How tall are you? Going to get these but can’t decide on 12” or 14”. Great vid, thx. Just subscribed!

So do the wires hang out the bottom and then reconnect or down the bottom and through the curve like they are on the Harley factory?

I need some 14" (1.5's) on my 2024 Road Glide CVO asap.

Great guideline to installing bars… watched twice then used video to help when I needed it…bars look great and feel even better.

Installed exactly as the video instructed and now I got ABS and engine lights on. c110463, p151000, and p212700 codes will not clear. My ABS is acting up, no cruise control, and in some kind of low performance mode... wtf happened???

Ill guess all the torque numbers are in paper instructions?

These are 10" or 12"? Great video.

Your video is great straight forward. Your advice worked perfectly. Thank you.

Helo, I got SG 2024. I ordered 12" Bison, do I need clutch extension or oem is long enough? TIA

You said the bike has the 10 inch mayham bars and you are going to install a new product, but I didn’t hear the name of the bars you are installing. I would like to put these bars on my 2013 Street glide, can you tell me the name of these bars and also do you sell the de-pinning tools?

Great and informative video! One suggestion I have is to test all the functions of the controls BEFORE re-mounting the handlebars to the tree, or at least before re-installing the plastics...just in case something is not right.

Life saver. Thank you!!!

What grips are those

Other than the top bend what is the difference between the spearhead and pathfinder bars for the 2024 RG?

Dude! Thank you!!! Just installed bars. Light was on. This fixed it: thank you

This is a great video. I was able to complete the job in about 4 hours going real slow. One problem those is that the the clutch and brake lever mounts have about a 1/8" or 1/16" inch gap. The controls arent moving but there is a gap. Any idea ??

Hello, great video, thank you! For a 2015 Street Glide Special, do you need to extend the electrical wires or clutch cable at all, for a 14" bar?

Can you still use the stock mirrors with these 12" bars, like can you see them? Looks like it. I had 12" bars on a 23 street glide and with that older design you couldn't see the mirrors at all, they were perfectly blocked.

Your video sold me on the KT's Going to put a set of 14" bars exactly like those on my 2024 Road Glide 3. Thank you!

Great video. Thank you for sharing!!!

Great video. I ordered the bars and can't wait to install them.

Any chance on a 08-13 RoadGlide video

This was an absolutely fantastic video. I just watched as I went through it on my own the only issue I have now is that when I start the bike up, I hear a weird clicking noise when the ignition is on, and it won't start. It'll just keep turning over until I give it some throttle, and then when I do it pretty much red lines. Any thoughts? It's killing me

I changed my bars and I still have the triangle light, I unplugged both brake and clutch wires several times and still have it. Any suggestions

Nice video

So you only need a longer clutch cable for 12 inch everything else will work ok ?

Thanks!

Excellent how-to. Thanks! I'm actually putting stock bars back on, but it's the same process.

Where can I find those grips you have on the road glide part#?

Had the triangle come on in the first 100 miles, not showing any codes, cleared the non codes anyways, also unplugged the wires like you said. Still have the triangle. I assume the bike if off when I unplug the wires then cycle back on?

Do you pull the main fuse on this bike before you start the work? if not, did you have any issues when restarting post install (error codes that needed to be cleared etc)? Also I thought that little plastic nub on the throttle side switch assembly is there to go into the channel in the throttle grip to keep it from rotating freely all the way around?

Best "How-to" video I've ever viewed!

Whats the length of upper clutch cable required to run a set of 14” patriot baggers? I bought a set from your website.

Great work on keeping up with the new models. I ride with a veterans group and 70% of the bikes are running KST bars we love them to include a new 24 road glide. Keep up the good work hope to see you in Laconia

I was certain I would be returning my bars for prewired. I watched this last night, slept on it, woke up this morning and did it exactly as he describes (down to the 12 ga stranded) and it worked in an hour. Thank you!

Hi i'd like to put an ape 10" on my street glide 2008 must i buy extension cables ? Thank you for the answer

You’re a life saver!

You can actually adjust the handlebar angle after complete assembly by simply removing USB drawer. It will give you perfect access to adjustment bolts

High Occtane H.D. is putting the patriot bagger 12" on m 2024 CVO StreetGlide having hard time with the brake line telling me need to put 4" extended brake line for a safer & better looking Job. i have been waiting since February

Great video. I have purchased the 12” Bison’s and I’m so looking forward to getting them swapped. Harley says they charge 7 hours labor and wants $900. I am in Indianapolis, any suggestions on somewhere I can get them installed cheaper without voiding warranty?

I have a 2022 Road Glide Limited, it has heated grips is this a separate wire to pull?

Great channel & info.. would you pls tell me where you purchased the custom service covers & bags ? Thank you.

Excellent Video! One thing I would like to add is that the handlebars can be adjusted with the fairing in place by removing the cell phone tray, it just slides out. With the tray removed you have access to the riser bolts.

Dude that is amazing video I am somewhat a mechanic but not on motorcycles I had it the whole thing done handlebars installed everything in 2 hours with your video help you are simply just totally amazing thank you for everything it saved me $850 but Harley was going to charge

Great video. If I want to simply adjust my stock bars, can I simply remove the Road King badge from the nacelle, access the bottom two bolts to loosen, and then retorque? Risk of damage to the badge? Thanks.

Brilliant video, straight to the point, easy to follow, and fixed my issue. Thumbs up from me 👍🏻

Great video bro…

Every time I hold down the odometer, the PIN code comes on. I guess I’m not doing it right. I need to clear a code but I’m not doing it right. I’ve tried with and without the fob

Wow thank you. That was explained excellent.

Thank you