ай бұрын

Out of sheer curiosity, how many work hours would be normally billed for removing all 4, checking and putting them all back in?

@diydaly 9 ай бұрын

2-3 hours

@peteralty5 7 ай бұрын

Nice presentation but to be complete you havent added the process for allowing the ecu to set parameters and to learn the new injector . Can you post me the procedure please

@diydaly 7 ай бұрын

The procdure can only be done on a diagnostic machine mate

@peteralty5 7 ай бұрын

@@diydaly thank you .thats is very helpful . And thank you for your quick response all the best

@krazdy8119 6 ай бұрын

Hey, just wondering what the yellow band around the diesel injector you pulled out is for. I saw that it was not on the one you put back in, and I am just wondering if it is necessary, or if it works without. I have removed mine, and it has a similar band around it in white. The new one I am going to put back in does not have one. Did you put one on before you put the new one in, or is it not necessary?

@diydaly 6 ай бұрын

You can get away without it , it’s a locating guide to keep it nice and square

@krazdy8119 6 ай бұрын

@@diydaly Thanks so much! This was very helpful. Nice video!

@andreipari4646 11 ай бұрын

Hi there, on my s40 1.6D 2011, i had the 4th injector faulty been changed in garage with an new one, but when i picked the car up, when is accelerated has an tapping noise comming from engine/injector can't notice exactly from where. It this happened to someone or anyone knows the reason / any tips. Diagnostic has no fault found i don't know if injector been coded but my friend couldn't see that function on his snap on diagnostic tool. I been back with the car to the garage and they said can be from DPF but i don't see the sense cuz havw no fault and before the injector faulty engine been smoothly.

@diydaly 11 ай бұрын

Some times the injectors are quite tappy until configured correctly .. could be diesel knock