3'' ACCU LOCK VEVOR MACHINE VICE & HOW TO USE IT ON A SMALL BENCH DRILL

Рет қаралды 6,257

Жыл бұрын

See this excellent quality 3'' Vevor Accu-Lock Machine Vice and how to use it on a small bench drill. In this video I do a short review of the vice, how I have modified it slightly and the upgrades I have done to my bench drill to support and use it. It is great for setting up to do batch work on machine drilling and tapping operations. If you watch the video to the end you will see how you can operate the vice very quickly without using its handle. SEE THE ACCU-SEE ALL OF THE ACCU-LOCK MACHINE VICE LINKS BELOW;-
USE THIS LINK FOR THE USA SITE:- [US 🔗: s.vevor.com/bfQntQ].
USE THIS LINK FOR THE UK SITE:- [UK 🔗: s.vevor.com/bfQmwO].
US:
3 Inch Bench Vice: s.vevor.com/bfQntQ
4 Inch Bench Vice: s.vevor.com/bfQny5
5 Inch Bench Vice: s.vevor.com/bfQnze
6 Inch Bench Vice: s.vevor.com/bfQnzk
UK:
3 Inch Bench Vice: s.vevor.com/bfQnyd
4 Inch Bench Vice: s.vevor.com/bfQnyr
5 Inch Bench Vice: s.vevor.com/bfQnyx
6 Inch Bench Vice: s.vevor.com/bfQnyK

Пікірлер: 32

@SteveJordan Жыл бұрын

SEE THE LINKS FOR A RANGE OF THE ACCU-LOCK MACHINE VICES IN THE VIDEO DESCRIPTION ABOVE.

@gregh6794 Ай бұрын

Awesome idea for the handle grub screw

@MalJ-eb7nv Жыл бұрын

Thanks Steve, I purchased one and it arrived yesterday. I will mount mine on the drill press using your idea. Thankyou. (I have used a few of your ideas over the years from your videos)

@steph2211 Жыл бұрын

Nice looking vice Steve 👍👍

@MattysWorkshop Жыл бұрын

Gday Steve, they look like a good vice, I’ve seen a few other reviews on the Vevor vices and they have all been happy with it, thanks for sharing mate, cheers

@65cj55 Жыл бұрын

I have the 5'' one, no issues.

@buckinthetree1233 Жыл бұрын

That scissor jack under the drill press table looks terrible, but it's a genius idea. I have a very small tabletop drill press in my garage that I use for woodworking and a scissor jack that's going under the table next time I use it. I admire your keen idea.

@SteveJordan Жыл бұрын

Thanks. I have seen other people use the scissor jacks as well. I forgot to mention that if using them, to make sure one uses a spirit level on the table when adjusting it. I have been using it for many years, and it works great. Regards Steve

@MalJ-eb7nv Жыл бұрын

Useful set-up. Thankyou

@malcolmtill Жыл бұрын

Excellent, Very high quality video

@SteveJordan Жыл бұрын

Thanks for watching and for your encouraging comments. Regards Steve

@nobbysworkshop Жыл бұрын

These are great vices Steve. I got my one from Vevor two years ago. I use it on my Mini Mill, but without the rotating base to give me extra height. I can always add the base if I need to set an angle. I copied some of your bench drill mods, which I have shown in an earlier video. Cheers Nobby

@SteveJordan Жыл бұрын

Hi Nobby, Yes, they are excellent vices. What is your Mini Mill like? Did it need any modifications from new?

@nobbysworkshop Жыл бұрын

@@SteveJordan Hi Steve, I bought it used in 2016. Have done some mods to it. Replaced the torsion bar with a gas strut, and made a homemade power feed for the X travel. My first and third KZfaq videos show them. Most recently I added a DRO. Have a few videos on this also. Although it's only a lightweight mill, I've done a huge amount of work on it. All the best Steve. Cheers Nobby

@bobuk5722 Жыл бұрын

Hi Steve. Everything labelled. Great idea, not least for our Executors! I really like the scissor jack arrangement, you're very inventive. Not much chance of a workpiece escaping from that vice and of course a great safety feature to protect our hands. Thanks for showing.

@SteveJordan Жыл бұрын

Hi, Thanks. The safety feature was one of the reasons I got this one. A couple of years ago, I was drilling through an old V block, but stupidly holding it by hand. It snatched when the drill went through and caused some nasty injuries. It could have been a lot worse, though, but I learned never to hold anything by hand again!

@goldprogoldpro7809 Жыл бұрын

Thanks for another interesting video Steve. Is there an engraved line on the vise portion to work with the swivel degrees? I couldn't quite see anything in the video or at the website.

@SteveJordan Жыл бұрын

Hi, There is a ground flat where one should be, but mine doesn't have a line, so I shall just put one on. It looks like there should have been one as the flat is unpainted. It is easy to do, though. Regards Steve

@Dzon_Jacek Жыл бұрын

👍

@johnb2044 Жыл бұрын

Hi Steve quick noob question why have i seen on some vlogs that some folks use a round rod when clamping in the vice ???? almost like a spacer to stop the work piece walking in the jaws while being clamped.?

@SteveJordan Жыл бұрын

Hi John, I really don't know. I've never seen or come across it.

@65cj55 Жыл бұрын

Sometimes clamping with 3 points of contact is better.

@wilkbilt Жыл бұрын

Did Vevor furnish this vice to you, free of charge ?

@samrodian919 Жыл бұрын

@@SteveJordanyou didn't answer the question Steve

@SteveJordan Жыл бұрын

Hi, Sorry for the late reply. No, it costs me a lot of time and effort and money. I spent the best part of a day filming the video, then doing all the editing as well. People have got the wrong idea when they think things are free. Regards Steve

@adhawk5632 Жыл бұрын

So it was free? I've got one too, there good little vices. $80 is a bargain