Here is an overview on how I installed a 2nd gen Dodge radiator and intercooler in my square body Chevy truck
Пікірлер: 27
@seanjordan44853 жыл бұрын
I'm trying to do the trans crossmember and driveline angle and engine level. Could you give me advice on this. I have a 47re long bed 4 door
@michaelwilson75962 жыл бұрын
Have you had any over heating issue’s with the fan’s being on the back side of the radiator and Innercooler as far as sitting idling or rolling down the highway?
@RicosGarage2 жыл бұрын
No issues at all. Never has come close to getting hot. Towing has been no problem
@CrazylilZoe6 ай бұрын
question? I bought my truck with the core support you have on in this video (grill headlights, etc). I want to go back to the 1986 grill and headlights, all I would need is the core support for that year (86) and necessary headlights and grill?
@RicosGarage6 ай бұрын
Yes that is correct
@CrazylilZoe6 ай бұрын
thank you, great info on this video also
@JohnMontero-Nevaden3 жыл бұрын
Do You Have Enough Room To Put A Chevron Delo Cardboard Oil Case Box Between The Inter-Cooler And The Radiator - If Not I Hope You Live In Florida And Do Not Need A Heater - 1st. Gen Dodges Had A Group Of Engineers And A Truck Driver Working Together Designing The 1st.Gen 5.9 Cummings Trucks - 89-93 - The Truck Driver Told Them 1 Of The Most Important Things Was To Design Into The Truck Was A Spot For A Cardboard Box To Slip Between The Inter-Cooler And The Radiator And To Be Able To Totally Or Partially Block The Radiator As The Temperature And Conditions Necessitated - I Have A 93 W-250 5.9 And The Cardboard Stays In For 3-4 Or More Months Every Winter- My Son & I Put A 93 5.9 - Getrag - 205 Transfer-Case Into A 1985 K30 Crew-Cab - We Massaged The Fire-Wall Back Only 1&1/2"-2" - Only Had To Deal With An Area Approximately 8" High By 8" Wide On The Fire-Wall (A Few Hours!) - Also Added 3/8" Foam Sound Deading To Firewall On Inside & To The Floor - The Stock Heater Air Conditioner All Fit Back Inside Without Any Modifications - We Used The 93 Dodge Radiator - Inter-Cooler - Fan - Dodge Alternator With Added External Regulator - 4" Diamond Eye Exhaust Without Muffler Turbo To Rear Bumper, Very Quiet But Sounds Good - Original Air Cleaner Box & Even The Original Fan Shroud Which Fit Perfectly - The Inter-Cooler Is In The Front Of The Radiator Core Support - The Grill Worked Perfectly - We Made Room For Cardboard To Slip In Between The Core Support And Radiator With A couple Of 3/16" Rods To Protect The Fins On The Radiator - My Son Appreciated The Need For That Cardboard The Last 2 Winters When It Was Cold And He Actually Had Heat, (Northern Nevada) - We Ended Up With 2" Between The Fan And The Radiator Almost Exactly What The Dodge W-250 Had - He Could Hit A Deer At 30 mph And Drive Home - Oh Yes We Did Do A 2" Body Lift & Had Johns Spring Shop In Reno Re-Arch The Front Springs & Add A Leaf - He Is Running 285-75-16, (33x11.5), B.F.G. AT's, E Rated - The Installation Came Out Beautiful - Looks Factory! Only Better! - And No Electric Fans! - Yerington Nevada
Did you add any support back were you removed those two vertical supports?
@RicosGarage3 жыл бұрын
Yes. I forgot to mention that. What I did was lay down some 2" wide 1/8" flat bar where the supports were and stich welded in place. Thanks for the question that skipped my mind totally
@corylawrence1933 жыл бұрын
@@RicosGarage thank you for the great information. I’m in the process of building the same truck!!👍
@RicosGarage3 жыл бұрын
Thanks for the kind words. And most of all thanks for watching!
@JohnMontero-Nevaden3 жыл бұрын
@@RicosGarage I Put In 1"x2" .120 Wall Rectangular Tubing Vertically & Horizontally Across Bottom For Core Support For Frame Mounts & Also Used It For Bottom Radiator Mounts I Used All Origination Rubber Mounts For Radiator & Inter-Cooler
@jaredclark72712 жыл бұрын
In your video you mention using 14” fans. In your Amazon link I only see 12&16 inch. Are you sure they were 14” Maybe they are just sold out of 14”
@RicosGarage2 жыл бұрын
Probably sold out like everything else. You could probably get enough airflow with the 12s if you had to. The 16s physically won't fit as there is no room to spare with the 14
@davisrussell43873 жыл бұрын
What size lift kit are u running in this truck have same build and mines stock height but motor just about touches the front axle
@RicosGarage3 жыл бұрын
Running a 4" Rough Country lift.
@davisrussell43873 жыл бұрын
Ok cool and did u add leafs or anything for the extra weight?
@RicosGarage3 жыл бұрын
Nope ordered their 4" kit for a big block one ton and it holds up just fine
@thatcoolguy27633 жыл бұрын
Where do you get the rubber bushings?
@RicosGarage3 жыл бұрын
They are the factory 2nd gen Dodge intercooler mounts
@thatcoolguy27633 жыл бұрын
@@RicosGarage i know but I can’t find them anywhere
@RicosGarage3 жыл бұрын
I see. Mine came from my donor truck. I've never tried to source them from the aftermarket or dealership. Sorry
@thatcoolguy27633 жыл бұрын
@@RicosGarage yeah I ended up going to Home Depot and finding some rubber grommets 👍🏻