In this episode, we install the GM Led Perimeter bed lights on my 2023 Chevrolet Colorado Z71 GM Part number 84861986 This kit will also work on the 2023 GMC Canyons as well!
Пікірлер: 57
@BikeDr4U18 күн бұрын
Thanks for this! My bed lights were installed by the dealership (the truck was ordered by another customer who decided he didn't want it when it arrived.) Nobody at the dealership showed me how those lights worked. I was actually going to take it in to see why the lights didn't work. There's nowhere in the owners manual that explains how the bed lights work.
@mpfsr11 күн бұрын
Thank you for the video, made it easy to find a good place to power mine up. I used some Amazon ones and an existing bed hole that fit my switch perfectly.. Gonna look for a tailgate type switch to replace the supplied switch, so when I open tailgate it turns on the lights. Just don't wanna forget one day and kill my battery..
@possiblyfakechannel11 ай бұрын
I just installed my set after watching your video, I didn't have to depin or anything to get the harness through that tight spot. If you put the red part of the clip facing up and stick it between the two plastic tube like pieces that hold the plastic rails down it will go in. It takes a little bit of pushing and wiggling but it fits perfect and looks much cleaner :)
@jayadams160211 ай бұрын
Exactly what I did
@HCBossVos10 ай бұрын
Thank you so much for this video!!! I dremmeled out just a little material to run the lights into the access hole that was too small. This was so much better than your option as it hid the wires better.
@JoseDelgado-ho1cf Жыл бұрын
Nice! Thanks!
@johnwhitneykokalis9990 Жыл бұрын
Love your videos.
@jacobvogler5069 Жыл бұрын
In order to get them through the intended port hole, you have to decouple the clip from the top of the pin with a small flathead (careful not to break it off), then remove the red slider piece. Once the red slider has been removed from the clip, you can get it through there and then reassemble on the other side.
@brianfredricks9234 Жыл бұрын
How did you detach the coupler?
@jacobvogler5069 Жыл бұрын
@@brianfredricks9234 you have to pop it off with on the sides where it's clipped over the tabs. Use a small flathead and pop one side, then the other.
@D7dronetech11 ай бұрын
Very helpful, thanks!
@jessegarcia797976310 ай бұрын
Video?
@CharlesBeaven Жыл бұрын
Keep up the good work on the Colorado content.
@jerrystowing1475 Жыл бұрын
Great video!
@imfixitalex Жыл бұрын
Thanks!
@MollyTV18 ай бұрын
Great video Thx !!! 🎉 I have a spray in bed liner thankfully
@dukecorbett4317 Жыл бұрын
Just did the lights on my truck. I ended up de-pinning the moles connector and reconnecting. Clean easy install.
@brianfredricks9234 Жыл бұрын
How did you depin it?
@dukecorbett4317 Жыл бұрын
@@brianfredricks9234 if you Google De pin molex there are tons of videos. It took me forever to figure it out but once I did one wire it was very easy for the other 5. Make sure you take a picture so you rewire in the correct order. Lesson learned the hard way. Harbor freight sells de pinner or you can use a thin paper clip. The clip you have to lift to pull the wire has to lift just a hair and the wire comes right out. Takes some patience getting the first one. However worth it. The finished product is much cleaner running the wire properly.
@alp2169 Жыл бұрын
Thanks for the video! Very informative. I imagine using that side grommet hole to route the wiring won't look very nice if you have a spray-in bedliner. If the wires don't release easily from the clip I would almost be inclined to cut the wire, run down through the intended hole, then splice back up with waterproof wire nuts/connectors, tape up real good and tie wrap to the harness underneath.
@mt186 Жыл бұрын
I'm guessing it's pretty easy to depin the connector. You could also use a step bit and drill a hole big enough and just add a grommet
@rayyoung2785 Жыл бұрын
I hope you will add a 12v outlet next to the USB ports in front of the shifter. Great video.
@ronaldfox801610 ай бұрын
You can can plug in hole I did it its easy put red part of clip on top and push hard
@616fun Жыл бұрын
Can you release the wires from the connector then then reinstall the connector from underneaths once you pass it through the bed sidewall? Typically those connectors are pretty easy to release the wires. I ordered this kit and will try to do this on my install.
@LoneWanderer479 Жыл бұрын
There are instructions for this if you have access to the GM service information page. Not sure who gets access to that. But they have an entire accessories installation section
@BadlandIndustries Жыл бұрын
You may be able to de-pin the connector and send the wires and loom over the bed corner where you thought it should go. Re-attach the wires and plug it in.
@brianfredricks9234 Жыл бұрын
How did you de pin it?
@jamesbondero61704 ай бұрын
Is this kit backward compatible with the second gen Colorado? I have a 2020 and would like to have lights that turn on by touching the lights like these do.
@jasonellert775211 ай бұрын
Great video........I want to install the power outlet in the bed, mine didnt come with it. But cant seem to find the gm part number or kit.
@stephenbaldwin56749 ай бұрын
Will these bed lights come on when you open the doors automatically or do you have to get out and manually touch them?
@vt0wndub Жыл бұрын
Good vid! Do u have a link where u purchased? Thx!
@JPickettIII5 ай бұрын
Can you control the lights via the infotainment screen?
@rogerwilliams949510 ай бұрын
I am attempting to install bed lights in my 2023 Colorado Z71 with a switch, utilizing the plug that you are using. Although I am using the oem pigtail to connect the rocker switch. I tested and had power to the switch and after soldering my connections, no power. Do you know the fuse location? Thank You, You do an excellent job with your videos.
@OrangeRuk11 Жыл бұрын
The bed lights look good! I wonder if the Trail Boss can be fitted with the factory 120v outlet in the bed 🤔.. Like, if it’s pre-wired for it behind the blank cover lol.
@David-cr6fb11 ай бұрын
I mean I doubt they have the 400W inverter behind there
@terryjones836021 күн бұрын
Do these shut off after a while, or will they run down the battery if you forget to turn them off?
@garysmith2261 Жыл бұрын
Will this lighting system work for a 2022 Canyon?
@remingtonrunyans9099 ай бұрын
Can you control the light from inside the cab ?
@darthwhat575 ай бұрын
Anyone know if these will work and be plug/play on older colorados? 2021
@kerwinfantauzzi64479 ай бұрын
In order to get the plug down without cutting your grommet you will need to disconnect the plug and it will slide in. Your video was very informative but you can unplug the connector to slide down the correct area
@glivings1689 ай бұрын
May you please show us to do a tail gate LED light strip for the 2023 Colorado/Canyon?
@randymancini4832 Жыл бұрын
You just need to Dremel out about 1/16” of an inch and they will fit down where they should
@Tacito13 Жыл бұрын
Can you install some Ditch lights next?? Would be awesome.
@mariagiordano3902 Жыл бұрын
didnt know they has the drop in bed liners i thought they were all spray in. is that a 23 or a 14
@alexgerst Жыл бұрын
2023
@AllOutNoobHater Жыл бұрын
Instead of having a plastic bedliner, just get some paintable bedliner and do it yourself. Super easy to do and feels the same as a spray-in.
@jimmycline477810 ай бұрын
Or pay 450 and get it done right with a lifetime warranty!
@AllOutNoobHater10 ай бұрын
@@jimmycline4778 either paint it on yourself or get it factory
@808_rip_um_keaulana Жыл бұрын
🤙
@core4X Жыл бұрын
Does the bed have to ne open ror tnem to turn on? I'm pressing mine and they don't turn on
@imfixitalex Жыл бұрын
not sure I wouldn't think so. you do have to touch the light for 2 sec before it turns on.
@core4X Жыл бұрын
@@imfixitalex oh ok. Thanks for the response! Great vid!
@jimmycline477810 ай бұрын
You gotta get rid of that plastic bed liner, it will rust your bed in a few years,,, I payed 450 at dealer and got a lifetime warranty on my sprayed in liner,,it will look so much cleaner without everything sliding around too!
@mikesmith2383 Жыл бұрын
If you have a drop in bed liner, the best thing you can do is remove it. Absolute worst thing you can do to a pickup bed.
@honeyberry4009 Жыл бұрын
Should have cut the wire beore the clip, ran the wire through the hole you cant see it in, then re attached the the clip