2024 Enfield Meteor 650 Belt Drive: Everything You Need To Know

Рет қаралды 3,678

Ай бұрын

A guide on how to align and tension the RSTech belt drive kit on the Royal Enfieid Super Meteor 650.
If you found that this video helped you, please show your support and buy me a coffee:
buymeacoffee.com/teachertthai...
Belt Drive fitting video: • Royal Enfield Meteor 6...
Belt Drive kit available from - RSTech - rstech.my-online.store/produc...
Interceptor Belt Drive Review. 10,000Km : • Why Royal Enfield's ne...
/ teacher.t.thailand

Пікірлер: 58

@rened2144 14 күн бұрын

Belt drive is installed, was not to difficult after looking a view times your vid. Thanks again. very helpful. Tomorrow a testride and after i will check te tension again.

@Teacher-T-Thailand 14 күн бұрын

Great stuff. All the best. Enjoy the smoothness and cleanliness 🙏

@shawna7078 Ай бұрын

Installed my belt drive on the weekend - I work alone and its straightforward enough. I didn't remove the exhausts but did unbolt the shocks. It is possible to remove and refit the rear wheel just on the center stand but a bike lifter would be a good investment. Pretty easy to remove and refit the swingarm. Refitting the wheel on the other hand - arrghh. I would recommend a rattle gun for anyone working alone. I couldn't get the front sprocket bolt to budge with a 600mm long breaker bar. Impact gun - 10seconds and safer. Working alone getting the tension right was a challenge. I set the tension at 21mm with the bike on the center stand with the rear wheel off the ground shocks installed (based off the other installation video). Then with the shocks off you can the lift and chock the rear wheel to simulate the loaded bike - if you aim for a pretension of 25% loaded then the shock will compress approx. 15mm (YSS shocks) when you are sitting on the bike. So I simply raised the swingarm 15mm from its static unloaded position and checked the tension again. The bike is noticeably smoother to ride. I have found I need to shift down a little earlier than with the chain due to the higher gearing. But otherwise its great

@robertstraghan9009 Ай бұрын

While I applaud your ingenuity, however using 21mm unloaded as a base measurement will not yield the correct result. I really recommend that you verify proper tension as Teacher T shows, as proper belt alignment and tension is important for system life. You must have the higher gearing option - Teacher T has this as well

@shawna7078 Ай бұрын

@@robertstraghan9009 On my list to do 👍Yes I have the higher gearing option. Its perfect and I don't miss any lack of acceleration.

@Teacher-T-Thailand Ай бұрын

Great effort. To do this on your own I must applaud. Hopefully soon you will notice the improved fuel economy also from the higher geared pulleys. I was 26kpl, now achieving 28 kpl but still checking over time 🙏

@user-hk9tx1wu6m 21 күн бұрын

RE should give it as a standard fitment in it's top variant of Super Meteor 650

@Teacher-T-Thailand 21 күн бұрын

They should certainly offer it as an optional extra, like they do handle bars and seats. 🙏

@paulmurray5525 Ай бұрын

The back pulley was wobbling 😮

@Teacher-T-Thailand Ай бұрын

Not torqued until completion. The rear hub sits on the rubber cushions only until torqued then the pulley will align with the bearings 🙏

@specialized29er86 18 күн бұрын

I'm really surprised how well priced the kit is. Wondering what's the benefit of changing the front sprocket to the 38 tooth.

@Teacher-T-Thailand 18 күн бұрын

Ahhhh. Not the front sprocket, but the rear one. It lowers the engine revs at top speed, and has pushed my kpl from 26 to 28kpl 🙏

@TyphoonPilot1 Ай бұрын

Nice. TT.

@Teacher-T-Thailand Ай бұрын

Thank you 🙏

@lnk4328 Ай бұрын

Excellent presentation. Cleaver use of the center stand to hold the tensioning tool. How many miles did you have on your chain? Think that when I do this conversion, I will go ahead and remove the swingarm. No better time to inspect and grease the bearings.

@Teacher-T-Thailand Ай бұрын

Thank you. Only 7,000 km on the chain. About 4,300 miles. I hear UK riders are changing them at 7,000 miles. The Sing arm is very easy to remove and replace, compared to the rear wheel. Good luck with it all 🙏

@johnalleman1134 Ай бұрын

Very happy with my Interceptor belt drive kit. Smooth, quiet, clean and low maintenance- what could be better? 😅

@Teacher-T-Thailand Ай бұрын

Good to hear. I agree. Low maintenance and easy cleaning is a winner 🙏

@ThePlough1978 Ай бұрын

🤨 A chain and sprockets 🥳 *Crap Game* 🎉

@Sha-yw6fb Ай бұрын

❤ keep up the good work mate..

@markkiger927 Ай бұрын

Having adjusted Harley and Indian belts for years, it’s much easier to set the tension with the rear wheel off the ground and no rider on bike. So, if you raise your bike’s rear wheel off the ground, apply 10 lbs of force with the gauge, what amount of deflection is shown? If you’ll post that number, it would allow others to set their belt tension without having to have a second person sitting on the bike.

@Teacher-T-Thailand Ай бұрын

It’s easier sure, but it doesn’t take into account people’s different preload settings on their suspension, after market suspension, or their weight. So the first time it must be done on the ground with the rider or someone of similar weight to the rider sat on the ground. Once set correct,y, then yes I suppose you can get a second reading on the centre stand and remember it, but that is an unknown figure for different individuals. 🙏

@robertstraghan9009 Ай бұрын

My HD manual specifies checking the belt on the side stand, at ambient temperature. Others choose to tension the belt with Rider, as being more appropriate to check tension in loaded condition. Either way works, as long as the Gates formula is applied. Earlier RSTech instructions gave both calculations, but it was creating more confusion that helping and more than one Rider had the belt too lose.

@robertmoon6492 Ай бұрын

Hi Trevor, I've ordered a belt kit, from RS Tech, for my Super Méteor, it should arrive in France in the next couple of weeks. The spoilsports at my RE dealer said 'officially' that fitting it would invalidate the warranty, but 'unofficially' they are really looking forward to fitting it, and seeing how I get on with it. I look forward to seeing your rideout review. Merci 😊

@Teacher-T-Thailand Ай бұрын

I’ve had mine on and off 4 times. Easy to revert back to chain for warranty issues. Good luck with it all. Leave feedback when done please. All the best. Teacher T 🙏

@ThePlough1978 Ай бұрын

Darn, the virus 🦠 is spreading. *Crap Game* 🎉

@Teacher-T-Thailand Ай бұрын

@@ThePlough1978 to become immune, you need to be infected.

@nasirdiler7677 25 күн бұрын

Meteor 350 belt drive kit price

@robertmoon6492 25 күн бұрын

@@nasirdiler7677 Hi I don't think the Meteor 350 kit is or will be available in the near future.

@7Archie4 27 күн бұрын

Could you please advise if there is a slot available in the middle of the bike for mounting a footpeg, given that it is a forward control?

@Teacher-T-Thailand 27 күн бұрын

Yes there is. Easy enough to put a mid peg, but not easy to move the gearing or braking controls. A popular mod with some when riding on open roads. Just move your feet to forward pegs when needed. Not advisable for safety, but possible 🙏

@rened2144 20 күн бұрын

perhaps is there anybody how tase installed a rev counter instead of the tripper (what i don't need) so please your advice. by the way next week i going to install the belt drive 👍

@Teacher-T-Thailand 20 күн бұрын

All the best with the belt drive. I plan to make a new tripper video soon. It’s been updated and much better. Rev counter would be useful. I will look into it 🙏

@uweyaa Ай бұрын

👍👍👍 Hast du keinen oberen und unteren Beltschutz,damit keine kleinen Steine auf den Belt fallen?

@Teacher-T-Thailand Ай бұрын

No. If you want to add yourself you can. Covers also trap stones in the system.

@uweyaa Ай бұрын

@@Teacher-T-Thailand An meiner HD HERITAGE habe ich den Schutz dran. Habe schon einige HDs gesehen wo kleine Steine zwischen Belt und Pully beides zerstört haben.

@robertstraghan9009 Ай бұрын

@@uweyaa This is not for off-road applications, so one needs to question the purpose of the guard - In the case of a chain, is it to keep the chain from flinging oil all over you and the bike? Or in the case of a belt/chain, to keep your fingers out of the rotating chain or belt? If the reason for a guard, is to keep out rocks, is not an L shaped guard more of a rock trap than a shield? Unless the guard is fully enclosed (impossible with an endless belt unless a 2 piece guard) a rock can get trapped in the guard, increasing any potential risk; and why I removed my guard; thinking that any rock will get flung out. So is the guard to keep out rocks, or a mandated safety regulation to keep out fingers and bits of clothing? Yes s**t happens, but 160,000 km on the last Harley belt, while living at the end of a 1 km long gravel drive, and pretty sure I might have gone through some roadworks. I and the other Riders that have covered millions of km, cannot be simply that lucky, and the belt drive has stood the test of time

@simonshylla9739 Ай бұрын

Teacher T, what is the length of the rear shock absorbers of the meteor 350? and can they be used on the super meteor?

@Teacher-T-Thailand Ай бұрын

The standard Meteor 350 rear shock length is 320mm, where the Standard on the Meteor 650 is 310mm. The 350 original shocks have a bad reputation also. I doubt they would be strong enough to support the extra weight of the Meteor 650.

@simonshylla9739 Ай бұрын

@@Teacher-T-Thailand thank you for your reply. I guess I'll have to find other options to reduce the height of my super meteor. The hagon shock absorbers are somewhat expensive to order to India. Thanks Teacher T.

@Teacher-T-Thailand Ай бұрын

@@simonshylla9739 Sorry to hear that, I know you can get Honda wave after market shocks here in Thailand. Very cheap and an option to buy them at 290mm. I’m tempered to buy a set myself and compare them against the Hagons Fittings look the same. 🙏

@simonshylla9739 Ай бұрын

@@Teacher-T-Thailand Thanks for your reply again Teacher T, there is an option to use the Bajaj Avenger shocks as well but some of the mechanics that I enquired said that they might not be able to support the weight of the super meteor even though the Bajaj Avenger is a little heavier than the Honda wave.