Yaesu really dropped the ball here. Customers would be MUCH happier with the HDMI jack and none of this drama. It is was a mistake for them. Great video. Thank you.
@arekx2 ай бұрын
HDMI also provides voltage. If Yaesu implemented dvi badly then they could do bad hdmi implementation, too.
@timd18339 ай бұрын
In my younger days as an ET, I was checking a tiny resistor like that and when I checked it with a meter, it read OK. Chased my tail for a while, everything pointed to that resistor being open, yet it read OK. Then, I connected my meter leads to adjacent components connected to that resistor (11:45) and it read open! The pushing together of the meter leads on the resistor was enough to push the cracked resistor together and allowed it to read OK. I learned a valuable lesson that day.
@blackknight13979 ай бұрын
God’s Blessings on that fix! That’s going to make a lot of FT-10DX users happy ❤
@OleF1129 ай бұрын
Nice work, Peter. I guess, Yaesu´s choice for DVI was the licence fee for HDMI. There is no other good reason in my opinion. Saving 1.5 USD each TRX is more important than satisfied customers...the bean counters took over ;-) Thank you for a nice vid - again. Genieß den Herbst, ideal für viele schöne Videos, Peter. Bleib gesund und 73 de Olaf.
@TRXLab9 ай бұрын
Hi Olaf, don't exactly know what license fees for HDMI cost but however it is always about money for sure....Alle Gute für dich und bleib gesund.
@Larry-AK0Z6 ай бұрын
@@TRXLab US$0.15 for each end-user licensed product. US$0.05 - If the HDMI logo is used on the product and promotional material, the per-unit fee drops from US$0.15 to US$0.05. Use of HDMI logo requires compliance testing.
@johncundiss90989 ай бұрын
I did not know that an adapter could do that. I did not know there was a 5 volt line going through the DVI ether. Good to know. Thank you for the peek inside as well.
@Yannis..9 ай бұрын
Thank you very much Peter, I will definitely buy a DVI monitor for my brand new FTDX-10 radio !!!
@G3PWP3 ай бұрын
Thank you for a superb video production Peter
@syfr7 ай бұрын
Very nice job! Well done and well documented, many thanks
@chevyguy11288 ай бұрын
Another nice repair video excellent soldering skills especially dealing with surface mount components.
@chickennugget33629 ай бұрын
Thanks for this mate. My weekend TRX lab fix!
@sporsterini2 ай бұрын
Thank you for sharing your technical experience with the Yaesu FTDX-10 external video display issues. I was going to purchase this model until I heard about the external video issues. Now I feel more confident about ordering one. I really need to learn how to solder SMT components. I have a SMT repair station.
@montygore12009 ай бұрын
Thank you Peter. I have not seen this radio yet.
@wolfhawg9 ай бұрын
Thanks Peter. Great job. 73s
@UnhingedHarry4 ай бұрын
Great video, thanks.
@maxwalker46599 ай бұрын
Peter, thanks for your reply. Because pin 14 had 5v I assumed the chip would not be faulty and that's why I asked for your advice. Thanks again for your time.
@davidbrowne15886 ай бұрын
Hi The 5V is put to pin 14 of the dvi socket after the dvi/hdmi chip , so the chip can be bad, it is that this one is lucky the fuse did its job, i have 5v on pin 14 but no output on the dvi socket, Dave
@davidbrowne15886 ай бұрын
Hi Did you Fix your radio, and was it the chip, Thanks Dave
@maxwalker46596 ай бұрын
@@davidbrowne1588 Hi, no I haven't done anything as I have to send my radio 1 thousand klms for repair. I will just live with it as it's too risky to post in the mail. I thought using the correct DVI cable would eliminate this problem, not so.
@davidbrowne15886 ай бұрын
@@maxwalker4659 Hi max, were are you, I have just ordered 10 chips, they are very cheap, Dave UK
@lenny0272Ай бұрын
OMG so cool. Thank you
@JxH8 ай бұрын
I really wish that Yaesu would "JUST" sell an 'Approved' DVI-to-HDMI adapter. Or at least "JUST" publish a white paper on exactly what to do, perhaps making sure that the adapter has such-and-such characteristics. It's all madness. Edited to add "JUST" in 2 places. Somehow the word "JUST" makes it all okay.
@JohnFT34144 ай бұрын
Just buy a monitor with both hdmi and dvi Jack's. 24 inch ASUS worked for me.😊
@tomdonahoe35393 ай бұрын
Thanks for this valuable information. 73s 😊
@DennyInDurham9 ай бұрын
Thanks for confirming what many of us thought. My only quibble is, it isn't a bad DVI-HDMI "adapter" problem (it's not an adapter, it's a pin mapping documented in the HDMI spec), it's Yaesu's design, specifically that fuse value. Since the spec calls for both hot-pluggability and for the source (the FTDX10) to actually power some monitor circuitry when the monitor isn't on, that fuse needs to take that into consideration.
@TRXLab9 ай бұрын
Well, yes and no... There are obviously DVI/ HDMI adapters on the market which simply are consuming more current than others. If you have such a" high consumer" that is bad...
@DennyInDurham9 ай бұрын
The "adapter" doesn't consume any power at all... they are (by spec) just straight-through cables no more active than a DVI-DVI cable... the actual device (DVI or HDMI) may consume within a permitted limit of steady-state current, which is different when the device is off (or not plugged in) or on. The hot-plug requirement means the fuse must survive brief inrush current (be slo-blow). The FTDX10 design obviously didn't take this into account.
@hancecrawford9 ай бұрын
Hi peter thanks once again for another video the owner was lucky it was only that tiny fuse and not the chip electronic have got smaller in size must be hard for you to see such tiny things hard for the eye to see them.
@TRXLab9 ай бұрын
yes, without microscope it is impossible to those repairs..
@jamesseaman29509 ай бұрын
The +5 volt on pin-14 is there to keep the monitor awake. If it disappears, any display thinks the DVI source is turned off which puts the display into sleep mode.
@bairamzubi2807 ай бұрын
so can i short it? today my monitor won't go on :(
@hankhardisty943321 күн бұрын
Thank you!
@notfallmed9 ай бұрын
tnx vy 73 👍
@DonDegidio9 ай бұрын
Hi Peter, I had heard that there are only a few HDMI - DVI adapters that will work with the FTdx10. Glad I still have a DVI monitor available. Stay safe. 73 WJ3U
@TRXLab9 ай бұрын
Yeah, we have not look into it yet, but some DVI/HDMI adapters seems to draw more current than others. That would explain it..
@bblod48969 ай бұрын
I know it's Saturday when Peter posts a video; thanks.
@ouijim9 ай бұрын
Popular radio. I own Yaesu FTDX10. I've read about problems with external display connection. Seems this may be common problem and solution. Thank You.
@13EL1219 ай бұрын
Wie immer ein top Video, Peter. 👍Schön dass du dich an den FTDX10 ran traust, den Fehler und die Lösung präsentierst. Habe selber einen FTDX10 der eine Reparatur benötigt. Das Gerät hat eine miserabele SSB Modulation. Leider ist die Garantie bereits erloschen, da es ein Erbstück ist. Leider scheint sich keiner an das Gerät ran zu trauen. Alle meine Anfragen blieben unbeantwortet. Vy 73 Ralf
@TRXLab9 ай бұрын
Hallo Ralf, schau mal welche Firmware auf dem Gerät ist. Sollte es die erste sein (1.0), kann das der Grund sein. In diesem Fall Total Reset und dann die neue Firmware drauf. zu 25% aller Fälle ist es damit erledigt...
@13EL1219 ай бұрын
@@TRXLab Hallo Peter, vielen Dank für deine Antwort. Firmware ist die neueste verfügbare. Ich werde das Gerät demnächst mal an anderer Stelle testen mit anderem Netzteil und anderer Umgebung. Das Problem tritt auch am Dummy auf, unabhängig von Mikrofon oder Sendeleistung. Vielleicht sind es ja tatsächlich äußerliche Einflüsse?🙈 Ansonsten muss ich mir eine sinnvolle "Verwertung" einfallen lassen. 😉 Schönen Sonntag und Vy 73, Ralf
@TRXLab9 ай бұрын
wenn die neuste Firmware drauf ist, sonst keine äußeren Einflüsse zu finden sind, wird es eng. Es gibt dann im Prinzip nur noch 2 Fehlerquellen. 1. Ref Ozil. 250 MHZ an TP1097 Main Board. Da reichen schon mehr als 30 Hz Toleranz, um das auf SSB zu hören. Je größer das Delta, desto schlechter SSB. 2. Da es keine SSB Komponenten im analogen Teil des Gerätes gibt, wäre das dann ein Fehler des SDR FPGA. Das wiederum glaube ich nicht an erster Stelle, da ja alle anderen Modulationsarten funktionieren....
@13EL1219 ай бұрын
@@TRXLab danke für die Hinweise lieber Peter. Der 250er ref. Oszi scheint leider nicht das Problem zu sein. Die SSB Modulation klingt eher wie "FM'ing". Ruheströme der Endstufen oder einer der (Vortreiber/Treiber) bzw Endstufentransistoren könnte ich mir vorstellen. Leider will sich niemand der Sache annehmen. Ich habe auch keine Hinweise von den Hinterbliebenen erhalten wo dass Gerät erworben wurde. Im Endeffekt wird es wohl leider ein teurer Türstopper. 😔 Wünsche dir einen schönen Sonntag und freue mich auf baldige neue Videos von dir. 73, Ralf DO7RU
@SMShannon555 ай бұрын
Instead of replacing the fuse with another fuse, could it be replaced with a resettable “fuse” or circuit breaker?
@tomkissinger839 ай бұрын
What is the part number for this fuse?
@bairamzubi2807 ай бұрын
Thanksfor that, i tryed open myft 710, but i guess this fuse is on the otherside......any advice? What do u think if a give 5volts on pin14 on the cable from an external source???the monitor should work, shoundn't it?
@Homer195219 ай бұрын
D1800 Ifsm for RB521SM-30 is only 1A. My understanding is Yaesu on the FT-710 has upped the Fuse to 1A for that port. I suspect they must have upped the rating for the diode too.
@yllib685 ай бұрын
Great video Peter!! Hey, could you tell us what that tool was that you actually pulled the fuse with and also what flux you used please?? Thanks.
@iw0hex9 ай бұрын
Thanks for sharing this interesting video Peter, as usually nice job. 73s de IW0HEX Pasquale.
@TRXLab9 ай бұрын
Thanks my friend! Take care 73
@charliem.99989 ай бұрын
I love these videos of Peter and Olaf ... 73s de DL6RDE / AA1KD, Charlie
@davidautry48578 ай бұрын
Great video as always! What brand/type flux do you use?
@TRXLab8 ай бұрын
Amtech Tacky flux
@lorinhollander40578 ай бұрын
Hi Peter. Wonderful Video. What DVI-D to HDMI adapter, exactly, would be safe to use, are there any? I was informed by a very helpful Yaesu Support Technician that the CABLEDECONN Multi-Port HDMI To HDMI/DVI/VGA Adaptor was the best one to use (I was sent an Amazon link). I tried using that adapter with the Yaesu recommended DVI-D to DVI -D cable connected between the FTdx10 and the adapter and a good quality HDMI cable running from the adapter to a Dell U2415 HDMI monitor without any success, no signal apparently available at the monitor. Either the FTdx10 DVI-D Port, or the CableDeConn adapter itself appear to be nonfunctional, or - even worse - the trial of the adapter itself resulted with the FTdx10 dreaded blown fuse scenario, and I am not sure how to test out the port other than by connecting a DVI-D monitor. Any ideas for the best next step? I have notified the tech at Yaesu, but so far it is too soon for a reply. Thank you all. W6EO
@stargazer76448 ай бұрын
DVI-D to HDMI adapters don't have any electronics in them and don't draw any power - the two standards are signal compatible. It just requires an adapter to route the wires between the connectors.
@wellseewho2 ай бұрын
Can't we just feed +5v to pin 14 of the DVI port and cut the trace to the fuse if it's not already blown? Isn't that the same effect? Isolating the chip from being damaged while supplying +5v to the display and keep it awake. That seems to me is a rather simple soldering job if you have a steady hand and a magnifying glass. Or replacing the fuse with a, say 20 or 50 ohm, resister?
@leslieknowles54557 ай бұрын
What is the rating and spec of the fuse Pete ? thanks
@TheDefpom9 ай бұрын
You can get DVI to VGA adaptors, might e worth picking up a couple
@bblod48969 ай бұрын
At least two of everything 😂
@TRXLab9 ай бұрын
Yeah, I know that Scott, but the power consumption of some adapters are literally to height and that makes the issues..
@fspidersuk9 күн бұрын
My ftdx10 developed a dead touch screen (mouse and dvi monitor fine) after being connected to dvi monitor for a few days. Yaesu replacing screen display and say it could be a floating earth between monitor and radio issue. I struggle to see this as monitor/PC/radio/antenna/dvi-dvi cable are all grounded. Perfect continuity between all. It's an old Dell dvi/vga monitor and the cable is dvi-dvi. At £400 a go for repair i can't afford it to happen again. My question is... Is there a certain method to using monitor/radio? As in switch monitor on last/first or disconnect/connect monitor via radio before switching on monitor. Is there a sequence that safely works? Regards.
@davidbrowne15886 ай бұрын
Hi Peter, I have just got myself a FTDX-10 and yes when i tested it there was no video from the DVI-D Port so i hopped it would be the same as this one, but no, the 5v on pin 14 is good, i all so tested all of the resisters around the dvi chip and all ok, also there is 3.3v to the chip, so it looks like it is the chip, when i was testing with a scope at the dvi port i did see some signals , they did not look clean then i looked at the frequency and yes it was only the 50hz mains interference, have you found meany of these radios with a blown dvi chip, Thanks Dave 2E0DMB
@TRXLab6 ай бұрын
not many but very very few have a blown HDMI chip
@davidbrowne15886 ай бұрын
Ok thanks Peter, I have ordered a ep592 so when it arrives I will change it Thanks Dave 2E0DMB
@rbc12254 ай бұрын
Awesome video. You mentioned people could end up using the wrong DVI to HDMI adapter and to be careful. Can you post or point us in the right direction to the known good converter so we do not make that mistake? Thanks
@TRXLab4 ай бұрын
don't buy cheap crap, just buy a quality A brand..
@maxwalker46599 ай бұрын
Hi Peter, I have the same issue but I have 5v on pin 14. I have continuity tested the DVI-D cable and only have continuity on pins 1-2,7-10,14-18,22-23. I don't want to send my radio 1 thousand kilometers to be looked at if its not a blown fuse. Any advice would be appreciated. Love all your videos. Thanks for all your advice.
@TRXLab9 ай бұрын
Well, as we stated in the video if it is not the fuse it is very likely that it is the chip itself...
@davidbrowne15886 ай бұрын
Hi did you fix your radio,Was it the dvi/hdmi chip thanks Dave
@TKomoski9 ай бұрын
What would you charge for a repair like this Peter *?* *Cheers* *73*
@ukrainehamradio9 ай бұрын
It was very wise decision to use DVI instead HDMI
@TRXLab9 ай бұрын
Thanks for comment. Can you justify the view, maybe there is something I don't see?
@ukrainehamradio9 ай бұрын
@@TRXLab I am sorry! It was sarcasm. I have seen such damage before, including a burnt out chips. People are forced to use crappy DVI-HDMI adapters; DVI does not allow re-connection without turning off the transceiver and monitor. This causes damage. All this could have been avoided if HDMI had been used instead of DVI.
@TRXLab9 ай бұрын
never mind, fully agree.
@stargazer76448 ай бұрын
@@ukrainehamradioDVI is hot pluggable according to the standard.
@user-xv8yr2uv8l8 ай бұрын
you must run a dvi-d monitor with that radio or you will have that problum
@PawelSamoHa9 ай бұрын
Have you noticed you made a nasty solder flake with your probe on the diode pin (last test presented). I hope it will not fall off. Or short to the groundplane. Yaesu learned and FT-710 has a better solution - resettable polymer fuse.
@Ms_Dana10 күн бұрын
Good job, I am looking to buy one of these myself . Questions , do you think a problem with a external monitor or cable blew the fuse , such as a short to ground ? Also could you check the output side of the fuse for a hard ground before replacement . Just some of my thought as a diagnostic tech , more then likely , something blew that fuse.
@TRXLab5 күн бұрын
Yes most time it happens due to bad monitor cable or a bad monitor itself, both can create a short to ground which will then blow the fuse...Hope to see some videos in the future on your channel..
@TheEmbeddedHobbyist9 ай бұрын
Have you thought of getting a pair of de-soldering tweezers they make the problem of removing SMD R's, C's etc real easy and without the mess of flux.
@mikesradiorepair9 ай бұрын
If you watch the video you would see he used a pair of desoldering tweezers to remove it.
@TheEmbeddedHobbyist9 ай бұрын
@@mikesradiorepair to me it looked like two soldering irons. just went back and your correct. it was such an quick off i just saw the meter probes looked away and it was off. I sit corrected. 🙂
@TRXLab9 ай бұрын
@mikesradiorepair Good to see you mate! Hope you are doing well. Take care
@stargazer76448 ай бұрын
Not sure what you think he used to remove the fuse.
@TheEmbeddedHobbyist8 ай бұрын
@@stargazer7644 hard to say under all that flux!
@brucekempf4648Ай бұрын
Is there an adapter sold on Amazon that you can recommend that will be 100% safe to use?
@c64new8 ай бұрын
This fuse is SMD (size 0402?) and has a value of 0.63A, can you tell where this component is purchased? Thank you
@TRXLab8 ай бұрын
directly from ICOM Europe
@c64new8 ай бұрын
@@TRXLab It's funny that Icom sells a component that is for Yaesu rtx ;-)
@maxwalker46596 ай бұрын
Hi David, I am in Australia. What are you doing to fix the display fault. I would like to fix it myself if possible. Thanks for your info.
@TRXLab6 ай бұрын
I'm not David and I don't know what you mean with THE DISPLAY fault?
@maxwalker46596 ай бұрын
@@TRXLab Sorry my mistake as usual. The (Display Port Issue) is what I mean by (Display Fault). I thought this was self explanatory. 73ss Good Luck.
@jasonwatkins39723 ай бұрын
i got a blury green screen on my external monitor even yaesu dont know what it is can anybody advise me please
@WHNorthcote9 ай бұрын
If you are that good at replacing a tiny fuse like that then you could fix my original Yaesu FT-817. It has a problem that even Yaesu could not fix. In fact they did not even know if it was a problem as they checked their report logs and did not find anything resembling it. Another ham said it could be a few SMD resistors that have given out as the main screen characters fade even though the back light is on. They sent it back unfixed even though everything works except the display fades leaving a blue screen that it was already set to. Fancy a poke about to see if it can be fixed?
@jasonwatkins39723 ай бұрын
yaesu said it be about £300 to repair my ftdx10
@LawpickingLocksmith9 ай бұрын
Immer diese Sicherungen!
@mikemcdonald51476 ай бұрын
if they had the hdmi chip in the radio why the heck didn't they give us. an hdmi connector. so much easier
@TRXLab6 ай бұрын
It costs license fees...
@robertvarner95196 ай бұрын
This is why I don't buy Yaesu crap anymore. Everything on my FT-897d went bad soon after I bought it years ago.