+6" Apache Bagger install using stock brake, clutch and electrical.
Пікірлер: 57
@blueskyguy54152 ай бұрын
Best "How-to" video I've ever viewed!
@davenine50072 жыл бұрын
Hello, Thank you so much for taking the time to post this video - saved me $400 in labor $$ !
@RazorbackRandall Жыл бұрын
I did it! 🎉 It took about 6-7 hours of work but that’s typical for me bc of second guessing myself. I kept going back and rewatching each piece as I went so the time line is on me. I didn’t have the work space either so I was make shifting that. Ultimately this video saved me about $600- $750 on my Indian shop installing. Word of advice to everyone on the 2020 Roadmaster Dark Horse, the plug that he mentions that goes to the handlebars, it is the one he’s talking about on the left (when facing the bike) but it’s ran through the metal frame to the fairing housing and is zip tied behind it. Remove the right blinker, take the 3 screws out of the fairing plastics on the back & use the needle nose players to twist off the zip tie. You can then pull the whole handlebar harness out of the front. You’ll be relocating that to the top in the middle somewhere bc it likely doesn’t reach back to the original location. Don’t second guess it like me. I have no idea where the ambient air sensor plug came from but it’s got the clip to stick back into the frame somewhere but I can’t find it. No idea how or why I pulled it out.
@wendelltolliver2798 Жыл бұрын
I was about to go to dealer and get bars put on but after seeing your great video I know I can do this myself. Thank you so much
@kstkustoms1324 Жыл бұрын
That’s what it’s for my man! Keep that money in your pocket. My cell is 678-378-5036 if you need assistance
@michaelroberts88322 жыл бұрын
Excellent! One of the best how to videos I've ever seen. Very smooth as you take us through the process.
@steveh4564 Жыл бұрын
My shop quoted $165 per hour for 4-5 hours! Thanks to this comprehensive install video i'm bolting on my new 6" Apache Baggers (shipped like grease lighting by the way) on my 2021 Chieftain Dark Horse in my garage as we speak. I smeared a little dielectric grease on the taped up portion of my pull wire to make that sharp bend go a little smoother on the bulky throttle side. Thanks!
@speedypatriot5211Ай бұрын
Excellent how-to. Thanks! I'm actually putting stock bars back on, but it's the same process.
@GCACok2 жыл бұрын
Bought and installed these. Totally changed the bike and the video completely helped with the install. ⭐️⭐️⭐️⭐️⭐️
@adamcouri1514 Жыл бұрын
Just want to thank you for the video. This was an amazing help. I installed the 8" Klockwerks Ergo bars on my 2018 CDH. It took me a total of about 3 hours. The worst part was the right side wiring through the bars....after that, it was a snap. Thanks, Adam
@Rezaroth3 жыл бұрын
Thank you for all the effort you guys put in this video. Very detailed. I was a bit surprised that the new handle bars cover a bit of the gauges.
@usmcesu6 Жыл бұрын
Thank you for the video. You made it so easy. I can’t believe I did it all by myself with your video. 👍🏼
@speedstersa4 ай бұрын
This was a fabulous how to video. With the info in your video I was able to install new KST bars on my new 2024 Indian Chieftain Dark Horse. And with the money I saved doing it myself this video convinced me to go buy a DeWalt cordless ratchet.
@dewaynewadsworth32303 ай бұрын
Just bought a 2024 roadmaster darkhorse. Dealer said fairing has to come off completely. We dont have that front chrome cover like in this vid. Did you have to pull alot off to get to everything?
@RayTrain19712 жыл бұрын
Thank you Ret and team for this awesome video, well done and thorough. I installed the +6 Apache Baggers on my 2020 Roadmaster Dark Horse, took just under 5 hours to complete. It went exactly as the video, other than having to take the front fairing off because of the smaller headlight. Thank you again for the great video and the badass bars!
@bradrichardson80203 жыл бұрын
Ive watched alot of How to Videos, and yours is Excellent! Makes me wanna go out and buy 6" bars for my 2019 Roadmaster! Thanks!
@Mrdavethomas12 жыл бұрын
Great video. Excellent step by step. One not, I have a 2019 Chieftain Dark Horse and I had to remove the fairing cover to access the wiring harness.
@ThumbBlaster2 жыл бұрын
Got 6” on step by step. Thanks for the vid
@davidguy25733 жыл бұрын
Got a 17 chieftain and learned a lot, thank you
@davidguy25733 жыл бұрын
I’m right in the 17 chieftain limited and this video helped a lot thank you very much
@521483332 жыл бұрын
Very good detail in this video I followed this and changed mine in 4 hours going slow and checking video often
@MontaleoneFamily Жыл бұрын
Great video. Pulling the wires through is a bear.. got about 2 hours into the wiring now... Trying to figure out how to get past where the wires get stuck. Tempted to remove the ends and try again.
@aajalapeno6492 жыл бұрын
Finally got mine installed today. 2020 Roadmaster Dark Horse, the wiring in the faring was very different because it was all clamped and zip tied together with a small window to work out of. About 7 hour project at the end of the day.
@RazorbackRandall Жыл бұрын
Me too. Just bc second guessing myself on why I couldn’t get the handle bar wiring harness out as easy as he did. Zip tied behind that bar so need to undo the bottom of the fairing from the backside to clip that zip tie.
@vagabondxxx2 жыл бұрын
Woww! Super mechanic. Very well explained
@jeffallen52793 жыл бұрын
Very thorough,thank you
@billpavarotti26942 жыл бұрын
Just did a 17 Roadmaster yesterday and it surely didn’t go as smooth as your install! The 17 had soldered connections at the switch housings so the wires need to be pulled up through leaving the housing intact. The wiring left through after the install is really short and the wiring needs to moved around inside the fairing a bit. The clutch cable need to be rerouted too. It all come together but not as simple as the video. That being said, I’ve done many Harleys and this install is still way better than having to change clutch and brake lines!
@carynbenckert42115 ай бұрын
I love how the local dealer service dept is saying this install is gonna take them multiple hours to accomplish.
@richardcaruso002Ай бұрын
It's not, it's called flat rate.
@kjpoplawski3 жыл бұрын
Thank you 👍👍👍👍
@4wd353 жыл бұрын
Great video
@aaronkershaw21073 жыл бұрын
Great video, Thank you. Do you guys sell the longer clutch and brake cable for the 10" bars?
@darronmorris2683Ай бұрын
Nice video
@thierrypoirey4439 Жыл бұрын
Thank you so much ! Very clear and complete. I would like to change my bar on my 2016 RM, and after checking the connections on the handle, I saw there are not the same and not so easy or impossible to disconnected there !! Any other solutions ? Thank you for your help from France. Few year ago, I have done the same job on my HD Road King, I mean I should be able to change it myself... Thierry
@sukhipandher90902 жыл бұрын
Quick question can you not remove the bars with the wiring intact. Because when your installing the new bars. U r still feeding the wires in and out thru the headlight
@indianjoe20752 жыл бұрын
Had you installed heated grips bed I just bought some heated grips for my 2017 chieftain and I know the bars aren’t pre wired and I have the harness that run through the bars just wondering if I have to remove the whole front of the fairing to run them through the bars
@brianmarvel181018 күн бұрын
Ill guess all the torque numbers are in paper instructions?
@tugmaster19622 жыл бұрын
Hey bro was plastic stripped of 12 ga copper are did it have insulation on it
@6.0hhh2 жыл бұрын
we tightened everything down as far as the bars go but the bars are loose I can move them down with pressure?
@DJackson18822 жыл бұрын
Started doing my +6” on my 17 Roadmaster, how much wire is exposed at the base of the bars?
@montr68682 жыл бұрын
Is this part available?
@jasonsousa452211 ай бұрын
I am just installing heated grips and contemplating pulling all the wires out and restringing it rather than trying to pull the heat grip harness. Can you pull all wires at once?
@kstkustoms132411 ай бұрын
If you own an Indian, the heated grips are east peazy. They just plug right into the housing, nothing goes thru the bar
@jasonsousa452211 ай бұрын
@@kstkustoms1324 Unfortunately the 2017 was not prewired. I followed your video and it was easy. Just removed all wires and pulled them through. Not as hard as I thought other than stripping the torx bolts on the brake,clutch c clamps. 😫
@carynbenckert42114 ай бұрын
what ratchet adapters/bits are you using for this job?
@kstkustoms13244 ай бұрын
Milwaukee right angle ratchet. Just standard socket bits
@jr77192 жыл бұрын
What kind of wrench are you using.
@Mrdavethomas12 жыл бұрын
It’s a Milwaukie M12 socket driver. Awesome tool!
@RazorbackRandall Жыл бұрын
I bought the same ratchet driver from Lowe’s on Father’s Day special. Buy the 2 pack battery’s for $99 & get the tool of your choice. This was one!
@prasadsanjeewa43102 жыл бұрын
Made by indian ...?
@mikebailey25042 жыл бұрын
Wish Indian made trikes
@wooddawg48683 жыл бұрын
Indian makes a fabulous engine in their touring/bagger line. If they can get away from pushrods their in a new maintenance category.