I think Nissans are easy to repair. The hard part is finding accurate information and that struggle is not exclusive to aftermarket, when it comes to Nissan.

Not sure if the parts are interchangeable. Wish i could be of more help. But with a little manipulation, time and fabrication. You can make anything work.

ill see if i can figure out a way to get something definitive on diagnosing that without a BCM communicating scanner. tomorrow when i get to work.

ive got snap on autel launch all bi directional tests but missing thde option to roll the windows down likeit says in the flow chart

@@philh9238 I did not get a chance to do any testing on a Known good vehicle yesterday as we were really swamped with work. But from looking at the wiring diagram i would think that you are looking for some communication on pin 16 (orange) at the passenger window switch when using the master switch to command the passenger front window up or down. If you check that circuit with a scope and you got nothing perform the same check at the master switch pin 14 (orange). Also confirm circuit integrity to the BCM pin 132 (green).. I have never gone to war with one of these power window systems (they don't break very often in that way) so i cant say for certain what type of signal your looking for (possibly LIN). However the good thing is that this system is pretty much the same on all Nissans from 07 on up. So if you have a 07 plus nissan at the shop now it wouldn't take much to pop the switches out the door panels and compare the signals going into the passenger switch from the master switch to see what your looking for. The wire colors will likely be different but the operation is the same based on the wiring diagrams that i looked at. Hope this helps. 🤔

@@Autofixpals for sure man. yea the communication line is fine checked all 3 spots bcm master and passenger switch along with power wire to the switches. so im going to chuck an aftermarket master switch and let you know. switch aftermarket is only 42.00

Isnt that sad... But I think that problem is exclusive to the pathfinders though. I have not changed any fans on a Murano.

What DTC? p0340? Yes Cam sensors were an common failure on earlier VQ engines. Verify the DTC for me.

@@Autofixpals thanks sir, will let you know shortly

@@Autofixpals sorry sir, The code is P0350 IGN Signal Primary Also it has 2.3l engine

@@konquerorx not familiar with the 2.3 liter engine. I dont think that engine is in the US market. Is this a vehicle with a distributor?

@@Autofixpals coil on plug brother. Its here in New Zealand. V6 2.3 2006. Best to scope the cam sensors?

lmao.. I have not heard that one before.

I MIGHT BE WRONG BUT YOU MIGHT BE LOOKING AT A GROUND PROBLEM .

I believe you are correct. I will verify this tomorrow. It may not be on a 07 Altima, But they have not made many changes in their PCMs. Why was the PCM being replaced originally?

@@8power0 its plausible.

the ground for the coils are on the top. one of the two 10mm bolts is the ground for the ign coils, make sure they are clean, also the ground cable under battery i believe is prone to corrosion. Follow the negative cable and make sure all is good. Voltage drop test it.

Thank you Hakim. I apologize it's a 2012. I'd appreciate you checking the trigger wires with just KOEO. If not too much trouble, each back probed and unplugged to see if they have any voltage. Thank you Hakim.

i agree. But it happens at all manufacturers. People at the factory sometimes make mistakes. However the dealer that sold the car was responsible for catching that mistake.

@@Autofixpals hey my friend how are you doing?I have issues with my 2003 Ford econoline 350 van .Oil is leaking out of oil pan Any "easier " fix than removing pan.If there's not then any video or any kind of help how to replace gasket on that pan??As it looks that it's not easy fix because of tight space to drop oil pan.Thanks and I hope to hear from you with good news 😀

@@ebutariq99 wish i had good news. That job is a major Pain in the Ass. no easy fix

@@Autofixpals can I just keep on adding oil or there's some kind of product that I can add to oil to seal it from inside??

@@ebutariq99 never been successful with fixing any leak using a product in a bottle. You certain its the oil pan gasket?